Shunji Hiwatashi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Shunji Hiwatashi has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Kotaro Ueno
Interdisciplinary Graduate School of Engineering Sciences, Kyushu University
1 shared publication - Koutarou Hayashi
Research and Development Bureau, Nippon Steel Corporation
1 shared publication - Manabu Takahashi
Faculty of Engineering Sciences, Kyushu University
1 shared publication - Masatoshi Mitsuhara
Faculty of Engineering Sciences, Kyushu University
1 shared publication - Rina Fujimura
Faculty of Engineering Sciences, Kyushu University
1 shared publication
Latest Publications
- Open Access
- 15 February 2025
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 65 (2) , 274-283
Effects of Manganese on Microstructure and Work-hardening Behavior of Low-carbon Lath Martensitic Steel
Microstructures of lath martensite have been studied intensively to understand their effect on the mechanical properties of steels. It is, however, said that the relation between microstructural factors and mechanical properties has not been clarified yet. The plastic deformation behavior of fully lath martensitic steels has become important because they are applied to automobile body structures such as bumper reinforcement. It is, therefore, important to understand the microstructural factors that control the work-hardening behavior of fully martensitic steels. Although we could not clarify differences in microstructural factors when manganese (Mn) concentrations of steels are altered, the work-hardening of 8 mass%Mn martensitic steel is much higher than that of 5 mass%Mn martensitic steel. It was found using the digital image correlation (DIC) method, that the strain concentration due to the in-lath-plane slip deformation is more developed in 5 mass%Mn martensitic steel than 8 mass%Mn martensitic steel. Transmission electron microscope (TEM) observations revealed the existence of two types of fine twins inside laths. Long twins that are parallel to the longitude of the lath are observed both in 5 mass%Mn and 8 mass%Mn martensitic steels. Short twins that partially cross the laths, on the other hand, can only be found in 8 mass%Mn martensitic steel. Since twin boundaries are high angle boundaries, the short twins are supposed to prevent the development of in-lath-plane slip deformation. This seems to be the mechanism of higher work-hardening behavior observed in 8 mass%Mn martensitic steel.
- 15 February 2025
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 65 (2) , 274-283
Open AccessEffects of Manganese on Microstructure and Work-hardening Behavior of Low-carbon Lath Martensitic Steel
Microstructures of lath martensite have been studied intensively to understand their effect on the mechanical properties of steels. It is, however, said that the relation between microstructural factors and mechanical properties has not been clarified yet. The plastic deformation behavior of fully lath martensitic steels has become important because they are applied to automobile body structures such as bumper reinforcement. It is, therefore, important to understand the microstructural factors that control the work-hardening behavior of fully martensitic steels. Although we could not clarify differences in microstructural factors when manganese (Mn) concentrations of steels are altered, the work-hardening of 8 mass%Mn martensitic steel is much higher than that of 5 mass%Mn martensitic steel. It was found using the digital image correlation (DIC) method, that the strain concentration due to the in-lath-plane slip deformation is more developed in 5 mass%Mn martensitic steel than 8 mass%Mn martensitic steel. Transmission electron microscope (TEM) observations revealed the existence of two types of fine twins inside laths. Long twins that are parallel to the longitude of the lath are observed both in 5 mass%Mn and 8 mass%Mn martensitic steels. Short twins that partially cross the laths, on the other hand, can only be found in 8 mass%Mn martensitic steel. Since twin boundaries are high angle boundaries, the short twins are supposed to prevent the development of in-lath-plane slip deformation. This seems to be the mechanism of higher work-hardening behavior observed in 8 mass%Mn martensitic steel.