Rishabh Raj
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Rishabh Raj has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Boggavarapu Sai Ram
Department of Electrical, Electronics and Communication Engineering, Indian Institute of Technology Dharwad, Dharwad, India
1 shared publication - Deepak Singh
Department of Electrical Engineering and Automation, Aalto University, Espoo, Finland
1 shared publication - Greeshma Mohan Unniachanparambil
Department of Electrical Engineering, IIT Bombay, Mumbai, India
1 shared publication Kim Bergsro
Electromechanical System Team, Volvo Cars Corporation in Gothenburg, Gteborg, Sweden
1 shared publication- Rahul Bhat
IIT Bombay, Mumbai, India
1 shared publication - Shrikrishna V. Kulkarni
Department of Electrical Engineering, Indian Institute of Technology Bombay, Mumbai, India
1 shared publication
Latest Publications
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 40 (4) , 2736-2746
Characterizing the Effect of Shrink Fitting of Stator Housings on Electric Vehicle Performance
High performance rotating electric machines are a necessity in the automotive sector. The characteristics of electric steel materials given in the datasheet used in electric machines do not account for the effect of stress due to the manufacturing process. It is possible to account for the effect of stress coming more precisely from stator housings after press and shrink fitting which degrades the loss properties of electrical steel. A process is developed, which includes the development of a test bench for characterizing the magnetic properties of electric steel when put under compressive stress. The proposed hardware setup is a novel test bench capable of achieving high compressive stress up to 60 MPa and for a maximum of 1 kHz fundamental frequency. A modified compressive stress dependent loss model for analyzing impact on the total power loss is proposed. Further, a coupled multiphysics finite element analysis including structural and magnetic analysis to evaluate the machine performance over the entire operating range and vehicle performance over relevant drive cycles for passenger electric vehicles. A 7% increase in total machine losses was found at an average in a WLTC class-3 drive cycle due to shrink and press fitting of the stator housing.
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 40 (4) , 2736-2746
Characterizing the Effect of Shrink Fitting of Stator Housings on Electric Vehicle Performance
High performance rotating electric machines are a necessity in the automotive sector. The characteristics of electric steel materials given in the datasheet used in electric machines do not account for the effect of stress due to the manufacturing process. It is possible to account for the effect of stress coming more precisely from stator housings after press and shrink fitting which degrades the loss properties of electrical steel. A process is developed, which includes the development of a test bench for characterizing the magnetic properties of electric steel when put under compressive stress. The proposed hardware setup is a novel test bench capable of achieving high compressive stress up to 60 MPa and for a maximum of 1 kHz fundamental frequency. A modified compressive stress dependent loss model for analyzing impact on the total power loss is proposed. Further, a coupled multiphysics finite element analysis including structural and magnetic analysis to evaluate the machine performance over the entire operating range and vehicle performance over relevant drive cycles for passenger electric vehicles. A 7% increase in total machine losses was found at an average in a WLTC class-3 drive cycle due to shrink and press fitting of the stator housing.
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-8
A Novel Cost-Effective Magnetic Characterization Tool for Soft Magnetic Materials Used in Electrical Machines
Energy losses during the magnetization process of soft magnetic laminations depend on the excitation waveform. Manufacturers of magnetic materials may not provide losses for different excitation waveforms. This may affect the accuracy of the predicted losses which are used to estimate the performance of electrical equipment during the predesign stage. Thus, a characterization tool which is capable of measuring hysteresis loops under controlled magnetization is required. Digital characterization systems available in literature use expensive commercial power amplifiers. In this work, a cost-effective power amplifier circuit is developed and interfaced with a LabVIEW program to characterize soft magnetic materials. The measurements for a sinusoidal excitation from the proposed setup are validated with those from a standard commercial measuring setup. The system is also used to measure hysteresis loops for arbitrary magnetization conditions (magnetic flux density ( B) with harmonics). The proposed setup can operate over a frequency range 35-500 Hz. A small Epstein frame is also designed for measurements at higher frequencies (>200 and <; 500 Hz). A provision is also made to predict three components of dynamic hysteresis losses at any frequency in the above range using the loss separation approach. This capability of the setup enables the user to predict the losses at frequencies beyond the capability of the tool. The predicted losses using this algorithm are validated with measured losses. The proposed setup is cost-effective and can be developed easily using basic electronic components.
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-8
A Novel Cost-Effective Magnetic Characterization Tool for Soft Magnetic Materials Used in Electrical Machines
Energy losses during the magnetization process of soft magnetic laminations depend on the excitation waveform. Manufacturers of magnetic materials may not provide losses for different excitation waveforms. This may affect the accuracy of the predicted losses which are used to estimate the performance of electrical equipment during the predesign stage. Thus, a characterization tool which is capable of measuring hysteresis loops under controlled magnetization is required. Digital characterization systems available in literature use expensive commercial power amplifiers. In this work, a cost-effective power amplifier circuit is developed and interfaced with a LabVIEW program to characterize soft magnetic materials. The measurements for a sinusoidal excitation from the proposed setup are validated with those from a standard commercial measuring setup. The system is also used to measure hysteresis loops for arbitrary magnetization conditions (magnetic flux density ( B) with harmonics). The proposed setup can operate over a frequency range 35-500 Hz. A small Epstein frame is also designed for measurements at higher frequencies (>200 and <; 500 Hz). A provision is also made to predict three components of dynamic hysteresis losses at any frequency in the above range using the loss separation approach. This capability of the setup enables the user to predict the losses at frequencies beyond the capability of the tool. The predicted losses using this algorithm are validated with measured losses. The proposed setup is cost-effective and can be developed easily using basic electronic components.