Jian Meng
Research Subjects
Jian Meng has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Han Zhou
Faculty of Land Resources Engineering, Kunming University of Science and Technology, Kunming 650093, China
3 shared publications - Jiawen Liu
Kunming Engineering & Research Institute of Nonferrous Metallurgy Co., Ltd., Kunming 650032, China
2 shared publications - Jiawen Liu
Kunming Engineering & Research Institute of Nonferrous Metallurgy Co., Ltd., Kunming 650032, China
2 shared publications - Kegang Li
Kunming University of Science and Technology
2 shared publications - Tianlong Zhou
Faculty of Land Resources Engineering, Kunming University of Science and Technology, Kunming 650093, China
2 shared publications - An Chen
Faculty of Land Resources Engineering, Kunming University of Science and Technology, Kunming 650093, China
1 shared publication
Latest Publications
- Open Access
- 13 August 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (8) , 330
Experimental Investigation and Numerical Simulation on the Strength and Deformation Characteristics of Granular Materials at Various Elevations of Dump Slope
Determining the shear strength parameters of granular materials in high waste rock dump slopes is essential for reliable slope stability analysis. In this study, dump materials were sampled from six benches (elevations 2800–2950 m) of an open-pit mine dump slope, and in situ density tests, gradation analyses, and large-scale consolidated drained (CD) triaxial tests were performed. Two PFC2D slope models—one with uniform (spatially averaged) parameters and one with elevation-dependent (layered) parameters—were then established to quantify how spatial heterogeneity affects stability predictions. The results show pronounced vertical heterogeneity: density, porosity, gradation, and shear strength parameters vary systematically among benches, reflecting the combined effects of compaction history and particle segregation during dumping. All specimens exhibited strain hardening and continuous shear contraction, and specimens with a denser, better-graded structure showed higher strength and lower compressibility. The layered model yields a higher factor of safety and shallower, bench-scale slip surfaces, whereas the uniform model underestimates stability and misplaces the critical slip zones. These findings demonstrate that elevation-dependent parameter assignment better represents the heterogeneous failure mechanism of high dump slopes and should be preferred over uniform parameterization in stability analyses of similar waste rock dumps.
- 13 August 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (8) , 330
Open AccessExperimental Investigation and Numerical Simulation on the Strength and Deformation Characteristics of Granular Materials at Various Elevations of Dump Slope
Determining the shear strength parameters of granular materials in high waste rock dump slopes is essential for reliable slope stability analysis. In this study, dump materials were sampled from six benches (elevations 2800–2950 m) of an open-pit mine dump slope, and in situ density tests, gradation analyses, and large-scale consolidated drained (CD) triaxial tests were performed. Two PFC2D slope models—one with uniform (spatially averaged) parameters and one with elevation-dependent (layered) parameters—were then established to quantify how spatial heterogeneity affects stability predictions. The results show pronounced vertical heterogeneity: density, porosity, gradation, and shear strength parameters vary systematically among benches, reflecting the combined effects of compaction history and particle segregation during dumping. All specimens exhibited strain hardening and continuous shear contraction, and specimens with a denser, better-graded structure showed higher strength and lower compressibility. The layered model yields a higher factor of safety and shallower, bench-scale slip surfaces, whereas the uniform model underestimates stability and misplaces the critical slip zones. These findings demonstrate that elevation-dependent parameter assignment better represents the heterogeneous failure mechanism of high dump slopes and should be preferred over uniform parameterization in stability analyses of similar waste rock dumps.
- Open Access
Modification of Rock Stress Factor for the Mathews Stability Graph Method Based on Hoek–Brown Criterion and Its Application
During underground mining, stope stability is affected by excavation-induced stress redistribution and nonlinear degradation of rock mass strength. The conventional Mathews stability graph method employs an empirical stress factor A, which does not explicitly consider the nonlinear relationship between stress conditions and rock mass strength. In this study, the generalized Hoek–Brown criterion was introduced to define the maximum stress factor (MSF), and a modified stress factor A′ was developed by considering tensile and shear failure mechanisms. The proposed method incorporates the nonlinear stress–stability relationship of underground stopes and improves the reliability of stability assessment. A copper mine in southwest China was selected as a case study. The rock mass quality indices and stress parameters of ten representative stopes were obtained through field investigations, stope roof stress measurements, discontinuity surveys, and laboratory tests. The modified stress factor A′ was incorporated into the Mathews stability graph to account for excavation-induced stress redistribution and rock mass strength degradation. Compared with the conventional method, the modified approach generally reduced the stability numbers of the investigated stopes, with an average reduction of approximately 25.6% (excluding D1780-1, where the confinement strengthening effect resulted in a slight increase in stability number). The revised stability classifications show good consistency with the FLAC3D simulation results and field observations, providing supporting evidence for the application of the proposed method to underground stope stability assessment in the studied mine.
