DADiğdem Atabek

Diğdem Atabek

*This is an algorithmically generated author record based on publicly available information.

Diğdem Atabek has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Direnç Nokta Kaynağı ile Birleştirilmiş AlSi Kaplamalı SABC1470 Çeliklerinde Patchwork Uygulamasının Mikroyapısal ve Mekanik Olarak İncelenmesi

    by Yusuf Taşkiran, Ümran Kiskiç, Yiğit Gönülalan, Diğdem Atabek

    Bu çalışma, AlSi kaplamalı SABC1470 çeliği kullanılarak direnç nokta kaynağı ile yapılan patchwork üretim yönteminin, sıcak şekillendirme prosesi öncesi ve sonrasında mikroyapısal ve mekanik davranışlarının, kaynaklanabilirlik fizibilitesi üzerindeki etkilerini analiz etmeyi amaçlamaktadır. Deneysel çalışmalar kapsamında, aynı kalınlığa ve malzeme özelliğine sahip iki sac plaka, direnç nokta kaynak yöntemi ile birleştirilmiş ve farklı kaynak parametrelerinin kaynak çekirdek çapına ve mikroyapıya etkisi detaylı olarak incelenmiştir. Spot kaynağı sonrası uygulanan presle bükme işlemi ile radius bölgelerinde meydana gelen yapısal değişimler taramalı elektron mikroskobu (SEM) yardımıyla analiz edilmiştir. Özellikle çekirdek çapının standartlara uygunluğu değerlendirilmiş; sıcak şekillendirme prosesi sonrasında spot çekirdeğinde meydana gelen kayma ve çatlak oluşumları ile ilişkisi ortaya konmuştur. Bu bulgular, direnç nokta kaynağı ile yapılan patchwork uygulamalarında kaynak kalitesinin ve mikroyapısal bütünlüğün üretim sonrası şekillendirme davranışı üzerindeki belirleyici etkisini göstermektedir.

  • Open Access

    Influence of Pulse Number on Nugget Formation and Joint Performance in Resistance Spot-Welded 2 GPa Press-Hardened Steel

    by Ümran Kıskıc, Onur Muratal, Samet Demir, Digdem Atabek, Orcun Yöntem, Ridvan Yamanoglu

    The resistance spot welding (RSW) of 2 GPa press-hardened steels, which have been widely used in industrial applications in recent years, poses significant challenges due to brittleness caused by the fully martensitic microstructure, subcritical heat-affected zone softening, and interfacial cracking influenced by the coating. The effect of the number of pulses during welding on nugget formation and fracture behavior remains a critical issue. In this study, microstructural characterizations using optical microscopy and SEM, microhardness testing, tensile-shear tests, and fractography analyses were conducted across different pulse conditions (insufficient, moderate, optimal, and excessive heat input). The obtained results demonstrate that the pulse number is a decisive parameter in nugget formation and joint behavior due to its governing effect on heat input and thermal history. While increasing heat input promotes nugget development, excessive pulsing induces localized degradation, severe indentation, and centerline flaws. Under optimal pulsing conditions (Pulse 7), uniform fusion, refined martensitic transformation, an FZ hardness of approximately 580–600 HV, and a maximum shear strength of approximately 790 MPa were achieved with complete button pull-out failure. In contrast, under low pulse conditions, the narrow fusion zone resulted in hardness approaching 700 HV and brittle interfacial fracture along the faying interface driven by the fully hardened martensitic matrix and micro-shrinkage voids. These findings establish clear processing guidelines for pulse modulation to enhance weld integrity and joint reliability in 2 GPa press-hardened steels.

  • Robotik Ark Kaynağında CuCr1Zr ve W-Cu Alaşımlı Kontak Tiplerin Aşınma Direncinin ve Kaynak Dikişi Üzerindeki Etkilerinin Karşılaştırılması

