E. V. Iasharova
E. V. Iasharova has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
A. A. Galkin Donetsk Institute of Physics and Technology
1 shared publicationA.N. Gangalo
1 shared publicationA.V. Garshev
1 shared publication- Albina M. Murashko
Department of Materials Science, Lomonosov Moscow State University, Building, 73, Leninskie Gory, 1, 119991 Moscow, Russia
1 shared publication - Alexander N. Gangalo
Donetsk Institute for Physics and Engineering named after A.A. Galkin; Institute of Physics of Mining Processes
1 shared publication D.S. Larionov
1 shared publication
Latest Publications
- 27 August 2026
- Published by Pleiades Publishing Ltd in Bulletin of the Russian Academy of Sciences: Physics
- Vol. 90 (8) , 1334-1339
Relaxation of the Strength Properties of Ultrafine-Grained Copper during Hydrostatic Extrusion
The influence of the deformation mode of hydrostatic extrusion on the strength properties of ultrafine-grained copper obtained by equal-channel angular pressing was investigated. It was shown that the strength increases monotonically with increasing strain up to e = 0.9. A further increase in strain causes relaxation decrease in strength due to deformation heating and to a decrease in dislocation density.
- 27 August 2026
- Published by Pleiades Publishing Ltd in Bulletin of the Russian Academy of Sciences: Physics
- Vol. 90 (8) , 1334-1339
Relaxation of the Strength Properties of Ultrafine-Grained Copper during Hydrostatic Extrusion
The influence of the deformation mode of hydrostatic extrusion on the strength properties of ultrafine-grained copper obtained by equal-channel angular pressing was investigated. It was shown that the strength increases monotonically with increasing strain up to e = 0.9. A further increase in strain causes relaxation decrease in strength due to deformation heating and to a decrease in dislocation density.
- 1 January 2025
- Published by Science & Technology in Deformation and Fracture of Materials
- No. 10
Study of mechanical properties of ceramic materials based on ca3(po4)2-ca2,5na(po4)2, obtained by 3d printing
The mechanical properties of ceramic materials based on high-temperature phases of tricalcium phosphate α-Ca3(PO4)2 and sodium rhenanite Ca2,5Na(PO4)2, as well as their composites in the 1:1 molar ratio, fabricated by the stereolithography method, have been studied. It is shown that the composite (biphase) ceramics produced by pressing followed by firing exhibit the highest density - 92% - and ultimate compression strength up to 120 MPa. For ceramic materials synthesized by 3D printing with a specified porosity of 70%, the influence of the pore space architecture on the mechanical properties under compression was determined. It is shown that ceramics with the Kelvin architecture exhibit greater strength than ceramics with the gyroid architecture. A temperature-time regime for heat treatment of the printed samples was developed to remove the polymer matrix, resulting in crack-free ceramics. It was found that the ultimate compressive strength of 3D ceramics based on α-Ca3(PO4)2 reached 2.5 MPa, which is acceptable for medical applications.
- 1 January 2025
- Published by Science & Technology in Deformation and Fracture of Materials
- No. 10
Study of mechanical properties of ceramic materials based on ca3(po4)2-ca2,5na(po4)2, obtained by 3d printing
The mechanical properties of ceramic materials based on high-temperature phases of tricalcium phosphate α-Ca3(PO4)2 and sodium rhenanite Ca2,5Na(PO4)2, as well as their composites in the 1:1 molar ratio, fabricated by the stereolithography method, have been studied. It is shown that the composite (biphase) ceramics produced by pressing followed by firing exhibit the highest density - 92% - and ultimate compression strength up to 120 MPa. For ceramic materials synthesized by 3D printing with a specified porosity of 70%, the influence of the pore space architecture on the mechanical properties under compression was determined. It is shown that ceramics with the Kelvin architecture exhibit greater strength than ceramics with the gyroid architecture. A temperature-time regime for heat treatment of the printed samples was developed to remove the polymer matrix, resulting in crack-free ceramics. It was found that the ultimate compressive strength of 3D ceramics based on α-Ca3(PO4)2 reached 2.5 MPa, which is acceptable for medical applications.
- 1 January 2025
- Published by Science & Technology in Deformation and Fracture of Materials
- No. 10
Effect of hydropressing on mechanical properties of ultrafine-grained copper
The effect of hydropressing with a true single strain of e = 0.3-1.2 on the tensile mechanical properties of copper with an ultrafine-grained structure formed by equal-channel angular pressing has been studied. It is shown that to obtain the best combination of mechanical properties of ultrafine-grained copper, hydropressing should be performed in a strain range of e = 0.6-0.9. Depending on the deformation magnitude, the ultimate strength of ultrafine-grained copper can be further increased by ~10%, and the shear stress at fracture by ~40%. Failure mechanisms were studied.
- 1 January 2025
- Published by Science & Technology in Deformation and Fracture of Materials
- No. 10
Effect of hydropressing on mechanical properties of ultrafine-grained copper
The effect of hydropressing with a true single strain of e = 0.3-1.2 on the tensile mechanical properties of copper with an ultrafine-grained structure formed by equal-channel angular pressing has been studied. It is shown that to obtain the best combination of mechanical properties of ultrafine-grained copper, hydropressing should be performed in a strain range of e = 0.6-0.9. Depending on the deformation magnitude, the ultimate strength of ultrafine-grained copper can be further increased by ~10%, and the shear stress at fracture by ~40%. Failure mechanisms were studied.