Aigerim Sovet
Research Subjects
Aigerim Sovet has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Karakat Bolatzhan
Laboratory of SHS–New Materials, Institute of Combustion Problems, Bogenbay Batyr Street 172, Almaty 050012, Kazakhstan
2 shared publications - Nursultan Rakhym
Institute of Combustion Problems, Bogenbay Batyr St. 172, Almaty 050012, Kazakhstan
2 shared publications - Sanat Tolendiuly
Institute of Combustion Problems, Bogenbay Batyr St. 172, Almaty 050012, Kazakhstan
2 shared publications - Sergey M. Fomenko
Institute of Combustion Problems
2 shared publications - Sharafkhan Assylkhan
Institute of Combustion Problems, Bogenbay Batyr St. 172, Almaty 050012, Kazakhstan
2 shared publications - Abu Bakar Putra Ilhamsyah
Department of Applied Physics, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor, Malaysia
1 shared publication
Latest Publications
- Open Access
Effect of Co3O4 Concentration on the Phase Composition, Microstructure, and Superconducting Transition of Nonstoichiometric YBa2Cu3O7−δ Ceramics
The effect of Co3O4 concentration on the phase composition, surface morphology, geometric density, estimated porosity, compressive strength, and resistive superconducting transition of YBa2Cu3O7−δ ceramics was comparatively investigated. Undoped YBa2Cu3O7−δ and Co3O4-modified YBa2Cu3O7−δ ceramics containing 0.1, 0.5, 1.0, and 1.5 wt.% Co3O4 were prepared from the same nonstoichiometric Y–Ba–Cu–O precursor mixture by a solid-state reaction route followed by oxygen annealing. Phase composition was evaluated by X ray diffraction, surface morphology by scanning electron microscopy, geometric density from specimen mass and dimensions, compressive strength by uniaxial compression, and superconducting transition parameters by four probe electrical resistance measurements. The YBa2Cu3O7−δ phase remained the dominant crystalline phase in all specimens. The sample containing 0.1 wt.% Co3O4 exhibited the highest YBa2Cu3O7−δ content among the modified specimens, 65.2 wt.%, the highest measured compressive strength of 1.95 MPa, and the highest onset transition temperature of 95 K. The highest geometric density of 5.36 g/cm−3 and the lowest estimated porosity of 15.3% were obtained at 0.5 wt.% Co3O4. The specimens containing 1.0 and 1.5 wt.% Co3O4 showed lower YBa2Cu3O7−δ phase fractions and lower geometric density, and did not reach the zero-resistance state within the available measurement range. Although the 0.1 wt.% specimen exhibited a higher onset temperature than undoped YBa2Cu3O7−δ, its lower zero-resistance temperature and broader transition indicate that Co3O4 did not improve all superconducting parameters simultaneously. Since only one specimen was tested for each composition, the density and compressive strength trends should be regarded as preliminary.
Open AccessEffect of Co3O4 Concentration on the Phase Composition, Microstructure, and Superconducting Transition of Nonstoichiometric YBa2Cu3O7−δ Ceramics
The effect of Co3O4 concentration on the phase composition, surface morphology, geometric density, estimated porosity, compressive strength, and resistive superconducting transition of YBa2Cu3O7−δ ceramics was comparatively investigated. Undoped YBa2Cu3O7−δ and Co3O4-modified YBa2Cu3O7−δ ceramics containing 0.1, 0.5, 1.0, and 1.5 wt.% Co3O4 were prepared from the same nonstoichiometric Y–Ba–Cu–O precursor mixture by a solid-state reaction route followed by oxygen annealing. Phase composition was evaluated by X ray diffraction, surface morphology by scanning electron microscopy, geometric density from specimen mass and dimensions, compressive strength by uniaxial compression, and superconducting transition parameters by four probe electrical resistance measurements. The YBa2Cu3O7−δ phase remained the dominant crystalline phase in all specimens. The sample containing 0.1 wt.% Co3O4 exhibited the highest YBa2Cu3O7−δ content among the modified specimens, 65.2 wt.%, the highest measured compressive strength of 1.95 MPa, and the highest onset transition temperature of 95 K. The highest geometric density of 5.36 g/cm−3 and the lowest estimated porosity of 15.3% were obtained at 0.5 wt.% Co3O4. The specimens containing 1.0 and 1.5 wt.% Co3O4 showed lower YBa2Cu3O7−δ phase fractions and lower geometric density, and did not reach the zero-resistance state within the available measurement range. Although the 0.1 wt.% specimen exhibited a higher onset temperature than undoped YBa2Cu3O7−δ, its lower zero-resistance temperature and broader transition indicate that Co3O4 did not improve all superconducting parameters simultaneously. Since only one specimen was tested for each composition, the density and compressive strength trends should be regarded as preliminary.
- Open Access
Radiation-Induced Defect Engineering in REBCO High-Temperature Superconductors: Defect Morphology, Vortex Pinning, and Technological Reliability
Radiation-induced defect engineering is an effective approach for modifying the vortex-pinning landscape in high-temperature superconductors, particularly REBCO-coated conductors and Bi-based cuprates. This review critically summarizes the relationship between irradiation parameters, defect morphology, and superconducting performance. The discussion covers point defects, defect clusters, columnar tracks, planar defects, and displacement cascades generated by electrons, gamma rays, light ions, heavy ions, and neutrons. Special attention is given to the dual role of irradiation: moderate defect concentrations can enhance the critical current density by introducing artificial pinning centers, whereas excessive disorder suppresses the superconducting transition temperature and degrades current transport. The review also discusses the relevance of irradiation effects for fusion magnets, space technologies, accelerator systems, and high-field applications. Finally, the review identifies key challenges for future HTS radiation engineering, including cryogenic in situ irradiation, coupled radiation–strain–field experiments, damage metrics beyond dpa, and multi-scale models capable of linking atomic defect production, oxygen disorder, vortex pinning, and macroscopic Jc/Tc degradation.
Open AccessRadiation-Induced Defect Engineering in REBCO High-Temperature Superconductors: Defect Morphology, Vortex Pinning, and Technological Reliability
Radiation-induced defect engineering is an effective approach for modifying the vortex-pinning landscape in high-temperature superconductors, particularly REBCO-coated conductors and Bi-based cuprates. This review critically summarizes the relationship between irradiation parameters, defect morphology, and superconducting performance. The discussion covers point defects, defect clusters, columnar tracks, planar defects, and displacement cascades generated by electrons, gamma rays, light ions, heavy ions, and neutrons. Special attention is given to the dual role of irradiation: moderate defect concentrations can enhance the critical current density by introducing artificial pinning centers, whereas excessive disorder suppresses the superconducting transition temperature and degrades current transport. The review also discusses the relevance of irradiation effects for fusion magnets, space technologies, accelerator systems, and high-field applications. Finally, the review identifies key challenges for future HTS radiation engineering, including cryogenic in situ irradiation, coupled radiation–strain–field experiments, damage metrics beyond dpa, and multi-scale models capable of linking atomic defect production, oxygen disorder, vortex pinning, and macroscopic Jc/Tc degradation.