Jan Białasik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jan Białasik has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Alireza Tabrizikahou
Institute of Building Engineering, Poznań University of Technology, Poznan, Poland, Poland
4 shared publications - Dominika Samulczyk
Institute of Building Engineering, Poznan University of Technology, Piotrowo 5, 60-965 Poznan, Poland
2 shared publications - Magdalena Łasecka-Plura
Institute of Structural Analysis, Poznan University of Technology, Piotrowo 5, 60-965 Poznań, Poland
2 shared publications - Mieczysław Kuczma
Institute of Building Engineering, Poznan University of Technology, Piotrowo 5, 60-965 Poznan, Poland
2 shared publications - Tomasz Jankowiak
Institute of Structural Analysis, Poznan University of Technology, Piotrowo 5, 60-965 Poznań, Poland
2 shared publications - Wojciech Podraza
Institute of Building Engineering, Poznan University of Technology, Piotrowo 5, 60-965 Poznan, Poland
2 shared publications
Latest Publications
- Open Access
Electrical Resistance Activation of Embedded Fe-SMA Rebars in Pre-Cracked UHPFRC Beams: Internal Temperature Evolution and Calibrated Electro-Thermal Simulation
Iron-based shape memory alloy (Fe–SMA) rebars can generate internal prestress in cement-based members after restrained thermal activation; however, the temperature actually reached by embedded rebars in cracked UHPFRC is difficult to infer from exposed bar segments. This study investigates electrical resistance activation of 4% prestrained Fe–SMA rebars embedded in pre-cracked UHPFRC beams and clarifies the activation-control problem by combining thermocouple measurements with a calibrated two-dimensional electro-thermal simulator. Twelve beams (150 × 150 × 600 mm) containing either Dramix 3D or Dramix 4D hooked steel fibers were first loaded in three-point bending to a mid-span displacement of 4 mm. The 4D series reached a 9.47% higher average pre-cracking load, confirming that fiber geometry modified the cracked state before heating. During activation, the exposed rebar segment reached 200 °C after approximately 77 s, whereas the embedded working segment reached the same target only after approximately 213 s; at that moment, the exposed segment was already close to 350 °C. The calibrated simulator reproduced the target activation time with an error of approximately 3 s and visualized the localized heat transfer from Fe–SMA to UHPFRC. The results demonstrate that activation control based only on exposed-bar temperature may cause under-activation of the embedded reinforcement, and that direct internal temperature monitoring is required for reliable Fe–SMA activation in cracked UHPFRC members.
Open AccessElectrical Resistance Activation of Embedded Fe-SMA Rebars in Pre-Cracked UHPFRC Beams: Internal Temperature Evolution and Calibrated Electro-Thermal Simulation
Iron-based shape memory alloy (Fe–SMA) rebars can generate internal prestress in cement-based members after restrained thermal activation; however, the temperature actually reached by embedded rebars in cracked UHPFRC is difficult to infer from exposed bar segments. This study investigates electrical resistance activation of 4% prestrained Fe–SMA rebars embedded in pre-cracked UHPFRC beams and clarifies the activation-control problem by combining thermocouple measurements with a calibrated two-dimensional electro-thermal simulator. Twelve beams (150 × 150 × 600 mm) containing either Dramix 3D or Dramix 4D hooked steel fibers were first loaded in three-point bending to a mid-span displacement of 4 mm. The 4D series reached a 9.47% higher average pre-cracking load, confirming that fiber geometry modified the cracked state before heating. During activation, the exposed rebar segment reached 200 °C after approximately 77 s, whereas the embedded working segment reached the same target only after approximately 213 s; at that moment, the exposed segment was already close to 350 °C. The calibrated simulator reproduced the target activation time with an error of approximately 3 s and visualized the localized heat transfer from Fe–SMA to UHPFRC. The results demonstrate that activation control based only on exposed-bar temperature may cause under-activation of the embedded reinforcement, and that direct internal temperature monitoring is required for reliable Fe–SMA activation in cracked UHPFRC members.
