Ahmet Çetin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ahmet Çetin has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Ali Ozer
Department of Materials Science and Engineering University of Illinois at Urbana‐Champaign Urbana Illinois USA
2 shared publications - Ebru Şenadım Tüzemen
Sivas Cumhuriyet Üniversitesi
2 shared publications - Mehmet Şimşir
Sivas Cumhuriyet Üniversitesi
2 shared publications
Latest Publications
- 29 June 2026
- Published by Cumhuriyet University in Cumhuriyet Science Journal
- Vol. 47 (3) , 557-565
Structural, Morphological, and Photocatalytic Comparison of TiO₂ Thin Films Deposited by RF Magnetron Sputtering at Room Temperature and 300 °C
In this study, titanium dioxide TiO₂ thin films were deposited onto glass substrates at room temperature and at a substrate temperature of 300°C using the RF magnetron sputtering technique, and their structural, morphological, chemical, and photocatalytic properties were comparatively investigated. XRD analysis revealed that the film deposited at room temperature exhibited a fully amorphous structure, whereas the film deposited at 300°C displayed low-intensity reflections of the anatase (101) and (004) planes on an amorphous background, indicating the onset of limited crystalline nucleation with increasing temperature. Cross-sectional SEM images confirmed the formation of a homogeneous layer with an approximate thickness of 330 nm, while surface SEM micrographs showed a compact and fine-grained morphology characteristic of films deposited at low temperatures. AFM measurements demonstrated a granular surface topography with an RMS roughness of approximately 26 nm over a 10 × 10 µm scan area. FTIR spectra revealed the characteristic Ti–O–Ti vibrational modes, confirming the formation of the TiO₂ network structure. Photocatalytic experiments showed that the TiO₂ film deposited at 300°C achieved approximately 74% degradation of methylene blue under UVA irradiation after about 9 hours, exhibiting significantly higher photocatalytic activity compared to the room-temperature film. This improvement is attributed to partial structural ordering and increased surface roughness. Overall, the findings demonstrate that the structural evolution occurring in TiO₂ thin films deposited at low temperatures directly influences their photocatalytic behavior, and that TiO₂ films exhibiting considerable photocatalytic performance can be produced even at moderate deposition temperatures such as 300°C.
- 29 June 2026
- Published by Cumhuriyet University in Cumhuriyet Science Journal
- Vol. 47 (3) , 557-565
Structural, Morphological, and Photocatalytic Comparison of TiO₂ Thin Films Deposited by RF Magnetron Sputtering at Room Temperature and 300 °C
In this study, titanium dioxide TiO₂ thin films were deposited onto glass substrates at room temperature and at a substrate temperature of 300°C using the RF magnetron sputtering technique, and their structural, morphological, chemical, and photocatalytic properties were comparatively investigated. XRD analysis revealed that the film deposited at room temperature exhibited a fully amorphous structure, whereas the film deposited at 300°C displayed low-intensity reflections of the anatase (101) and (004) planes on an amorphous background, indicating the onset of limited crystalline nucleation with increasing temperature. Cross-sectional SEM images confirmed the formation of a homogeneous layer with an approximate thickness of 330 nm, while surface SEM micrographs showed a compact and fine-grained morphology characteristic of films deposited at low temperatures. AFM measurements demonstrated a granular surface topography with an RMS roughness of approximately 26 nm over a 10 × 10 µm scan area. FTIR spectra revealed the characteristic Ti–O–Ti vibrational modes, confirming the formation of the TiO₂ network structure. Photocatalytic experiments showed that the TiO₂ film deposited at 300°C achieved approximately 74% degradation of methylene blue under UVA irradiation after about 9 hours, exhibiting significantly higher photocatalytic activity compared to the room-temperature film. This improvement is attributed to partial structural ordering and increased surface roughness. Overall, the findings demonstrate that the structural evolution occurring in TiO₂ thin films deposited at low temperatures directly influences their photocatalytic behavior, and that TiO₂ films exhibiting considerable photocatalytic performance can be produced even at moderate deposition temperatures such as 300°C.
- 27 February 2026
- Published by Cumhuriyet University in Cumhuriyet Science Journal
- Vol. 47 (1) , 119-127
Investigation of Structural and Photocatalytic Properties of ZnO Thin Films
This study focuses on the fabrication of immobilized and stable pure ZnO thin films via RF magnetron sputtering to eliminate the drawbacks of powder-based photocatalysts, such as catalyst recovery, filtration difficulties, and secondary pollution risks. While the photocatalytic potential of ZnO is well established, research investigating the structural origins of performance enhancement in undoped ZnO thin films achieved through physical vapor deposition (PVD) parameters and post-deposition annealing remains limited. In this context, the contribution of this work lies in the quantitative demonstration of the enhancement in photocatalytic performance induced by annealing at 400 °C in additive-free ZnO thin films. As-deposited and 400 °C annealed ZnO thin films were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and energy-dispersive X-ray spectroscopy (EDX). XRD analysis confirmed a hexagonal wurtzite structure for both films, while post-deposition annealing improved crystalline quality and increased the average crystallite size from 53.3 nm to 57.2 nm. AFM measurements revealed an increase in surface roughness from 1.252 nm to 12.14 nm after annealing. Photocatalytic degradation experiments of methylene blue (MB) were conducted under UV-A irradiation, and concentration changes were monitored by UV–Vis spectroscopy. The as-deposited ZnO thin films exhibited only 11% degradation efficiency after 8 hours, whereas the films annealed at 400 °C achieved 68% degradation after 11 hours, corresponding to a sevenfold enhancement in photocatalytic performance. These results demonstrate that post-deposition annealing is an effective strategy for optimizing the photocatalytic activity of pure ZnO thin films under low-energy UV-A light.
- 27 February 2026
- Published by Cumhuriyet University in Cumhuriyet Science Journal
- Vol. 47 (1) , 119-127
Investigation of Structural and Photocatalytic Properties of ZnO Thin Films
This study focuses on the fabrication of immobilized and stable pure ZnO thin films via RF magnetron sputtering to eliminate the drawbacks of powder-based photocatalysts, such as catalyst recovery, filtration difficulties, and secondary pollution risks. While the photocatalytic potential of ZnO is well established, research investigating the structural origins of performance enhancement in undoped ZnO thin films achieved through physical vapor deposition (PVD) parameters and post-deposition annealing remains limited. In this context, the contribution of this work lies in the quantitative demonstration of the enhancement in photocatalytic performance induced by annealing at 400 °C in additive-free ZnO thin films. As-deposited and 400 °C annealed ZnO thin films were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and energy-dispersive X-ray spectroscopy (EDX). XRD analysis confirmed a hexagonal wurtzite structure for both films, while post-deposition annealing improved crystalline quality and increased the average crystallite size from 53.3 nm to 57.2 nm. AFM measurements revealed an increase in surface roughness from 1.252 nm to 12.14 nm after annealing. Photocatalytic degradation experiments of methylene blue (MB) were conducted under UV-A irradiation, and concentration changes were monitored by UV–Vis spectroscopy. The as-deposited ZnO thin films exhibited only 11% degradation efficiency after 8 hours, whereas the films annealed at 400 °C achieved 68% degradation after 11 hours, corresponding to a sevenfold enhancement in photocatalytic performance. These results demonstrate that post-deposition annealing is an effective strategy for optimizing the photocatalytic activity of pure ZnO thin films under low-energy UV-A light.