Jiawen Liu
Research Subjects
Jiawen Liu has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Jian Meng
Kunming Engineering & Research Institute of Nonferrous Metallurgy Co., Ltd., Kunming 650032, China
2 shared publications - Kegang Li
Kunming University of Science and Technology
2 shared publications - Tianlong Zhou
Faculty of Land Resources Engineering, Kunming University of Science and Technology, Kunming 650093, China
2 shared publications - Dong Tian
Faculty of Land Resource Engineering, Kunming University of Science and Technology, Kunming 650093, China
1 shared publication - Han Zhou
Faculty of Land Resources Engineering, Kunming University of Science and Technology, Kunming 650093, China
1 shared publication - Mingliang Li
Faculty of Land Resources Engineering, Kunming University of Science and Technology, Kunming 650093, China
1 shared publication
Latest Publications
- Open Access
- 13 August 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (8) , 330
Experimental Investigation and Numerical Simulation on the Strength and Deformation Characteristics of Granular Materials at Various Elevations of Dump Slope
Determining the shear strength parameters of granular materials in high waste rock dump slopes is essential for reliable slope stability analysis. In this study, dump materials were sampled from six benches (elevations 2800–2950 m) of an open-pit mine dump slope, and in situ density tests, gradation analyses, and large-scale consolidated drained (CD) triaxial tests were performed. Two PFC2D slope models—one with uniform (spatially averaged) parameters and one with elevation-dependent (layered) parameters—were then established to quantify how spatial heterogeneity affects stability predictions. The results show pronounced vertical heterogeneity: density, porosity, gradation, and shear strength parameters vary systematically among benches, reflecting the combined effects of compaction history and particle segregation during dumping. All specimens exhibited strain hardening and continuous shear contraction, and specimens with a denser, better-graded structure showed higher strength and lower compressibility. The layered model yields a higher factor of safety and shallower, bench-scale slip surfaces, whereas the uniform model underestimates stability and misplaces the critical slip zones. These findings demonstrate that elevation-dependent parameter assignment better represents the heterogeneous failure mechanism of high dump slopes and should be preferred over uniform parameterization in stability analyses of similar waste rock dumps.
- 13 August 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (8) , 330
Open AccessExperimental Investigation and Numerical Simulation on the Strength and Deformation Characteristics of Granular Materials at Various Elevations of Dump Slope
Determining the shear strength parameters of granular materials in high waste rock dump slopes is essential for reliable slope stability analysis. In this study, dump materials were sampled from six benches (elevations 2800–2950 m) of an open-pit mine dump slope, and in situ density tests, gradation analyses, and large-scale consolidated drained (CD) triaxial tests were performed. Two PFC2D slope models—one with uniform (spatially averaged) parameters and one with elevation-dependent (layered) parameters—were then established to quantify how spatial heterogeneity affects stability predictions. The results show pronounced vertical heterogeneity: density, porosity, gradation, and shear strength parameters vary systematically among benches, reflecting the combined effects of compaction history and particle segregation during dumping. All specimens exhibited strain hardening and continuous shear contraction, and specimens with a denser, better-graded structure showed higher strength and lower compressibility. The layered model yields a higher factor of safety and shallower, bench-scale slip surfaces, whereas the uniform model underestimates stability and misplaces the critical slip zones. These findings demonstrate that elevation-dependent parameter assignment better represents the heterogeneous failure mechanism of high dump slopes and should be preferred over uniform parameterization in stability analyses of similar waste rock dumps.
