Luis Criollo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Luis Criollo has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Dayana Llumiquinga
Departamento de Ciencias de la Energía y Mecánica, Universidad de las Fuerzas Armadas ESPE, Sangolquí 171103, Ecuador
1 shared publication - Germán Omar Barrionuevo
Department of Mechanical Engineering, Universidad San Francisco de Quito USFQ, Diego de Robles y Vía Interoceánica, Quito P.O. Box 17-0901, Ecuador
1 shared publication - Jhon Luna-Jaén
Departamento de Ciencias de la Energía y Mecánica, Universidad de las Fuerzas Armadas ESPE, Sangolquí 171103, Ecuador
1 shared publication - Santiago Daniel Puma-Araujo
School of Engineering and Sciences, Tecnologico de Monterrey, Monterrey 64849, Mexico
1 shared publication - Wilson Navas-Pinto
Departamento de Ciencias de la Energía y Mecánica, Universidad de las Fuerzas Armadas ESPE, Sangolquí 171103, Ecuador
1 shared publication - Xavier Sánchez-Sánchez
Departamento de Ciencias de la Energía y Mecánica, Universidad de las Fuerzas Armadas ESPE, Sangolquí 171103, Ecuador
1 shared publication
Latest Publications
- Open Access
Influence of Low TiO2 Nanoparticle Loading on Electrospun sPEEK Fiber Morphology and Chemistry and on the Tensile Properties of Corresponding Solution-Cast Membranes
Polymer matrix composites (PMCs) have garnered importance due to their unique combination of mechanical, thermal, and functional properties. However, their performance depends on overcoming challenges related to dispersion, bonding, and processing. Electrospinning is an advanced technique for producing nanofiber or microfiber PMCs. One of the key challenges in electrospun PMCs is the uniform dispersion of reinforcement materials like nanoparticles within the polymer matrix. A Taguchi orthogonal design () was used to evaluate the effects of needle-to-collector distance, applied voltage, and flow rate on mean fiber diameter and deposition quality. Scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR) were used to characterize electrospun neat sulfonated poly(ether ether ketone) (sPEEK) and sPEEK/TiO2 fibers, whereas tensile tests were performed on solution-cast membranes prepared from the corresponding formulations. The lowest observed run mean diameter was 204.6695 nm at 8 kV, 1.25 mL h−1, and a needle-to-collector distance of 12 cm; this run was also selected for deposition quality. Neat sPEEK membranes exhibited a mean tensile strength of 35.3 MPa, a mean apparent tensile modulus of 476 MPa, and a mean elongation at fracture of 18%. Among the TiO2-containing formulations, increasing the TiO2 content from 0.04 to 0.10 wt.% was associated with higher mean apparent tensile modulus and tensile strength and lower mean elongation at fracture. The 0.10 wt.% formulation exhibited the highest mean apparent tensile modulus and tensile strength.Open AccessInfluence of Low TiO2 Nanoparticle Loading on Electrospun sPEEK Fiber Morphology and Chemistry and on the Tensile Properties of Corresponding Solution-Cast Membranes
Polymer matrix composites (PMCs) have garnered importance due to their unique combination of mechanical, thermal, and functional properties. However, their performance depends on overcoming challenges related to dispersion, bonding, and processing. Electrospinning is an advanced technique for producing nanofiber or microfiber PMCs. One of the key challenges in electrospun PMCs is the uniform dispersion of reinforcement materials like nanoparticles within the polymer matrix. A Taguchi orthogonal design () was used to evaluate the effects of needle-to-collector distance, applied voltage, and flow rate on mean fiber diameter and deposition quality. Scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR) were used to characterize electrospun neat sulfonated poly(ether ether ketone) (sPEEK) and sPEEK/TiO2 fibers, whereas tensile tests were performed on solution-cast membranes prepared from the corresponding formulations. The lowest observed run mean diameter was 204.6695 nm at 8 kV, 1.25 mL h−1, and a needle-to-collector distance of 12 cm; this run was also selected for deposition quality. Neat sPEEK membranes exhibited a mean tensile strength of 35.3 MPa, a mean apparent tensile modulus of 476 MPa, and a mean elongation at fracture of 18%. Among the TiO2-containing formulations, increasing the TiO2 content from 0.04 to 0.10 wt.% was associated with higher mean apparent tensile modulus and tensile strength and lower mean elongation at fracture. The 0.10 wt.% formulation exhibited the highest mean apparent tensile modulus and tensile strength.