- Open Access
Synergistic Effects of Fiber Inclination, Geometry, and Thermal Treatment on Fe-SMA Fiber Pull-Out Resistance in High-Performance Concrete
Iron-based shape memory alloy (Fe-SMA) fibers can enhance cementitious composites through both crack bridging and thermally activated recovery stresses. Since fiber pull-out governs load transfer at the micro scale, understanding the combined effects of fiber geometry, inclination, and thermal treatment is essential. This study experimentally investigated the pull-out behavior of hooked-end Fe-SMA fibers embedded in high-performance concrete (HPC). A total of 54 ASTM C307-type briquette specimens were tested using single-hook (3D) and double-hook (4D) fibers at inclination angles of 60°, 75°, and 90° under ambient, 100 °C, and 200 °C conditions. Additional flexural, compressive, and direct tensile tests were conducted on plain HPC exposed to the same thermal regime. At ambient temperature, 4D fibers showed 50–70% higher peak pull-out forces than 3D fibers. Heating to 100 °C further increased pull-out resistance by about 6–17%, and the 4D-60-100 configuration achieved the highest performance. In contrast, exposure to 200 °C reduced pull-out resistance by about 5–12% below ambient values. Overall, a 60° inclination generally provided a better response, while 90° produced the lowest. The results confirm that moderate thermal activation combined with double-hook geometry is the most effective strategy for maximizing Fe-SMA fiber–matrix load transfer in HPC.
Open AccessSynergistic Effects of Fiber Inclination, Geometry, and Thermal Treatment on Fe-SMA Fiber Pull-Out Resistance in High-Performance Concrete
Iron-based shape memory alloy (Fe-SMA) fibers can enhance cementitious composites through both crack bridging and thermally activated recovery stresses. Since fiber pull-out governs load transfer at the micro scale, understanding the combined effects of fiber geometry, inclination, and thermal treatment is essential. This study experimentally investigated the pull-out behavior of hooked-end Fe-SMA fibers embedded in high-performance concrete (HPC). A total of 54 ASTM C307-type briquette specimens were tested using single-hook (3D) and double-hook (4D) fibers at inclination angles of 60°, 75°, and 90° under ambient, 100 °C, and 200 °C conditions. Additional flexural, compressive, and direct tensile tests were conducted on plain HPC exposed to the same thermal regime. At ambient temperature, 4D fibers showed 50–70% higher peak pull-out forces than 3D fibers. Heating to 100 °C further increased pull-out resistance by about 6–17%, and the 4D-60-100 configuration achieved the highest performance. In contrast, exposure to 200 °C reduced pull-out resistance by about 5–12% below ambient values. Overall, a 60° inclination generally provided a better response, while 90° produced the lowest. The results confirm that moderate thermal activation combined with double-hook geometry is the most effective strategy for maximizing Fe-SMA fiber–matrix load transfer in HPC.
- Open Access
Numerical Analysis of Bifacial Photovoltaic Panels Subjected to Repeated Loading
This study investigates the mechanical response of bifacial glass–glass photovoltaic modules subjected to snow-type loading, with a particular focus on the influence of silicon cell spacing on global deformation and local stress distributions in the silicon cell layer and the adhesive layer. Five computational finite element models were developed which explicitly represent all laminate layers and discrete cell layout. The numerical results are interpreted within the framework of partial interaction and shear transfer between the glass plies and are validated against previously obtained home conducted experimental observations. The results demonstrate that a silicon cell layout has a pronounced effect on local tensile stresses in silicon cells and on the curvature distribution within the laminate, while its influence on the global kinematic response is less critical. The numerical analysis indicates that the relative displacements between the glass layers resulting from the flexibility of the adhesive bond play a critical role.
Open AccessNumerical Analysis of Bifacial Photovoltaic Panels Subjected to Repeated Loading
This study investigates the mechanical response of bifacial glass–glass photovoltaic modules subjected to snow-type loading, with a particular focus on the influence of silicon cell spacing on global deformation and local stress distributions in the silicon cell layer and the adhesive layer. Five computational finite element models were developed which explicitly represent all laminate layers and discrete cell layout. The numerical results are interpreted within the framework of partial interaction and shear transfer between the glass plies and are validated against previously obtained home conducted experimental observations. The results demonstrate that a silicon cell layout has a pronounced effect on local tensile stresses in silicon cells and on the curvature distribution within the laminate, while its influence on the global kinematic response is less critical. The numerical analysis indicates that the relative displacements between the glass layers resulting from the flexibility of the adhesive bond play a critical role.
