Han Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Han Zhou has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Jian Meng
Kunming Engineering & Research Institute of Nonferrous Metallurgy Co., Ltd., Kunming 650032, China
3 shared publications - Jiawen Liu
Kunming Engineering & Research Institute of Nonferrous Metallurgy Co., Ltd., Kunming 650032, China
2 shared publications - An Chen
Faculty of Land Resources Engineering, Kunming University of Science and Technology, Kunming 650093, China
1 shared publication - Dacheng Lu
Kunming Engineering & Research Institute of Nonferrous Metallurgy Co., Ltd., Kunming 650032, China
1 shared publication - Jiawen Liu
Kunming Engineering & Research Institute of Nonferrous Metallurgy Co., Ltd., Kunming 650032, China
1 shared publication - Jun Fu
Faculty of Land Resources Engineering, Kunming University of Science and Technology, Kunming 650093, China
1 shared publication
Latest Publications
- Open Access
- 13 August 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (8) , 330
Experimental Investigation and Numerical Simulation on the Strength and Deformation Characteristics of Granular Materials at Various Elevations of Dump Slope
Determining the shear strength parameters of granular materials in high waste rock dump slopes is essential for reliable slope stability analysis. In this study, dump materials were sampled from six benches (elevations 2800–2950 m) of an open-pit mine dump slope, and in situ density tests, gradation analyses, and large-scale consolidated drained (CD) triaxial tests were performed. Two PFC2D slope models—one with uniform (spatially averaged) parameters and one with elevation-dependent (layered) parameters—were then established to quantify how spatial heterogeneity affects stability predictions. The results show pronounced vertical heterogeneity: density, porosity, gradation, and shear strength parameters vary systematically among benches, reflecting the combined effects of compaction history and particle segregation during dumping. All specimens exhibited strain hardening and continuous shear contraction, and specimens with a denser, better-graded structure showed higher strength and lower compressibility. The layered model yields a higher factor of safety and shallower, bench-scale slip surfaces, whereas the uniform model underestimates stability and misplaces the critical slip zones. These findings demonstrate that elevation-dependent parameter assignment better represents the heterogeneous failure mechanism of high dump slopes and should be preferred over uniform parameterization in stability analyses of similar waste rock dumps.
- 13 August 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (8) , 330
Open AccessExperimental Investigation and Numerical Simulation on the Strength and Deformation Characteristics of Granular Materials at Various Elevations of Dump Slope
Determining the shear strength parameters of granular materials in high waste rock dump slopes is essential for reliable slope stability analysis. In this study, dump materials were sampled from six benches (elevations 2800–2950 m) of an open-pit mine dump slope, and in situ density tests, gradation analyses, and large-scale consolidated drained (CD) triaxial tests were performed. Two PFC2D slope models—one with uniform (spatially averaged) parameters and one with elevation-dependent (layered) parameters—were then established to quantify how spatial heterogeneity affects stability predictions. The results show pronounced vertical heterogeneity: density, porosity, gradation, and shear strength parameters vary systematically among benches, reflecting the combined effects of compaction history and particle segregation during dumping. All specimens exhibited strain hardening and continuous shear contraction, and specimens with a denser, better-graded structure showed higher strength and lower compressibility. The layered model yields a higher factor of safety and shallower, bench-scale slip surfaces, whereas the uniform model underestimates stability and misplaces the critical slip zones. These findings demonstrate that elevation-dependent parameter assignment better represents the heterogeneous failure mechanism of high dump slopes and should be preferred over uniform parameterization in stability analyses of similar waste rock dumps.
- Open Access
Modification of Rock Stress Factor for the Mathews Stability Graph Method Based on Hoek–Brown Criterion and Its Application
During underground mining, stope stability is affected by excavation-induced stress redistribution and nonlinear degradation of rock mass strength. The conventional Mathews stability graph method employs an empirical stress factor A, which does not explicitly consider the nonlinear relationship between stress conditions and rock mass strength. In this study, the generalized Hoek–Brown criterion was introduced to define the maximum stress factor (MSF), and a modified stress factor A′ was developed by considering tensile and shear failure mechanisms. The proposed method incorporates the nonlinear stress–stability relationship of underground stopes and improves the reliability of stability assessment. A copper mine in southwest China was selected as a case study. The rock mass quality indices and stress parameters of ten representative stopes were obtained through field investigations, stope roof stress measurements, discontinuity surveys, and laboratory tests. The modified stress factor A′ was incorporated into the Mathews stability graph to account for excavation-induced stress redistribution and rock mass strength degradation. Compared with the conventional method, the modified approach generally reduced the stability numbers of the investigated stopes, with an average reduction of approximately 25.6% (excluding D1780-1, where the confinement strengthening effect resulted in a slight increase in stability number). The revised stability classifications show good consistency with the FLAC3D simulation results and field observations, providing supporting evidence for the application of the proposed method to underground stope stability assessment in the studied mine.
