Riccardo Moleri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Riccardo Moleri has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Andrea Leonardo Lacaita
Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milan, Italy
4 shared publications - Michele Rossoni
Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milan, Italy
4 shared publications - Salvatore Levantino
Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milan, Italy
4 shared publications - Simone Mattia Dartizio
Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milan, Italy
4 shared publications - Daniele Lodi Rizzini
Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milan, Italy
3 shared publications - Francesco Tesolin
Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milan, Italy
3 shared publications
Latest Publications
- Open Access
- 13 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 1844-1859
A Wideband Digitally Assisted Frequency Tripler With Adaptively Optimized Output Power in 55-nm SiGe BiCMOS
This article presents a 28–38-GHz frequency tripler implemented in 55-nm SiGe BiCMOS technology with a novel on-chip background calibration technique. This technique continuously optimizes the circuit performance by maximizing output power and improving fundamental harmonic rejection. The proposed tripler achieves wideband operation and robust performance across varying operating conditions and input-power levels. The calibrated tripler demonstrates more than 40 dB of fundamental harmonic rejection and a 10.2-GHz (30.3%) 3-dB bandwidth. It occupies an area of 0.16 mm2 and consumes 54 mW of power. The results show the tripler maintains its performance over a 13-dB input-power variation, confirming the effectiveness of the proposed calibration method.
- 13 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 1844-1859
Open AccessA Wideband Digitally Assisted Frequency Tripler With Adaptively Optimized Output Power in 55-nm SiGe BiCMOS
This article presents a 28–38-GHz frequency tripler implemented in 55-nm SiGe BiCMOS technology with a novel on-chip background calibration technique. This technique continuously optimizes the circuit performance by maximizing output power and improving fundamental harmonic rejection. The proposed tripler achieves wideband operation and robust performance across varying operating conditions and input-power levels. The calibrated tripler demonstrates more than 40 dB of fundamental harmonic rejection and a 10.2-GHz (30.3%) 3-dB bandwidth. It occupies an area of 0.16 mm2 and consumes 54 mW of power. The results show the tripler maintains its performance over a 13-dB input-power variation, confirming the effectiveness of the proposed calibration method.
- Open Access
- 4 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-17
A Low Jitter and Low Spur Fractional-N Digital PLL Based on a DTC Chopping Technique
This work presents a digital-to-time converter (DTC)-based fractional-N digital phase-locked loop (PLL) designed to achieve simultaneously low jitter and low spurs. We introduce a novel DTC chopping technique that effectively mitigates fractional spurs, which we identify as predominantly arising from even-order nonlinearity invariable-slope (VS) DTCs. The proposed technique suppresses such spurs by randomly alternating the DTC position between the reference and divider signal paths. In addition, it proves effective in reducing the DTC flicker noise contribution. To ensure robust operation across process, voltage, and temperature (PVT) spreads, the design incorporates several background adaptive digital algorithms. Fabricated in a 28-nm CMOS process, the synthesizer occupies an active area of 0.22 mm2 and consumes 16.7 mW. At a 9.275-GHz near-integer channel, the measured worst case in-band fractional spur remains below −63 dBc, and the integrated rms jitter under 80 fs, yielding a jitter-power figure of merit (FoM) of −249.8 dB.
- 4 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-17
Open AccessA Low Jitter and Low Spur Fractional-N Digital PLL Based on a DTC Chopping Technique
This work presents a digital-to-time converter (DTC)-based fractional-N digital phase-locked loop (PLL) designed to achieve simultaneously low jitter and low spurs. We introduce a novel DTC chopping technique that effectively mitigates fractional spurs, which we identify as predominantly arising from even-order nonlinearity invariable-slope (VS) DTCs. The proposed technique suppresses such spurs by randomly alternating the DTC position between the reference and divider signal paths. In addition, it proves effective in reducing the DTC flicker noise contribution. To ensure robust operation across process, voltage, and temperature (PVT) spreads, the design incorporates several background adaptive digital algorithms. Fabricated in a 28-nm CMOS process, the synthesizer occupies an active area of 0.22 mm2 and consumes 16.7 mW. At a 9.275-GHz near-integer channel, the measured worst case in-band fractional spur remains below −63 dBc, and the integrated rms jitter under 80 fs, yielding a jitter-power figure of merit (FoM) of −249.8 dB.
- 30 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (12) , 4572-4586
A Low-Noise Digital PLL With an Adaptive Common-Mode Resonance Tuning Technique for Voltage-Biased Oscillators
This work presents a digital phase-locked loop (PLL) incorporating an adaptive common-mode (CM) resonance tuning technique applied to a voltage-biased digitally-controlled oscillator (DCO). The method leverages the principle that the sensitivity of the oscillator frequency to a dither signal injected into the gate voltage of the cross-coupled transistors diminishes to near zero when the CM resonance is optimally tuned for minimal phase noise (PN). By detecting and nullifying this sensitivity, the proposed technique automatically adjusts the CM resonance to its ideal value. This background operation is continuous across the entire tuning range. The concept was validated through a digital PLL prototype fabricated in a 28-nm CMOS process, which achieved a jitter of 45.9 fs, a power-versus-jitter figure-of-merit of −257 dB, and a PN of −146.6 dBc/Hz at 10-MHz offset from a 4.75-GHz carrier, all within an active area of 0.21 mm2 .
- 30 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (12) , 4572-4586
A Low-Noise Digital PLL With an Adaptive Common-Mode Resonance Tuning Technique for Voltage-Biased Oscillators
This work presents a digital phase-locked loop (PLL) incorporating an adaptive common-mode (CM) resonance tuning technique applied to a voltage-biased digitally-controlled oscillator (DCO). The method leverages the principle that the sensitivity of the oscillator frequency to a dither signal injected into the gate voltage of the cross-coupled transistors diminishes to near zero when the CM resonance is optimally tuned for minimal phase noise (PN). By detecting and nullifying this sensitivity, the proposed technique automatically adjusts the CM resonance to its ideal value. This background operation is continuous across the entire tuning range. The concept was validated through a digital PLL prototype fabricated in a 28-nm CMOS process, which achieved a jitter of 45.9 fs, a power-versus-jitter figure-of-merit of −257 dB, and a PN of −146.6 dBc/Hz at 10-MHz offset from a 4.75-GHz carrier, all within an active area of 0.21 mm2 .