- Open Access
- 19 March 2026
- Published by MDPI AG in Preprints.org
Synergistic Effects of Fiber Inclination, Geometry, and Thermal Treatment on Fe-SMA Fiber Pullout Resistance in High-Performance Concrete
Iron-based shape memory alloy (Fe-SMA) fibers can enhance cementitious composites through both crack-bridging and thermally activated recovery stresses. Since fiber pull-out governs load transfer at the microscale, understanding the combined effects of fiber geometry, inclination, and thermal treatment is essential. This study experimentally investigated the pull-out behavior of hooked-end Fe-SMA fibers embedded in high-performance concrete (HPC). A total of 54 ASTM C307-type briquette specimens were tested using single-hook (3D) and double-hook (4D) fibers at inclination angles of 60∘, 75∘, and 90∘ under ambient, 100 ∘C, and 200 ∘C conditions. Additional flexural, compressive, and direct tensile tests were conducted on plain HPC exposed to the same thermal regime. At ambient temperature, 4D fibers showed 50–70% higher peak pull-out forces than 3D fibers. Heating to 100 ∘C further increased pull-out resistance by about 6–17%, and the 4D-60-100 configuration achieved the highest performance. In contrast, exposure to 200 ∘C reduced pull-out resistance by about 5–12% below ambient values. Overall, a 60∘ inclination generally provided the best response, while 90∘ produced the lowest. The results confirm that moderate thermal activation combined with double-hook geometry is the most effective strategy for maximizing Fe-SMA fiber–matrix load transfer in HPC.
- 19 March 2026
- Published by MDPI AG in Preprints.org
Open AccessSynergistic Effects of Fiber Inclination, Geometry, and Thermal Treatment on Fe-SMA Fiber Pullout Resistance in High-Performance Concrete
Iron-based shape memory alloy (Fe-SMA) fibers can enhance cementitious composites through both crack-bridging and thermally activated recovery stresses. Since fiber pull-out governs load transfer at the microscale, understanding the combined effects of fiber geometry, inclination, and thermal treatment is essential. This study experimentally investigated the pull-out behavior of hooked-end Fe-SMA fibers embedded in high-performance concrete (HPC). A total of 54 ASTM C307-type briquette specimens were tested using single-hook (3D) and double-hook (4D) fibers at inclination angles of 60∘, 75∘, and 90∘ under ambient, 100 ∘C, and 200 ∘C conditions. Additional flexural, compressive, and direct tensile tests were conducted on plain HPC exposed to the same thermal regime. At ambient temperature, 4D fibers showed 50–70% higher peak pull-out forces than 3D fibers. Heating to 100 ∘C further increased pull-out resistance by about 6–17%, and the 4D-60-100 configuration achieved the highest performance. In contrast, exposure to 200 ∘C reduced pull-out resistance by about 5–12% below ambient values. Overall, a 60∘ inclination generally provided the best response, while 90∘ produced the lowest. The results confirm that moderate thermal activation combined with double-hook geometry is the most effective strategy for maximizing Fe-SMA fiber–matrix load transfer in HPC.
- Open Access
- 26 February 2026
- Published by MDPI AG in Preprints.org
Numerical Analysis of Bifacial Photovoltaic Panels Subjected to Repeated Loading
This study investigates the mechanical response of bifacial glass-glass photovoltaic modules subjected to snow-type loading, with a particular focus on the influence of silicon cell spacing on global deformation and local stress distributions in the silicon layer. Five computational finite element models were developed which explicitly represent all laminate layers and discrete cell layout. The numerical results are interpreted within the framework of partial interaction and shear transfer between the glass plies, and are validated against previously obtained home conducted experimental observations. The results demonstrate that silicon cell layout has a pronounced effect on local tensile stresses in silicon cells and on the curvature distribution within the laminate, while its influence on the global kinematic response is less critical. The numerical analysis indicates that the relative displacements between the glass layers resulting from the flexibility of the adhesive bond play a critical role.
- 26 February 2026
- Published by MDPI AG in Preprints.org
Open AccessNumerical Analysis of Bifacial Photovoltaic Panels Subjected to Repeated Loading
This study investigates the mechanical response of bifacial glass-glass photovoltaic modules subjected to snow-type loading, with a particular focus on the influence of silicon cell spacing on global deformation and local stress distributions in the silicon layer. Five computational finite element models were developed which explicitly represent all laminate layers and discrete cell layout. The numerical results are interpreted within the framework of partial interaction and shear transfer between the glass plies, and are validated against previously obtained home conducted experimental observations. The results demonstrate that silicon cell layout has a pronounced effect on local tensile stresses in silicon cells and on the curvature distribution within the laminate, while its influence on the global kinematic response is less critical. The numerical analysis indicates that the relative displacements between the glass layers resulting from the flexibility of the adhesive bond play a critical role.