Peter Jeschke
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Peter Jeschke has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
- Daniel Weintraub
Institute of Jet Propulsion and Turbomachinery, RWTH Aachen University, Aachen, Germany
5 shared publications - Stefan Henninger
Institute of Jet Propulsion and Turbomachinery, RWTH Aachen University, Aachen, Germany
4 shared publications - Johannes Janssen
Institute of Jet Propulsion and Turbomachinery, RWTH Aachen University, Templergraben 55, 52062 Aachen, Germany
3 shared publications - Magnus Hölle
Institute of Jet Propulsion and Turbomachinery, RWTH Aachen University, Templergraben 55, Aachen 52062, Germany
3 shared publications - Andreas Penkner
Institute of Jet Propulsion and Turbomachinery, RWTH Aachen University, Templergraben 55, Aachen 52062, Germany
2 shared publications - Caitlin Smythe
GE Aviation, Lynn, MA 01910
2 shared publications
Latest Publications
- Open Access
- 5 November 2026
- Published by Springer Nature in CEAS Aeronautical Journal
- p. 1-11
Possibilities and limits of contrail avoidance through aircraft engine design for kerosene- and hydrogen-fuelled engines
In this paper, we present a thermodynamic cycle-based analysis of the effect of aircraft engine design and fuel selection on contrail formation, which is evaluated using the Schmidt–Appleman criterion (SAC). Our goal is to examine the possibilities and limits of contrail avoidance to reduce the climate impact of aviation. We use the gas turbine performance software GasTurb to study geared-turbofan and open-rotor engine designs for contemporary short- to medium-range aircraft. The design parameters are overall pressure ratio, burner exit temperature, and, for the geared-turbofan, the design bypass ratio. We vary these parameters in wide ranges to cover all technically feasible engine designs. We find that contrail formation at current cruise altitudes cannot be avoided with the examined contemporary and future engine cycles. In the best case, the contrail formation altitude is increased by just over 230 m. This comes with a significant engine efficiency penalty. In contrast, future, more efficient engine cycles will decrease the contrail formation altitude, leading to the formation of more contrails. When using hydrogen as fuel instead of kerosene, contrails form at approximately 1.6 km lower altitudes according to the Schmidt–Appleman criterion. We thus find that it is practically impossible to avoid contrail formation, as predicted by the SAC, using the engine cycles and fuels examined in this paper. Operational contrail avoidance measures like cruise altitude adjustment or flying around ice-supersaturated atmospheric layers present themselves as more practicable.
- 5 November 2026
- Published by Springer Nature in CEAS Aeronautical Journal
- p. 1-11
Open AccessPossibilities and limits of contrail avoidance through aircraft engine design for kerosene- and hydrogen-fuelled engines
In this paper, we present a thermodynamic cycle-based analysis of the effect of aircraft engine design and fuel selection on contrail formation, which is evaluated using the Schmidt–Appleman criterion (SAC). Our goal is to examine the possibilities and limits of contrail avoidance to reduce the climate impact of aviation. We use the gas turbine performance software GasTurb to study geared-turbofan and open-rotor engine designs for contemporary short- to medium-range aircraft. The design parameters are overall pressure ratio, burner exit temperature, and, for the geared-turbofan, the design bypass ratio. We vary these parameters in wide ranges to cover all technically feasible engine designs. We find that contrail formation at current cruise altitudes cannot be avoided with the examined contemporary and future engine cycles. In the best case, the contrail formation altitude is increased by just over 230 m. This comes with a significant engine efficiency penalty. In contrast, future, more efficient engine cycles will decrease the contrail formation altitude, leading to the formation of more contrails. When using hydrogen as fuel instead of kerosene, contrails form at approximately 1.6 km lower altitudes according to the Schmidt–Appleman criterion. We thus find that it is practically impossible to avoid contrail formation, as predicted by the SAC, using the engine cycles and fuels examined in this paper. Operational contrail avoidance measures like cruise altitude adjustment or flying around ice-supersaturated atmospheric layers present themselves as more practicable.
