Yerlan Kushekov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yerlan Kushekov has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Bakhadyr Kopzhassarov
South Kazakhstan University named after M. Auezov, 160012, 5 Tauke Khana, Shymkent
1 shared publication Georgiy Tokmadzheshvili
Kazakh Academy of Architecture and Construction Sciences, 050000, 21 Solodovnikova, Almaty
1 shared publication- Gulnaz Ibraimbayeva
International Educational Corporation, Kazakh Leading Academy of Architecture and Civil Engineering
1 shared publication - Maratbek Zhuginissov
“Technopark Stroytech” Scientific Research Laboratory of Construction and Building Materials, Satbayev University, Satpayev Street 22, Almaty 050013, Kazakhstan
1 shared publication - Mederbay Saduakassov
Kazakh Academy of Architecture and Construction Sciences, 050000, 21 Solodovnikova, Almaty
1 shared publication - Ruslan E. Nurlybayev
Institute of Architecture and Civil Engineering, Satbayev University, 22a Satpaev St., Almaty A03A2C6, Kazakhstan
1 shared publication
Latest Publications
- Open Access
- 29 September 2026
- Published by Technobius in Technobius
- Vol. 6 (3) , 0109
Hyper-pressing technologies and properties of construction products: a review
High-pressure forming is increasingly recognized as a promising method for producing low-energy masonry units from natural minerals and secondary raw materials. This review consolidates current knowledge on compressed earth blocks, cementitious high-pressure bricks, alkali-activated products, and ultra-high-pressure waste-derived bricks. Emphasis is placed on raw material selection, mixture preparation, forming moisture, compaction pressure, curing conditions, structure formation mechanisms, and resulting engineering properties. The literature indicates that pressure-induced particle rearrangement and pore reduction must be integrated with hydration, pozzolanic reactions, alkali activation, or carbonation to achieve stable long-term performance. Increasing pressure typically enhances density, strength, and water resistance up to an effective densification threshold, beyond which further pressure may yield limited benefits or induce microcracking and elastic recovery. Industrial, mining, construction, and agricultural wastes can substitute for significant proportions of natural raw materials; however, their use necessitates careful control of particle grading, chemical variability, soluble salts, and potentially hazardous components. The environmental advantages of avoiding firing may be offset by high Portland cement content, extended transport distances, and energy-intensive waste pretreatment. This review highlights insufficient standardization of terminology, specimen geometry, compaction procedures, curing regimes, and durability assessment as major obstacles to comparison. Future research should focus on long-term exposure testing, full-scale production, environmental safety, life-cycle assessment, and the development of low-carbon binder systems.
- 29 September 2026
- Published by Technobius in Technobius
- Vol. 6 (3) , 0109
Open AccessHyper-pressing technologies and properties of construction products: a review
High-pressure forming is increasingly recognized as a promising method for producing low-energy masonry units from natural minerals and secondary raw materials. This review consolidates current knowledge on compressed earth blocks, cementitious high-pressure bricks, alkali-activated products, and ultra-high-pressure waste-derived bricks. Emphasis is placed on raw material selection, mixture preparation, forming moisture, compaction pressure, curing conditions, structure formation mechanisms, and resulting engineering properties. The literature indicates that pressure-induced particle rearrangement and pore reduction must be integrated with hydration, pozzolanic reactions, alkali activation, or carbonation to achieve stable long-term performance. Increasing pressure typically enhances density, strength, and water resistance up to an effective densification threshold, beyond which further pressure may yield limited benefits or induce microcracking and elastic recovery. Industrial, mining, construction, and agricultural wastes can substitute for significant proportions of natural raw materials; however, their use necessitates careful control of particle grading, chemical variability, soluble salts, and potentially hazardous components. The environmental advantages of avoiding firing may be offset by high Portland cement content, extended transport distances, and energy-intensive waste pretreatment. This review highlights insufficient standardization of terminology, specimen geometry, compaction procedures, curing regimes, and durability assessment as major obstacles to comparison. Future research should focus on long-term exposure testing, full-scale production, environmental safety, life-cycle assessment, and the development of low-carbon binder systems.
- Open Access
- 1 September 2025
- Published by Ital Publication in Civil Engineering Journal
- Vol. 11 (9) , 3901-3915
Application of Feldspar Sand in Non-Autoclaved Foam Concrete Technology
The aim of this study is to determine the possibility of producing non-autoclaved foam concrete of grade M35 with a density of 900 kg/m³. A distinctive feature of this development is the testing of twin samples from the same batch: some were steamed in a chamber at 90 °C under normal atmospheric pressure, while others were autoclaved at a pressure of 8 bar and a temperature of 170 °C. It was established that ordinary natural feldspar sands with a fineness modulus ranging from 1.43 to 2.45, containing quartz below the standard-regulated levels, can be used in the production of non-autoclaved foam concrete. It is not possible to obtain non-autoclaved D900 foam concrete of grade M35 strength using only cement, sand, and foaming agent. To achieve the specified strength, it is necessary to use coarse sand with a fineness modulus (FM) greater than 3, subjected to short-term grinding to reduce the FM to recommended values, and to additionally introduce sol-gel liquid glass. The novelty lies in the experimental confirmation of the features of strength formation in cellular concrete under both non-autoclaved and autoclaved curing conditions. Comparative tests showed that high strength in cellular concrete is achieved only when a chemical bond forms between the products of cement hydrolysis and hydration with quartz sand grains—conditions made possible through autoclaving.
- 1 September 2025
- Published by Ital Publication in Civil Engineering Journal
- Vol. 11 (9) , 3901-3915
Open AccessApplication of Feldspar Sand in Non-Autoclaved Foam Concrete Technology
The aim of this study is to determine the possibility of producing non-autoclaved foam concrete of grade M35 with a density of 900 kg/m³. A distinctive feature of this development is the testing of twin samples from the same batch: some were steamed in a chamber at 90 °C under normal atmospheric pressure, while others were autoclaved at a pressure of 8 bar and a temperature of 170 °C. It was established that ordinary natural feldspar sands with a fineness modulus ranging from 1.43 to 2.45, containing quartz below the standard-regulated levels, can be used in the production of non-autoclaved foam concrete. It is not possible to obtain non-autoclaved D900 foam concrete of grade M35 strength using only cement, sand, and foaming agent. To achieve the specified strength, it is necessary to use coarse sand with a fineness modulus (FM) greater than 3, subjected to short-term grinding to reduce the FM to recommended values, and to additionally introduce sol-gel liquid glass. The novelty lies in the experimental confirmation of the features of strength formation in cellular concrete under both non-autoclaved and autoclaved curing conditions. Comparative tests showed that high strength in cellular concrete is achieved only when a chemical bond forms between the products of cement hydrolysis and hydration with quartz sand grains—conditions made possible through autoclaving.