Xinqing Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xinqing Wang has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Jing Wang
College of Mechanical Engineering, Donghua University, Shanghai 201620, China
4 shared publications Kun Wang
2 shared publicationsYiming Han
2 shared publications- Bingli Lan
Zhongshan Hecheng Lubrication Materials Co., Ltd., Zhongshan 528403, China
1 shared publication - Chang Shu
College of Mechanical Engineering, Donghua University, Shanghai 201620, China
1 shared publication - Hengrui Du
College of Mechanical Engineering, Donghua University, Shanghai 201620, China
1 shared publication
Latest Publications
- Open Access
- 25 September 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (10) , 365
Effects of Nominal Duty Cycle and Delayed Energization on the Reciprocating Friction and Wear Performance of GCr15 Bearing Steel
Under intermittent source-side excitation, electric-drive systems can maintain mechanical operation, so nominal energization parameters do not directly represent the interfacial electrical state. GCr15 ball-on-disk tests compared dry and polyalphaolefin (PAO 40)-lubricated conditions at 6 N under 5 V, 1 Hz switching. Tests covered nominal duty cycles from D = 0 to 1.00, where D is the ratio of the voltage on-time to the voltage period. Equal-on-time friction tests compared periodic D = 0.50, on→off and off→on. Wear was compared among periodic D = 0.50, off→on, and continuous direct current (DC). Friction increased overall with D. Longer on-time prolonged concurrent microcontact Joule heating and mechanical friction. Dry-sliding wear volume varied non-monotonically, peaking at D = 0.50 with changes in surface-layer removal and O-containing debris retention. Under PAO 40 boundary/mixed lubrication, wear-track width and volume increased monotonically with electrical-heating-related changes in oil film support and separation, microcontact, plowing, and plastic deformation. Equal-on-time friction histories differed. Periodic D = 0.50 and off→on produced similar wear volumes but different morphologies. Dry off→on and continuous DC wear volumes were close. Wear depended on timing and interface state at energization. Interface evolution altered contact resistance and voltage division, feeding back on wear. These findings support energization-parameter and bearing wear risk assessment under intermittent source-side excitation.
- 25 September 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (10) , 365
Open AccessEffects of Nominal Duty Cycle and Delayed Energization on the Reciprocating Friction and Wear Performance of GCr15 Bearing Steel
Under intermittent source-side excitation, electric-drive systems can maintain mechanical operation, so nominal energization parameters do not directly represent the interfacial electrical state. GCr15 ball-on-disk tests compared dry and polyalphaolefin (PAO 40)-lubricated conditions at 6 N under 5 V, 1 Hz switching. Tests covered nominal duty cycles from D = 0 to 1.00, where D is the ratio of the voltage on-time to the voltage period. Equal-on-time friction tests compared periodic D = 0.50, on→off and off→on. Wear was compared among periodic D = 0.50, off→on, and continuous direct current (DC). Friction increased overall with D. Longer on-time prolonged concurrent microcontact Joule heating and mechanical friction. Dry-sliding wear volume varied non-monotonically, peaking at D = 0.50 with changes in surface-layer removal and O-containing debris retention. Under PAO 40 boundary/mixed lubrication, wear-track width and volume increased monotonically with electrical-heating-related changes in oil film support and separation, microcontact, plowing, and plastic deformation. Equal-on-time friction histories differed. Periodic D = 0.50 and off→on produced similar wear volumes but different morphologies. Dry off→on and continuous DC wear volumes were close. Wear depended on timing and interface state at energization. Interface evolution altered contact resistance and voltage division, feeding back on wear. These findings support energization-parameter and bearing wear risk assessment under intermittent source-side excitation.
- 5 September 2026
- Published by Elsevier in Tribology International
- Vol. 226
Research on optical interferometry-based real-time monitoring and mechanism analysis in intermittent motion wear
- 5 September 2026
- Published by Elsevier in Tribology International
- Vol. 226
Research on optical interferometry-based real-time monitoring and mechanism analysis in intermittent motion wear
- 18 December 2025
- Published by Elsevier in Tribology International
- Vol. 216
Shear-thinning enhancement of 2D nano-materials in EHL contact driven by composite slips
- 18 December 2025
- Published by Elsevier in Tribology International
- Vol. 216
Shear-thinning enhancement of 2D nano-materials in EHL contact driven by composite slips
- Open Access
- 4 August 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (8) , 279
Effect of Grease Composition on Impact-Sliding Wear
Impact-sliding experiments were performed by using four self-made lithium-based greases, namely Yangtze Grease 1, Yangtze Grease 2, Yangtze Grease 3, and Yangtze Grease 4. The influence of base oil viscosity, thickener content, and morphology of thickener fiber clusters on the lubricating state were visually explored, combined with field-emission microscopy and two-light interference technology. The grease film distribution at the middle section was measured using Dichromatic Interference Intensity Modulation (DIIM) software. All experiments were executed in a completely flooded environment. The results show that among the components of grease, the base oil’s viscosity has the greatest impact on the anti-wear performance of the grease. As the viscosity of the base oil increases, the grease exhibits better anti-wear performance. The grease film thickness under the condition of high-viscosity base oil is about 10 times higher than that under the condition of low-viscosity base oil. Secondly, the content of thickener in the grease needs to be controlled within a reasonable range. The experiments indicate that the effect of thickener content on the grease’s film-forming properties becomes more pronounced at higher speeds. From the experiment using YG 4, it can be seen that a higher thickener content under high-speed conditions increases the thickness of the lubricating grease film by about 10 times. The dimensions of the thickener fibers and the density of their entanglement structure significantly influence the rheological properties and load-bearing capacity of the grease. Larger fiber sizes and higher entanglement densities result in reduced grease fluidity and recovery but enhance its load-bearing capabilities. In order to obtain the best anti-wear performance during impact-sliding motion, the size of the thickener fiber and the density of the entanglement structure need to be controlled within an appropriate range.
- 4 August 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (8) , 279
Open AccessEffect of Grease Composition on Impact-Sliding Wear
Impact-sliding experiments were performed by using four self-made lithium-based greases, namely Yangtze Grease 1, Yangtze Grease 2, Yangtze Grease 3, and Yangtze Grease 4. The influence of base oil viscosity, thickener content, and morphology of thickener fiber clusters on the lubricating state were visually explored, combined with field-emission microscopy and two-light interference technology. The grease film distribution at the middle section was measured using Dichromatic Interference Intensity Modulation (DIIM) software. All experiments were executed in a completely flooded environment. The results show that among the components of grease, the base oil’s viscosity has the greatest impact on the anti-wear performance of the grease. As the viscosity of the base oil increases, the grease exhibits better anti-wear performance. The grease film thickness under the condition of high-viscosity base oil is about 10 times higher than that under the condition of low-viscosity base oil. Secondly, the content of thickener in the grease needs to be controlled within a reasonable range. The experiments indicate that the effect of thickener content on the grease’s film-forming properties becomes more pronounced at higher speeds. From the experiment using YG 4, it can be seen that a higher thickener content under high-speed conditions increases the thickness of the lubricating grease film by about 10 times. The dimensions of the thickener fibers and the density of their entanglement structure significantly influence the rheological properties and load-bearing capacity of the grease. Larger fiber sizes and higher entanglement densities result in reduced grease fluidity and recovery but enhance its load-bearing capabilities. In order to obtain the best anti-wear performance during impact-sliding motion, the size of the thickener fiber and the density of the entanglement structure need to be controlled within an appropriate range.