Open AccessModification of Rock Stress Factor for the Mathews Stability Graph Method Based on Hoek–Brown Criterion and Its Application
During underground mining, stope stability is affected by excavation-induced stress redistribution and nonlinear degradation of rock mass strength. The conventional Mathews stability graph method employs an empirical stress factor A, which does not explicitly consider the nonlinear relationship between stress conditions and rock mass strength. In this study, the generalized Hoek–Brown criterion was introduced to define the maximum stress factor (MSF), and a modified stress factor A′ was developed by considering tensile and shear failure mechanisms. The proposed method incorporates the nonlinear stress–stability relationship of underground stopes and improves the reliability of stability assessment. A copper mine in southwest China was selected as a case study. The rock mass quality indices and stress parameters of ten representative stopes were obtained through field investigations, stope roof stress measurements, discontinuity surveys, and laboratory tests. The modified stress factor A′ was incorporated into the Mathews stability graph to account for excavation-induced stress redistribution and rock mass strength degradation. Compared with the conventional method, the modified approach generally reduced the stability numbers of the investigated stopes, with an average reduction of approximately 25.6% (excluding D1780-1, where the confinement strengthening effect resulted in a slight increase in stability number). The revised stability classifications show good consistency with the FLAC3D simulation results and field observations, providing supporting evidence for the application of the proposed method to underground stope stability assessment in the studied mine.
- Open Access
- 2 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (7) , 3445
Calculation Method of Foundation Bearing Capacity of Waste Dumps Based on Boussinesq Equation
The insufficient bearing capacity of the foundation at waste dumps can easily lead to landslides and other geohazards. At present, discrepancies between the calculated bearing capacity of such foundations and actual field performance are a major cause of these accidents. Therefore, further research into methods for accurately estimating the foundation bearing capacity of waste dumps to guide engineering practice is crucial for preventing such incidents. This study employs a combination of theoretical and case analysis to examine the current calculation methods. We discover that the calculated values are smaller than the actual values. Moreover, by taking into account both the upper load of the waste dumps and the bearing capacity of the lower foundation, we analyzed the main problems leading to the underestimation. In response to the aforementioned issues, this study suggests incorporating the Boussinesq equation into the calculation of the upper load to account for the load distribution across various slope forms and the diffusion and superposition of stress at different foundation positions and depths. Simultaneously, the foundation’s bearing capacity is calculated to increase with burial depth, aligning with the stress at different positions. Finally, a new method for calculating the bearing capacity of foundations at waste dumps was developed. The bearing capacities of the waste dump foundation and the weakest point determined using the proposed method are validated through a case study and FLAC3D numerical simulation. This study can provide a reference for calculating the bearing capacity of foundations in similar waste dumps.
- 2 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (7) , 3445
Open AccessCalculation Method of Foundation Bearing Capacity of Waste Dumps Based on Boussinesq Equation
The insufficient bearing capacity of the foundation at waste dumps can easily lead to landslides and other geohazards. At present, discrepancies between the calculated bearing capacity of such foundations and actual field performance are a major cause of these accidents. Therefore, further research into methods for accurately estimating the foundation bearing capacity of waste dumps to guide engineering practice is crucial for preventing such incidents. This study employs a combination of theoretical and case analysis to examine the current calculation methods. We discover that the calculated values are smaller than the actual values. Moreover, by taking into account both the upper load of the waste dumps and the bearing capacity of the lower foundation, we analyzed the main problems leading to the underestimation. In response to the aforementioned issues, this study suggests incorporating the Boussinesq equation into the calculation of the upper load to account for the load distribution across various slope forms and the diffusion and superposition of stress at different foundation positions and depths. Simultaneously, the foundation’s bearing capacity is calculated to increase with burial depth, aligning with the stress at different positions. Finally, a new method for calculating the bearing capacity of foundations at waste dumps was developed. The bearing capacities of the waste dump foundation and the weakest point determined using the proposed method are validated through a case study and FLAC3D numerical simulation. This study can provide a reference for calculating the bearing capacity of foundations in similar waste dumps.