JZJingxiong Zhang

Jingxiong Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jingxiong Zhang has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Compressive behavior and energy absorption of SLM-fabricated diamond-TPMS tube reinforced with bionic spider-web ribs

    by Jingxiong Zhang, Guangsheng Liu, Chao Xiong, Kaibo Cui, Junhui Yin, Xiujie Zhu, Jialong Liu

    Aluminum alloy thin-walled tubes are widely used in lightweight energy-absorbing structures owing to their high specific strength and crashworthiness. However, Diamond-type triply periodic minimal surface (TPMS) tubes may exhibit unstable penetrating 45° shear band deformation under axial compression. To mitigate this instability, a bionic spider-web rib-reinforced Diamond-TPMS tube (D-BCT) is proposed based on spatial–structural partitioning, dividing the annular region into an inner rib-reinforced region and an outer Diamond-TPMS region. Three specimens of each structure were fabricated from AlSi10Mg alloy by selective laser melting and tested under quasi-static axial compression. Within a common 0–15 mm evaluation displacement, the D-BCT achieved a mean specific energy absorption (SEA) of 38.74 J/g, approximately 9.9% higher than that of the conventional Diamond-TPMS tube (D-CT), while reducing the mean peak crushing force by approximately 30.7% and increasing the mean crushing force efficiency (CFE) from 64.66% to 74.92%. Compared with D-CT, D-BCT exhibited progressive crushing and buckling rather than a penetrating shear band, together with a more stable plateau response. These results suggest that spatial–structural partitioning is a promising approach for improving the quasi-static crushing stability of Diamond-TPMS tubes.

  • Open Access

    Compressive behavior and energy absorption of SLM-fabricated Diamond-TPMS tube reinforced with bionic spider-web ribs

    by Jingxiong Zhang, Guangsheng Liu, Chao Xiong, Kaibo Cui, Junhui Yin, Xiujie Zhu, Jialong Liu

    Aluminum alloys are widely used in automotive, aerospace, and defense, due to their high specific strength and high energy absorption. However, thin-walled aluminum alloy tubes with Diamond-type triply periodic minimal surface (TPMS) lattices often create 45°penetrating shear bands under axial compression. To address this, we propose a Diamond-TPMS tube reinforced with bionic spider-web ribs (D-BCT), inspired by the radial-circumferential topology of natural spider webs. This structure was fabricated via selective laser melting (SLM). We performed quasi-static compression tests and macroscopic failure analysis to evaluate and compare the mechanical responses and deformation modes of three configurations: a empty thin-walled tube (CT), a Diamond-TPMS-filled tube (D-CT), and the D-BCT hybrid structure. The results show that the bionic spider-web ribs in the D-BCT significantly mitigate through-thickness shear failure in the Diamond TPMS lattices, transitioning the failure mode from catastrophic shear failure to stable, progressive crushing. Over an effective compression stroke of 0–20 mm, the D-BCT achieved a specific energy absorption of 48.22 J/g, which is 95.02% higher than that of the CT. Compared to D-CT, the D-BCT reduced the initial peak force by 30.88%, increased the crushing force efficiency to 69.32%, and markedly reduced load fluctuations in the plateau region. This study confirms that the synergistic design of bionic topology and TPMS lattices enables high specific energy absorption with low peak force and enhanced energy dissipation stability. These findings provide a promising strategy for the design of lightweight, energy-absorbing structures, especially in the context of metal additive manufacturing.