Sein Min
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sein Min has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Hee Chang Jeon
Department of Mechanical, Robotics and Energy Engineering, Dongguk University, Jung-gu, Seoul 04620, Republic of Korea
2 shared publications - Jiseon Yun
Department of Mechanical, Robotics and Energy Engineering, Dongguk University, Jung-gu, Seoul 04620, Republic of Korea
2 shared publications - Joong Yeon Lim
Department of Mechanical, Robotics and Energy Engineering, Dongguk University, Jung-gu, Seoul 04620, Republic of Korea
2 shared publications - Woohyuk Jang
Department of Mechanical, Robotics and Energy Engineering, Dongguk University, Jung-gu, Seoul 04620, Republic of Korea
2 shared publications - Young-Seong Kim
Department of Mechanical, Robotics and Energy Engineering, Dongguk University, Jung-gu, Seoul 04620, Republic of Korea
2 shared publications
Latest Publications
- Open Access
Fabrication of Electrospun PAN–CNT–CNC Composite Nanofiber Films for Hydrovoltaic Energy Harvesting
Water-induced electrical responses were investigated using porous electrospun PAN-based composite membranes containing CNTs and CNCs. Following the injection of 20 μL of a 2 wt% NaCl solution, transient open-circuit voltage responses were observed from the PAN, PAN–CNT, and PAN–CNT–CNC devices, with maximum values of approximately 47, 42, and 68 mV, respectively, in the tested devices. Three successive injection–drying cycles demonstrated repeated transient responses within individual devices but did not establish device-to-device reproducibility or long-term stability. Raman and FTIR analyses supported the incorporation of CNTs and the modification of the water-interacting environment following CNC addition, respectively. The voltage waveform depended on the liquid type, NaCl concentration, and wetting–drying history, including a transient reverse-voltage response during drying. These results provide a proof-of-concept observation of wetting–drying-dependent electrical behavior in electrospun PAN-based porous membranes. Load-dependent power, long-term durability, and device-to-device reproducibility remain to be established.
Open AccessFabrication of Electrospun PAN–CNT–CNC Composite Nanofiber Films for Hydrovoltaic Energy Harvesting
Water-induced electrical responses were investigated using porous electrospun PAN-based composite membranes containing CNTs and CNCs. Following the injection of 20 μL of a 2 wt% NaCl solution, transient open-circuit voltage responses were observed from the PAN, PAN–CNT, and PAN–CNT–CNC devices, with maximum values of approximately 47, 42, and 68 mV, respectively, in the tested devices. Three successive injection–drying cycles demonstrated repeated transient responses within individual devices but did not establish device-to-device reproducibility or long-term stability. Raman and FTIR analyses supported the incorporation of CNTs and the modification of the water-interacting environment following CNC addition, respectively. The voltage waveform depended on the liquid type, NaCl concentration, and wetting–drying history, including a transient reverse-voltage response during drying. These results provide a proof-of-concept observation of wetting–drying-dependent electrical behavior in electrospun PAN-based porous membranes. Load-dependent power, long-term durability, and device-to-device reproducibility remain to be established.
- Open Access
- 30 August 2026
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 27 (17) , 7770
Nanoscale Electromechanical and Conductive Properties of a Layered Two-Dimensional Hybrid Perovskite
Two-dimensional (2D) organic–inorganic hybrid perovskites exhibit coupled ionic, electronic, and electromechanical responses that can strongly influence local charge transport. Here, solution-processed mixed-halide butylammonium lead perovskite crystals were mechanically exfoliated and investigated using X-ray diffraction, atomic force microscopy, piezoresponse force microscopy (PFM), and conductive atomic force microscopy (c-AFM). PFM measurements under −5, 0, and +5 V revealed clear bias-dependent changes in amplitude and phase, indicating an electric field-sensitive local electromechanical response. Local c-AFM measurements showed nonlinear bipolar hysteresis, with a pronounced increase in current near +7–8 V and a decrease near −7 to −6 V during the subsequent negative sweep. Because the crystals are mixed ionic–electronic conductors and the nanoscale tip–sample junction introduces substantial injection and contact barriers, the observed behavior is interpreted as resistive switching-like conductivity modulation, rather than definitive ferroelectric switching. The results are consistent with the combined contributions of charge injection, trap filling, possible ionic redistribution, and piezoelectricity-associated modulation of the local transport barrier. These findings provide nanoscale insight into electric field-dependent electromechanical and out-of-plane conductive behaviors in layered 2D hybrid perovskites.
- 30 August 2026
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 27 (17) , 7770
Open AccessNanoscale Electromechanical and Conductive Properties of a Layered Two-Dimensional Hybrid Perovskite
Two-dimensional (2D) organic–inorganic hybrid perovskites exhibit coupled ionic, electronic, and electromechanical responses that can strongly influence local charge transport. Here, solution-processed mixed-halide butylammonium lead perovskite crystals were mechanically exfoliated and investigated using X-ray diffraction, atomic force microscopy, piezoresponse force microscopy (PFM), and conductive atomic force microscopy (c-AFM). PFM measurements under −5, 0, and +5 V revealed clear bias-dependent changes in amplitude and phase, indicating an electric field-sensitive local electromechanical response. Local c-AFM measurements showed nonlinear bipolar hysteresis, with a pronounced increase in current near +7–8 V and a decrease near −7 to −6 V during the subsequent negative sweep. Because the crystals are mixed ionic–electronic conductors and the nanoscale tip–sample junction introduces substantial injection and contact barriers, the observed behavior is interpreted as resistive switching-like conductivity modulation, rather than definitive ferroelectric switching. The results are consistent with the combined contributions of charge injection, trap filling, possible ionic redistribution, and piezoelectricity-associated modulation of the local transport barrier. These findings provide nanoscale insight into electric field-dependent electromechanical and out-of-plane conductive behaviors in layered 2D hybrid perovskites.