- Open Access
Analysis of the Influence of Gradation Difference on the Stability of Dump Slope Based on Triaxial Test and Numerical Simulation
Instability in dump slopes frequently induces landslides, a process governed by complex factors. To investigate the impact of gradation composition on dump slope stability, four distinct gradations were designed, and large-scale laboratory triaxial tests were conducted to characterize their strength and deformation behaviors under varying confining pressures. Concurrently, numerical models of dump slopes with these four gradations were established using Particle Flow Code (PFC) to simulate rainfall infiltration processes. Through a comparative analysis of particle contact force chains, pore water pressure evolution, particle displacement under varying rainfall durations, and safety factors under natural and rainfall conditions, the mechanisms governing the influence of gradation composition on slope stability were elucidated from both macroscopic and microscopic perspectives. Results indicate the following: (1) Gradation composition significantly affects the strength and deformation characteristics of dump materials. Sample group 3 (with a fine-to-coarse particle ratio of 4:6) exhibited the highest strength among the four test samples, with peak deviatoric stresses of 610 kPa, 1075 kPa, and 1539 kPa under confining pressures of 200 kPa, 400 kPa, and 600 kPa, respectively. Its corresponding shear strength parameters were a cohesion of 38.45 kPa and an internal friction angle of 32.55°. In contrast, sample group 4 (fine-to-coarse ratio of 6:4) showed the lowest strength, with peak deviatoric stresses of 489 kPa, 840 kPa, and 1290 kPa under the same confining pressures, and shear strength parameters of c = 25.35 kPa and φ = 30.02°. (2) Gradation modulates contact forces and failure modes via a “skeleton-filling” mechanism. (3) Gradation plays a critical role in controlling pore water pressure evolution and the seepage characteristics of the dump slope model. Among the four designed gradations and their corresponding numerical models, Model 3 was characterized by the highest contact forces and the lowest pore water pressure. It exhibited the highest stability under both natural and rainfall conditions, with safety factors of 1.70 and 1.22, respectively. Conversely, Model 4 showed weak particle contact forces and high pore pressure, demonstrating the poorest stability. It yielded safety factors of only 1.25 and 1.02 under natural and rainfall-saturated conditions, indicating that it represents the least favorable gradation composition. These findings provide valuable references for the optimization of dumping processes and stability control in similar engineering projects.
Open AccessAnalysis of the Influence of Gradation Difference on the Stability of Dump Slope Based on Triaxial Test and Numerical Simulation
Instability in dump slopes frequently induces landslides, a process governed by complex factors. To investigate the impact of gradation composition on dump slope stability, four distinct gradations were designed, and large-scale laboratory triaxial tests were conducted to characterize their strength and deformation behaviors under varying confining pressures. Concurrently, numerical models of dump slopes with these four gradations were established using Particle Flow Code (PFC) to simulate rainfall infiltration processes. Through a comparative analysis of particle contact force chains, pore water pressure evolution, particle displacement under varying rainfall durations, and safety factors under natural and rainfall conditions, the mechanisms governing the influence of gradation composition on slope stability were elucidated from both macroscopic and microscopic perspectives. Results indicate the following: (1) Gradation composition significantly affects the strength and deformation characteristics of dump materials. Sample group 3 (with a fine-to-coarse particle ratio of 4:6) exhibited the highest strength among the four test samples, with peak deviatoric stresses of 610 kPa, 1075 kPa, and 1539 kPa under confining pressures of 200 kPa, 400 kPa, and 600 kPa, respectively. Its corresponding shear strength parameters were a cohesion of 38.45 kPa and an internal friction angle of 32.55°. In contrast, sample group 4 (fine-to-coarse ratio of 6:4) showed the lowest strength, with peak deviatoric stresses of 489 kPa, 840 kPa, and 1290 kPa under the same confining pressures, and shear strength parameters of c = 25.35 kPa and φ = 30.02°. (2) Gradation modulates contact forces and failure modes via a “skeleton-filling” mechanism. (3) Gradation plays a critical role in controlling pore water pressure evolution and the seepage characteristics of the dump slope model. Among the four designed gradations and their corresponding numerical models, Model 3 was characterized by the highest contact forces and the lowest pore water pressure. It exhibited the highest stability under both natural and rainfall conditions, with safety factors of 1.70 and 1.22, respectively. Conversely, Model 4 showed weak particle contact forces and high pore pressure, demonstrating the poorest stability. It yielded safety factors of only 1.25 and 1.02 under natural and rainfall-saturated conditions, indicating that it represents the least favorable gradation composition. These findings provide valuable references for the optimization of dumping processes and stability control in similar engineering projects.