Open AccessModification of Rock Stress Factor for the Mathews Stability Graph Method Based on Hoek–Brown Criterion and Its Application
During underground mining, stope stability is affected by excavation-induced stress redistribution and nonlinear degradation of rock mass strength. The conventional Mathews stability graph method employs an empirical stress factor A, which does not explicitly consider the nonlinear relationship between stress conditions and rock mass strength. In this study, the generalized Hoek–Brown criterion was introduced to define the maximum stress factor (MSF), and a modified stress factor A′ was developed by considering tensile and shear failure mechanisms. The proposed method incorporates the nonlinear stress–stability relationship of underground stopes and improves the reliability of stability assessment. A copper mine in southwest China was selected as a case study. The rock mass quality indices and stress parameters of ten representative stopes were obtained through field investigations, stope roof stress measurements, discontinuity surveys, and laboratory tests. The modified stress factor A′ was incorporated into the Mathews stability graph to account for excavation-induced stress redistribution and rock mass strength degradation. Compared with the conventional method, the modified approach generally reduced the stability numbers of the investigated stopes, with an average reduction of approximately 25.6% (excluding D1780-1, where the confinement strengthening effect resulted in a slight increase in stability number). The revised stability classifications show good consistency with the FLAC3D simulation results and field observations, providing supporting evidence for the application of the proposed method to underground stope stability assessment in the studied mine.
- Open Access
- 2 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (7) , 3445
Calculation Method of Foundation Bearing Capacity of Waste Dumps Based on Boussinesq Equation
The insufficient bearing capacity of the foundation at waste dumps can easily lead to landslides and other geohazards. At present, discrepancies between the calculated bearing capacity of such foundations and actual field performance are a major cause of these accidents. Therefore, further research into methods for accurately estimating the foundation bearing capacity of waste dumps to guide engineering practice is crucial for preventing such incidents. This study employs a combination of theoretical and case analysis to examine the current calculation methods. We discover that the calculated values are smaller than the actual values. Moreover, by taking into account both the upper load of the waste dumps and the bearing capacity of the lower foundation, we analyzed the main problems leading to the underestimation. In response to the aforementioned issues, this study suggests incorporating the Boussinesq equation into the calculation of the upper load to account for the load distribution across various slope forms and the diffusion and superposition of stress at different foundation positions and depths. Simultaneously, the foundation’s bearing capacity is calculated to increase with burial depth, aligning with the stress at different positions. Finally, a new method for calculating the bearing capacity of foundations at waste dumps was developed. The bearing capacities of the waste dump foundation and the weakest point determined using the proposed method are validated through a case study and FLAC3D numerical simulation. This study can provide a reference for calculating the bearing capacity of foundations in similar waste dumps.
- 2 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (7) , 3445
Open AccessCalculation Method of Foundation Bearing Capacity of Waste Dumps Based on Boussinesq Equation
The insufficient bearing capacity of the foundation at waste dumps can easily lead to landslides and other geohazards. At present, discrepancies between the calculated bearing capacity of such foundations and actual field performance are a major cause of these accidents. Therefore, further research into methods for accurately estimating the foundation bearing capacity of waste dumps to guide engineering practice is crucial for preventing such incidents. This study employs a combination of theoretical and case analysis to examine the current calculation methods. We discover that the calculated values are smaller than the actual values. Moreover, by taking into account both the upper load of the waste dumps and the bearing capacity of the lower foundation, we analyzed the main problems leading to the underestimation. In response to the aforementioned issues, this study suggests incorporating the Boussinesq equation into the calculation of the upper load to account for the load distribution across various slope forms and the diffusion and superposition of stress at different foundation positions and depths. Simultaneously, the foundation’s bearing capacity is calculated to increase with burial depth, aligning with the stress at different positions. Finally, a new method for calculating the bearing capacity of foundations at waste dumps was developed. The bearing capacities of the waste dump foundation and the weakest point determined using the proposed method are validated through a case study and FLAC3D numerical simulation. This study can provide a reference for calculating the bearing capacity of foundations in similar waste dumps.
