Zhiwei Qin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhiwei Qin has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Bingzhi Wang
School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024, PR China
2 shared publicationsFushuai Jin
School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024, PR China
2 shared publications- Honggang Dong
School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024, PR China
2 shared publications Bin Wang
1 shared publicationChi Pan
1 shared publicationChunbo Zhang
Heilongjiang Provincial Key Laboratory of Advanced Friction Welding Technology and Equipment, Harbin 150028, PR China
1 shared publication
Latest Publications
- 2 November 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (21) , 10683-10696
An interfacial nanostructure-specific tailoring strategy to address the strength and ductility trade-off in inertia friction welded dissimilar superalloys
Inertia friction welding (IFW) of dissimilar Ni-based superalloys offers great promise for aero-engine manufacturing, yet the persistent strength–ductility trade-off in welded joints restricts their reliable service under extreme conditions.
- 2 November 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (21) , 10683-10696
An interfacial nanostructure-specific tailoring strategy to address the strength and ductility trade-off in inertia friction welded dissimilar superalloys
Inertia friction welding (IFW) of dissimilar Ni-based superalloys offers great promise for aero-engine manufacturing, yet the persistent strength–ductility trade-off in welded joints restricts their reliable service under extreme conditions.
- Open Access
- 21 October 2026
- Published by Elsevier in SSRN Electronic Journal
Non-monotonic strength in WAAM Al-Zn-Mg-Cu alloy under transient thermal cycling: Microstructural origins and role of arc energy
Wire arc additive manufacturing (WAAM) of high-strength Al-Zn-Mg-Cu alloys involves complex transient thermal cycles that alter the balance among strengthening mechanisms, thereby affecting mechanical properties. Herein, Al-Zn-Mg-Cu thin walls were fabricated at arc energies of 76.8, 89.6, and 107.5 J mm-1 to investigate how thermal input influences the competition among strengthening mechanisms. The deposits consisted of an α-Al matrix with η phase precipitates. The tensile response was non-monotonic: the wall fabricated at 89.6 J mm-1 exhibited the highest yield strength in both the horizontal and vertical directions despite having the largest average grain size (131.3 μm). The corresponding ultimate tensile strengths and elongations in the horizontal and vertical directions were 251 and 208 MPa and 3.6% and 2.0%, respectively. With increasing arc energy, cellular/dendritic structures and η phase precipitates coarsened, while the local solute concentration in the α-Al matrix decreased. The wall fabricated at 89.6 J mm-1 exhibited the highest KAM and contained dispersed intragranular equilibrium η precipitates. An incoherent η/α-Al interface and a coherent η/η boundary inside the grain-boundary η precipitate were also identified in this wall. These observations suggest that enhanced dislocation strengthening and particle strengthening likely compensate for the reduced grain-boundary and solid-solution strengthening contributions. Among the investigated conditions, 89.6 J mm-1 provided a favorable combination of strength and ductility.
- 21 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessNon-monotonic strength in WAAM Al-Zn-Mg-Cu alloy under transient thermal cycling: Microstructural origins and role of arc energy
Wire arc additive manufacturing (WAAM) of high-strength Al-Zn-Mg-Cu alloys involves complex transient thermal cycles that alter the balance among strengthening mechanisms, thereby affecting mechanical properties. Herein, Al-Zn-Mg-Cu thin walls were fabricated at arc energies of 76.8, 89.6, and 107.5 J mm-1 to investigate how thermal input influences the competition among strengthening mechanisms. The deposits consisted of an α-Al matrix with η phase precipitates. The tensile response was non-monotonic: the wall fabricated at 89.6 J mm-1 exhibited the highest yield strength in both the horizontal and vertical directions despite having the largest average grain size (131.3 μm). The corresponding ultimate tensile strengths and elongations in the horizontal and vertical directions were 251 and 208 MPa and 3.6% and 2.0%, respectively. With increasing arc energy, cellular/dendritic structures and η phase precipitates coarsened, while the local solute concentration in the α-Al matrix decreased. The wall fabricated at 89.6 J mm-1 exhibited the highest KAM and contained dispersed intragranular equilibrium η precipitates. An incoherent η/α-Al interface and a coherent η/η boundary inside the grain-boundary η precipitate were also identified in this wall. These observations suggest that enhanced dislocation strengthening and particle strengthening likely compensate for the reduced grain-boundary and solid-solution strengthening contributions. Among the investigated conditions, 89.6 J mm-1 provided a favorable combination of strength and ductility.
- 12 September 2026
- Published by Elsevier in Electrochimica Acta
- Vol. 579
Achieving synergistic enhancement of strength and corrosion resistance in Al/steel FSWed joints by a Sn interlayer
- 12 September 2026
- Published by Elsevier in Electrochimica Acta
- Vol. 579
Achieving synergistic enhancement of strength and corrosion resistance in Al/steel FSWed joints by a Sn interlayer