Risa Shoji
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Risa Shoji has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Akihiko Hanafusa
Shibaura Institute of Technology, Saitama, Japan
1 shared publication - Eiji Iwasaki
Department of Orthopaedic Surgery, Juntendo University, Tokyo, Japan
1 shared publication - Ken Tashiro
Department of Medicine for Orthopaedics and Motor Organ, Juntendo University Graduate School of Medicine, Tokyo, Japan
1 shared publication - Koju Hayashi
Department of Orthopaedic Surgery, Juntendo University, Tokyo, Japan
1 shared publication - Muneaki Ishijima
Department of Orthopaedics, Juntendo University Faculty of Medicine, Tokyo, Japan
1 shared publication - Taiji Watari
Department of Orthopaedic Surgery, Juntendo University, Tokyo, Japan
1 shared publication
Latest Publications
- 21 September 2026
- Published by Springer Nature in International Orthopaedics
- Vol. 50 (12) , 3171-3179
Intraoperative six-axis loads during direct anterior approach total hip arthroplasty using a leg positioner: quantitative patterns across manoeuvres
Purpose The direct anterior approach (DAA) for total hip arthroplasty (THA) commonly uses leg positioners to facilitate femoral exposure, but intraoperative lower-limb loading during these manoeuvres remains poorly understood. This study quantitatively assessed six-axis loads during femoral preparation in leg positioner-assisted DAA-THA. Methods This prospective observational biomechanical study included 95 hips undergoing primary DAA-THA using a leg positioner. A six-axis force sensor mounted on the operative boot recorded forces (Fx, Fy, Fz) and moments (Mx, My, Mz) at baseline and at two predefined static endpoint measurement points: the extension endpoint and the final stem position after adduction. Values were expressed relative to baseline and represented static endpoint measurements rather than peak values during dynamic manoeuvres. Measurements were standardised to a right-sided coordinate system. Repeated-measures analysis of variance with Bonferroni-corrected post hoc paired comparisons was used. Results At the extension endpoint, distal traction force was greatest (Fz; 170.6 ± 51.9 N). At the final stem position after adduction, distal traction force decreased compared with the extension endpoint but remained elevated relative to baseline (126.9 ± 45.7 N), and Mx showed the greatest magnitude among the moment components. The maximum endpoint Fz relative to baseline was recorded at the extension endpoint (322.8 N). No significant associations were found between final-position Fz and age, sex, height, weight, body mass index, or diagnosis. Mean stem rasping time was 10 min 48 s ± 4 min 28 s (648 ± 268 s). Conclusion During leg positioner-assisted DAA-THA, the extension endpoint generated the highest distal traction force, whereas the final stem position after adduction was associated with residual distal traction force and a greater magnitude of Mx.
- 21 September 2026
- Published by Springer Nature in International Orthopaedics
- Vol. 50 (12) , 3171-3179
Intraoperative six-axis loads during direct anterior approach total hip arthroplasty using a leg positioner: quantitative patterns across manoeuvres
Purpose The direct anterior approach (DAA) for total hip arthroplasty (THA) commonly uses leg positioners to facilitate femoral exposure, but intraoperative lower-limb loading during these manoeuvres remains poorly understood. This study quantitatively assessed six-axis loads during femoral preparation in leg positioner-assisted DAA-THA. Methods This prospective observational biomechanical study included 95 hips undergoing primary DAA-THA using a leg positioner. A six-axis force sensor mounted on the operative boot recorded forces (Fx, Fy, Fz) and moments (Mx, My, Mz) at baseline and at two predefined static endpoint measurement points: the extension endpoint and the final stem position after adduction. Values were expressed relative to baseline and represented static endpoint measurements rather than peak values during dynamic manoeuvres. Measurements were standardised to a right-sided coordinate system. Repeated-measures analysis of variance with Bonferroni-corrected post hoc paired comparisons was used. Results At the extension endpoint, distal traction force was greatest (Fz; 170.6 ± 51.9 N). At the final stem position after adduction, distal traction force decreased compared with the extension endpoint but remained elevated relative to baseline (126.9 ± 45.7 N), and Mx showed the greatest magnitude among the moment components. The maximum endpoint Fz relative to baseline was recorded at the extension endpoint (322.8 N). No significant associations were found between final-position Fz and age, sex, height, weight, body mass index, or diagnosis. Mean stem rasping time was 10 min 48 s ± 4 min 28 s (648 ± 268 s). Conclusion During leg positioner-assisted DAA-THA, the extension endpoint generated the highest distal traction force, whereas the final stem position after adduction was associated with residual distal traction force and a greater magnitude of Mx.