A Comprehensive and Systematic Analysis of Performance‐Limiting Factors as a Function of IrO 2 Loading Amount in Proton Exchange Membrane Water Electrolysis: IrO 2 Ultra‐Low‐Loading Strategy
Open Access
- 1 January 2026
- journal article
- Published by Wiley in International Journal of Energy Research
- Vol. 2026 (1) , 6003539
Abstract
Proton exchange membrane water electrolysis (PEMWE) enables efficient hydrogen production under high current density operation but requires iridium‐based catalysts to sustain anodic oxygen evolution in acidic environments. Reducing Ir usage without sacrificing cell performance therefore represents a key requirement for practical system implementation. Many studies have shown that increasing Ir loading generally improves electrolyzer performance, but how performance limitations evolve across catalyst loading regimes has not been systematically resolved. In this work, the performance of a PEMWE cell was evaluated over a wide IrO 2 loading range of 0.01–4.0 mg cm −2 . Combined polarization analysis and electrochemical impedance spectroscopy (EIS) were employed to distinguish kinetic, ohmic, and mass‐transport contributions governing cell performance. Increasing catalyst loading substantially improved low‐current‐density operation through mitigation of charge‐transfer limitations, accompanied by a reduction in charge‐transfer resistance ( R ct ) from 5.08 to 0.41 Ω between 0.01 and 0.03 mg cm −2 . At higher loadings, performance improvement became progressively limited and approached current saturation at cell voltages above 1.8 V. The IrO 2 mass activity exhibited a maximum at intermediate loading (0.03 mg cm −2 ) and decreased with further loading increase, indicating incomplete utilization of catalyst layers at large thicknesses. The apparent electrochemically active surface area (ECSA)‐normalized charge‐transfer response remained within the same order of magnitude in the ultra‐low‐loading transition region, indicating that the sharp decrease in R ct primarily reflected an increase in electrochemically connected surface area. At the ultra‐low‐loading end of the range, electrodes prepared at ultra‐low loading showed elevated ohmic resistance associated with insufficient electrical connectivity and reduced interfacial contact with the porous transport layer (PTL). Enhancing PTL–electrode contact significantly improved performance under ultra‐low loading conditions. The results establish loading‐dependent performance regimes governed by distinct limiting processes and provide practical guidance for minimizing iridium usage while maintaining high PEMWE performance.Keywords
Funding Information
- Ministry of Science and ICT, South Korea (RS-2024-00409901)
- Ministry of Science and ICT, South Korea (RS-2024-00431630)
- Korea Institute of Science and Technology (26E0281)
This publication has 45 references indexed in Scilit:
- Photodeposition‐Based Synthesis of TiO2@IrOx Core–Shell Catalyst for Proton Exchange Membrane Water Electrolysis with Low Iridium LoadingAdvanced Science, 2024
- Rhenium Suppresses Iridium (IV) Oxide Crystallization and Enables Efficient, Stable Electrochemical Water OxidationSmall, 2023
- Effect of low voltage limit on degradation mechanism during high‐frequency dynamic load in proton exchange membrane water electrolysisInternational Journal of Energy Research, 2022
- Insights into Interfacial and Bulk Transport Phenomena Affecting Proton Exchange Membrane Water Electrolyzer Performance at Ultra‐Low Iridium LoadingsAdvanced Science, 2021
- Characterization and electrocatalytic properties of electrospun Pt‐IrO2 nanofiber catalysts for oxygen evolution reactionInternational Journal of Energy Research, 2020
- IrO2 coated TiO2 core-shell microparticles advance performance of low loading proton exchange membrane water electrolyzersApplied Catalysis B: Environment and Energy, 2020
- Nano-size IrOx catalyst of high activity and stability in PEM water electrolyzer with ultra-low iridium loadingApplied Catalysis B: Environment and Energy, 2018
- Supported IrxRu1–xO2 Anode Catalysts for PEM‐Water ElectrolysisFuel Cells, 2016
- Influence of iridium oxide loadings on the performance of PEM water electrolysis cells: Part I–Pure IrO 2 -based anodesApplied Catalysis B: Environment and Energy, 2016
- Influence of iridium oxide loadings on the performance of PEM water electrolysis cells: Part II – Advanced oxygen electrodesApplied Catalysis B: Environment and Energy, 2016