- Open Access
- 24 February 2026
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 10, 29-49
Performance calculation of the thermal management system for a fuel cell aircraft engine
This paper presents a novel approach to the design of fuel cell thermal management systems, offering significant advantages for the evaluation of system architectures and design variables. The new performance calculation method considers the flow of cooling air as a separate cycle process. Analytical correlations are employed to describe the cycle process that the cooling air undergoes as it flows through the thermal management system, similar to the cycle process of an aircraft gas turbine. The power, efficiency, and other variables of the propulsion system are determined by merging the cycle processes of the propeller and the thermal management, as well as the energy conversion in the electric powertrain. We illustrate the capabilities of this approach through a sensitivity study of a small aircraft propulsion system with a required thrust of 1,000 N at a cruise speed of 85 m∕s. This study examines the impact of three exemplary design variables — cooling fan pressure ratio, heat exchanger frontal area and fuel cell current density — on the overall performance of the reference propulsion system. Optimal values for these design variables have been determined to achieve maximum efficiency and minimum propulsion system mass. For example, a thermal management design without a cooling fan has a lower overall efficiency (−18.2 %) and higher mass (+17.3%) compared to a design with a cooling fan pressure ratio of 1.04. In summary, this paper presents a method for designing the thermal management of a fuel cell propulsion system and discusses the impact of design variables on engine performance. The insights provided can help engineers to optimize fuel cell propulsion system design in terms of efficiency, mass, and hydrogen consumption.
- 24 February 2026
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 10, 29-49
Open AccessPerformance calculation of the thermal management system for a fuel cell aircraft engine
This paper presents a novel approach to the design of fuel cell thermal management systems, offering significant advantages for the evaluation of system architectures and design variables. The new performance calculation method considers the flow of cooling air as a separate cycle process. Analytical correlations are employed to describe the cycle process that the cooling air undergoes as it flows through the thermal management system, similar to the cycle process of an aircraft gas turbine. The power, efficiency, and other variables of the propulsion system are determined by merging the cycle processes of the propeller and the thermal management, as well as the energy conversion in the electric powertrain. We illustrate the capabilities of this approach through a sensitivity study of a small aircraft propulsion system with a required thrust of 1,000 N at a cruise speed of 85 m∕s. This study examines the impact of three exemplary design variables — cooling fan pressure ratio, heat exchanger frontal area and fuel cell current density — on the overall performance of the reference propulsion system. Optimal values for these design variables have been determined to achieve maximum efficiency and minimum propulsion system mass. For example, a thermal management design without a cooling fan has a lower overall efficiency (−18.2 %) and higher mass (+17.3%) compared to a design with a cooling fan pressure ratio of 1.04. In summary, this paper presents a method for designing the thermal management of a fuel cell propulsion system and discusses the impact of design variables on engine performance. The insights provided can help engineers to optimize fuel cell propulsion system design in terms of efficiency, mass, and hydrogen consumption.
- Open Access
- 17 November 2025
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 9, 213-223
Suction side film cooling measurements in a linear high-temperature cascade at near-engine conditions
Film-cooled turbine blades in a Linear High-Temperature Cascade are investigated experimentally and numerically at a Reynolds number of 120,000, low inlet Mach numbers (Ma=0.2), and main flow temperatures of up to 1,050K. Variations in cooling air temperature are used to achieve different density ratios. In addition, the cooling air mass flow is varied for different coolant mass flow ratios. The blades are derived from the mid-section of a high-pressure turbine blade and feature a single row of film cooling holes on the suction side. They are equipped with 66 thermocouples and 37 pressure taps. Film cooling reduces the material temperature in the region downstream of the holes up to 65% of the chord length. High mass ratios of MR>1.0% result in a reversal of the cooling effect due to the detachment of the cooling film. In summary, we provide temperature and pressure measurements of a film-cooled turbine blade at realistic density and mass flow ratios utilizing a unique linear cascade supplied with high-temperature exhaust gas flow. Our paper contributes to the validation of numerical codes used for the thermal design of turbine blades.