- Open Access
Analysis of the Influence of Gradation Difference on the Stability of Dump Slope Based on Triaxial Test and Numerical Simulation
Instability in dump slopes frequently induces landslides, a process governed by complex factors. To investigate the impact of gradation composition on dump slope stability, four distinct gradations were designed, and large-scale laboratory triaxial tests were conducted to characterize their strength and deformation behaviors under varying confining pressures. Concurrently, numerical models of dump slopes with these four gradations were established using Particle Flow Code (PFC) to simulate rainfall infiltration processes. Through a comparative analysis of particle contact force chains, pore water pressure evolution, particle displacement under varying rainfall durations, and safety factors under natural and rainfall conditions, the mechanisms governing the influence of gradation composition on slope stability were elucidated from both macroscopic and microscopic perspectives. Results indicate the following: (1) Gradation composition significantly affects the strength and deformation characteristics of dump materials. Sample group 3 (with a fine-to-coarse particle ratio of 4:6) exhibited the highest strength among the four test samples, with peak deviatoric stresses of 610 kPa, 1075 kPa, and 1539 kPa under confining pressures of 200 kPa, 400 kPa, and 600 kPa, respectively. Its corresponding shear strength parameters were a cohesion of 38.45 kPa and an internal friction angle of 32.55°. In contrast, sample group 4 (fine-to-coarse ratio of 6:4) showed the lowest strength, with peak deviatoric stresses of 489 kPa, 840 kPa, and 1290 kPa under the same confining pressures, and shear strength parameters of c = 25.35 kPa and φ = 30.02°. (2) Gradation modulates contact forces and failure modes via a “skeleton-filling” mechanism. (3) Gradation plays a critical role in controlling pore water pressure evolution and the seepage characteristics of the dump slope model. Among the four designed gradations and their corresponding numerical models, Model 3 was characterized by the highest contact forces and the lowest pore water pressure. It exhibited the highest stability under both natural and rainfall conditions, with safety factors of 1.70 and 1.22, respectively. Conversely, Model 4 showed weak particle contact forces and high pore pressure, demonstrating the poorest stability. It yielded safety factors of only 1.25 and 1.02 under natural and rainfall-saturated conditions, indicating that it represents the least favorable gradation composition. These findings provide valuable references for the optimization of dumping processes and stability control in similar engineering projects.
Open AccessAnalysis of the Influence of Gradation Difference on the Stability of Dump Slope Based on Triaxial Test and Numerical Simulation
Instability in dump slopes frequently induces landslides, a process governed by complex factors. To investigate the impact of gradation composition on dump slope stability, four distinct gradations were designed, and large-scale laboratory triaxial tests were conducted to characterize their strength and deformation behaviors under varying confining pressures. Concurrently, numerical models of dump slopes with these four gradations were established using Particle Flow Code (PFC) to simulate rainfall infiltration processes. Through a comparative analysis of particle contact force chains, pore water pressure evolution, particle displacement under varying rainfall durations, and safety factors under natural and rainfall conditions, the mechanisms governing the influence of gradation composition on slope stability were elucidated from both macroscopic and microscopic perspectives. Results indicate the following: (1) Gradation composition significantly affects the strength and deformation characteristics of dump materials. Sample group 3 (with a fine-to-coarse particle ratio of 4:6) exhibited the highest strength among the four test samples, with peak deviatoric stresses of 610 kPa, 1075 kPa, and 1539 kPa under confining pressures of 200 kPa, 400 kPa, and 600 kPa, respectively. Its corresponding shear strength parameters were a cohesion of 38.45 kPa and an internal friction angle of 32.55°. In contrast, sample group 4 (fine-to-coarse ratio of 6:4) showed the lowest strength, with peak deviatoric stresses of 489 kPa, 840 kPa, and 1290 kPa under the same confining pressures, and shear strength parameters of c = 25.35 kPa and φ = 30.02°. (2) Gradation modulates contact forces and failure modes via a “skeleton-filling” mechanism. (3) Gradation plays a critical role in controlling pore water pressure evolution and the seepage characteristics of the dump slope model. Among the four designed gradations and their corresponding numerical models, Model 3 was characterized by the highest contact forces and the lowest pore water pressure. It exhibited the highest stability under both natural and rainfall conditions, with safety factors of 1.70 and 1.22, respectively. Conversely, Model 4 showed weak particle contact forces and high pore pressure, demonstrating the poorest stability. It yielded safety factors of only 1.25 and 1.02 under natural and rainfall-saturated conditions, indicating that it represents the least favorable gradation composition. These findings provide valuable references for the optimization of dumping processes and stability control in similar engineering projects.