    by Mehmet Has, Diğdem Atabek, Onur Muratal

    Robotik gazaltı ark kaynaklarında kullanılan bakır alaşımlı kontak tiplerin uçları (kontak meme), kayar temas ve termomekanik yüklere maruz kalmasından dolayı aşınarak çapları genişlemektedir. Genişleyen çaplar kullanılan kaynak telinin konumlandırmasını güçleştirdiğinden, kaynak hassasiyetini etkilemektedir. Bundan dolayı farklı alaşımlardan üretilen kontak tip kullanımı arayışı doğmaktadır. Bu çalışmada, bakır alaşımlı (CuCr1Zr) kontak tiplerin kullanımına alternatif olarak tungsten alaşımlı (W80-Cu20) kontak tip geliştirilerek robotik ark kaynağı uygulamasında test edilmiştir. Geliştirilen kontak tipte, bakırın (Cu) elektriksel iletkenliğinden faydalanılırken, tungstenin (W) mekanik aşınma direncinden faydalanılması amaçlanmıştır. Referans parça olarak 600 MPa dayanımlı düşük karbonlu çelik seçilmiştir. Yapılan uygulamalarda, her iki alaşımlı kontak tip bu referans parça üzerinde denenmiştir. Denemede 25’er adet parça üretilmiştir. Her iki kontak tip denemelerinde de aynı kaynak parametreleri kullanılmıştır. Ark kaynak işlemi öncesi ve sonrası her iki kontak tipin uç çapları ölçülerek aşınma dayanım performansları incelenmiştir. CuCr1Zr alaşımlı kontak tip ucunda, yapılan ölçümler sonucunda yaklaşık 12.86% oranında bir çap aşınması tespit edilmiştir. Tungsten alaşımlı kontak ucunda ise çap aşınma oranı oldukça düşük seviyede, yaklaşık 1.43% olarak belirlenmiştir. Bu hesaplamalara göre, W80-Cu20 alaşımlı kontak tip tasarımının CuCr1Zr alaşımlı kontak tipten aşınma dayanımı olarak daha üstün olduğu görülmüştür. Kaynak işlemiyle birleştirilen parçalara kesme testi ve mikroyapı analizi yapılmıştır. Analiz sonucunda, yeni geliştirilen W80-Cu20 alaşımlı kontak tipin üzerinden geçen elektriği daha az ilettiği, buna bağlı olarak akımın da doğru orantıda azalarak daha güçsüz ark oluşturduğu ve CuCr1Zr alaşımlı kontak tipe göre daha az kaynak nüfuziyeti sağladığı görülmüştür. CuCr1Zr kontak tip kullanılarak yapılan kaynak işlemlerinde, W80-Cu20 ile üretilen parçalara kıyasla ısıdan etkilenen bölgelerin daha geniş ancak mikroyapı açısından daha düzenli olduğu, ayrıca tane büyümesinin daha sınırlı gerçekleştiği gözlemlenmiştir.

  • Effect of Thickness Reduction in BIW Weight Reduction: Transition from 600DU to 800DU on Splitting Behavior

    by Teoman Tilki, Yiğit Gönülalan, Onur Muratal, Diğdem Atabek

    Material selection for creating a rigid and high-energy absorption lightweight BIW is critical in terms of fuel economy and emissions. In this context, material forming limits and mechanical behavior during stamping processes are the most important factors in the creation of lightweight BIW’s. Therefore, enhancing strength and reducing material thickness stand out as the primary ways to comply with industry standards and reduce the body weight. In weight reduction efforts with dual-phase steels, thinning may lead to splitting due to the increased martensitic island structure in regions with the highest Mn and C content in dual-phase materials. In hot- and cold-rolled dual-phase 800DU material with a thickness of 1mm, splitting may occur during forming simulation due to the martensitic structure to distribute inhomogeneously, surpassing the critical threshold of the forming simulation curve when compared to cold-rolled 600DU material with a thickness of 1.2mm. This study addresses the thinning-induced splitting issue encountered in weight reduction applications, determining the optimal choice between different rolling types under a die produced for 600DU material with a thickness of 1.2mm, using both hot and cold-rolled materials. In line with the purpose of the study, trials were conducted with two different 800DU materials under forming dies. Formability simulations and mechanical tests were performed, and analyses were carried out in terms of microstructure, thinning, and edge cracking performance. The characterization of the materials was conducted using a scanning electron microscope (SEM) equipped with an EDX apparatus. Following the characterization, tensile tests were performed in three different rolling directions to determine the mechanical properties of the materials. To evaluate the resistance of the materials to edge cracking, Hole Expansion (HE) tests were conducted. As a result of the improvements and analyses made by replacing the 600DU material with a thickness of 1.2mm with cold-rolled 800DU material with a thickness of 1.0mm, the proposed application appears feasible for the part geometry under consideration.

  • Comparative Investigation of Edge Cracking Behavior in 600 MPa Dual Phase (DU) Steel Sheets from Different Manufacturers

    by Zeki Ahmet Ekmen, Yiğit Gönülalan, Onur Muratal, Diğdem Atabek

    Recent advancements in the automotive industry have emphasized the importance of fuel efficiency, weight reduction, and durability. In response, AHSS materials have become widely used, particularly in cold forming. However, their high strength reduces formability, leading to challenges such as edge cracking. In this study, 600DU steel from two different mills was tested. Tensile tests were conducted on EU1 and EU2 at 0°, 45°, and 90° to the rolling direction per JIS Z 2241 No. 5. The tensile strength values were similar, but EU2 showed higher elongation. A hole expansion test revealed an average expansion of ~27% for EU1 and ~60% for EU2. Vickers hardness was measured under an HV 10 load. Metallographic preparation was followed by microstructural analysis using optical and SEM microscopy. In the AutoForm simulation analysis, the average thickness reduction of the EU1 steel was determined to be 19%, while that of the EU2 steel was measured at 11%. These results indicate that the EU1 steel exhibits 8% greater thinning compared to the EU2 steel. This study examines the formability of 600DU (dual-phase) AHSS steel from different manufacturers using numerical and experimental methods. The findings provide key insights into AHSS forming performance and help address potential issues. Numerical and experimental data modeling will contribute to optimizing manufacturing processes.