- 17 November 2025
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 9, 213-223
Open AccessSuction side film cooling measurements in a linear high-temperature cascade at near-engine conditions
Film-cooled turbine blades in a Linear High-Temperature Cascade are investigated experimentally and numerically at a Reynolds number of 120,000, low inlet Mach numbers (Ma=0.2), and main flow temperatures of up to 1,050K. Variations in cooling air temperature are used to achieve different density ratios. In addition, the cooling air mass flow is varied for different coolant mass flow ratios. The blades are derived from the mid-section of a high-pressure turbine blade and feature a single row of film cooling holes on the suction side. They are equipped with 66 thermocouples and 37 pressure taps. Film cooling reduces the material temperature in the region downstream of the holes up to 65% of the chord length. High mass ratios of MR>1.0% result in a reversal of the cooling effect due to the detachment of the cooling film. In summary, we provide temperature and pressure measurements of a film-cooled turbine blade at realistic density and mass flow ratios utilizing a unique linear cascade supplied with high-temperature exhaust gas flow. Our paper contributes to the validation of numerical codes used for the thermal design of turbine blades.
- Open Access
- 8 September 2025
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 17 (2) , 913-924
Reducing contrail formation by engine design and operating point adaptation of aircraft engines
In this paper, we present an analysis of the effect of engine design modifications and operating point adaptation mechanisms on the conditions in the engine exhaust plume, with a focus on contrail formation which is evaluated using the Schmidt-Appleman criterion. Our goal is to find ways to prevent contrail formation and thus reduce the climate impact of aviation. We use the gas turbine performance software GasTurb to model an aircraft engine of a contemporary short- to medium-range aircraft. We then examine several operating point adaption mechanisms with regard to their influence on the exhaust conditions and the resulting mixing line in the Schmidt-Appleman diagram. These are the bypass and core nozzle areas, high- and low-pressure turbine capacities, a handling bleed, and a high-pressure bleed. The main influence on the mixing line in the Schmidt-Appleman diagram is the change in exhaust jet temperature and its water content, which is affected by the fuel flow resulting from the engine’s operating point and efficiency. All measures are evaluated based on the shift in the critical altitude of contrail formation, with a minimum increase of 450 m in cruise flight conditions deemed necessary for any effective measure. We find that it is possible to reduce contrail formation. However, the critical altitude gains are only 57 m to 206 m for all measures investigated, which is insufficient to avoid contrail formation in practice, as calculated using the Schmidt-Appleman criterion. The measures also significantly increase specific fuel consumption, with more effective measures leading to higher increases of up to 35 %. Given the results presented, we find that engine operating point adaptations as examined in this paper are not suitable for contrail reduction due to their low effectiveness and significant increase in fuel consumption. More fundamental design changes, such as engine cycle adaptations or the use of hydrogen as a fuel, may offer greater potential for contrail reduction.
- 8 September 2025
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 17 (2) , 913-924
Open AccessReducing contrail formation by engine design and operating point adaptation of aircraft engines
In this paper, we present an analysis of the effect of engine design modifications and operating point adaptation mechanisms on the conditions in the engine exhaust plume, with a focus on contrail formation which is evaluated using the Schmidt-Appleman criterion. Our goal is to find ways to prevent contrail formation and thus reduce the climate impact of aviation. We use the gas turbine performance software GasTurb to model an aircraft engine of a contemporary short- to medium-range aircraft. We then examine several operating point adaption mechanisms with regard to their influence on the exhaust conditions and the resulting mixing line in the Schmidt-Appleman diagram. These are the bypass and core nozzle areas, high- and low-pressure turbine capacities, a handling bleed, and a high-pressure bleed. The main influence on the mixing line in the Schmidt-Appleman diagram is the change in exhaust jet temperature and its water content, which is affected by the fuel flow resulting from the engine’s operating point and efficiency. All measures are evaluated based on the shift in the critical altitude of contrail formation, with a minimum increase of 450 m in cruise flight conditions deemed necessary for any effective measure. We find that it is possible to reduce contrail formation. However, the critical altitude gains are only 57 m to 206 m for all measures investigated, which is insufficient to avoid contrail formation in practice, as calculated using the Schmidt-Appleman criterion. The measures also significantly increase specific fuel consumption, with more effective measures leading to higher increases of up to 35 %. Given the results presented, we find that engine operating point adaptations as examined in this paper are not suitable for contrail reduction due to their low effectiveness and significant increase in fuel consumption. More fundamental design changes, such as engine cycle adaptations or the use of hydrogen as a fuel, may offer greater potential for contrail reduction.
- Open Access
Manufacturing Considerations in the Aerodynamic Design Process of Turbomachinery Components
This paper presents a CFD-based method for the aerodynamic design of a high-pressure compressor rotor blisk, taking into account manufacturing constraints. Focus is placed on the influence of geometric deviations caused by the dynamic constraints of the milling machine. Special attention is given to the leading edge region of the blade, where high curvature results in increased sensitivity in both aerodynamic behavior and manufacturability. The generic blisk geometry on which this study is based is characterized by an elliptical leading edge. For the optimization, the leading edge is described by Bézier curves that transition smoothly to the suction and pressure sides with continuous curvature and a non-dimensional length ratio. In steady-state RANS parameter studies, the length ratio is systematically varied while the chord length is kept constant. For the aerodynamic evaluation of the design’s key performance parameters such as blade pressure distribution, total pressure loss and compressor efficiency are considered. To evaluate the machine dynamics for a given design, compliance with the nominal feed rate and the deviation between the planned and actual tool tip positions were used as evaluation parameters. Compared to the reference geometry with an elliptical leading edge, the purely aerodynamic optimization achieved an isentropic efficiency improvement of +0.24 percentage points in the aerodynamic design point and a profile deviation improvement of m in the 99th quantile. The interdisciplinary optimization achieved an improvement of +0.20 percentage points and m, respectively. This comparative study illustrates the potential of multidisciplinary design approaches that balance aerodynamic performance goals with manufacturability via a novel approach for Design-to-Manufacture-to-Design.Open AccessManufacturing Considerations in the Aerodynamic Design Process of Turbomachinery Components
This paper presents a CFD-based method for the aerodynamic design of a high-pressure compressor rotor blisk, taking into account manufacturing constraints. Focus is placed on the influence of geometric deviations caused by the dynamic constraints of the milling machine. Special attention is given to the leading edge region of the blade, where high curvature results in increased sensitivity in both aerodynamic behavior and manufacturability. The generic blisk geometry on which this study is based is characterized by an elliptical leading edge. For the optimization, the leading edge is described by Bézier curves that transition smoothly to the suction and pressure sides with continuous curvature and a non-dimensional length ratio. In steady-state RANS parameter studies, the length ratio is systematically varied while the chord length is kept constant. For the aerodynamic evaluation of the design’s key performance parameters such as blade pressure distribution, total pressure loss and compressor efficiency are considered. To evaluate the machine dynamics for a given design, compliance with the nominal feed rate and the deviation between the planned and actual tool tip positions were used as evaluation parameters. Compared to the reference geometry with an elliptical leading edge, the purely aerodynamic optimization achieved an isentropic efficiency improvement of +0.24 percentage points in the aerodynamic design point and a profile deviation improvement of m in the 99th quantile. The interdisciplinary optimization achieved an improvement of +0.20 percentage points and m, respectively. This comparative study illustrates the potential of multidisciplinary design approaches that balance aerodynamic performance goals with manufacturability via a novel approach for Design-to-Manufacture-to-Design. - 22 November 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (6) , 1-14
A Data-Driven Method for the Derivation of Explicit Algebraic Reynolds Stress Models Applied to the Wake Losses of Low-Pressure Turbine Cascades
This paper introduces and validates a data-driven approach to improve the prediction of linear eddy viscosity models (LEVMs). The general approach is adopted in order to improve the wake mixing of low-pressure turbine (LPT) cascades. The approach is based on the modification of the Boussinesq assumption. It follows the rationale applied in the derivation of explicit algebraic Reynolds stress models (EARSMs) by including additional second-order tensors, as suggested by Pope (1975, “A More General Effective-Viscosity Hypothesis,” J. Fluid Mech., 72(2), pp. 331–340. 10.1017/S0022112075003382 ) . The unknown scalar functions that determine the contributions of each second-order tensor to the Reynolds stresses are approximated as polynomials. A metamodel-assisted multi-objective optimization determines the value of each of the polynomial coefficients. The optimization minimizes the difference between the result of the EARSM simulation and reference data provided by a high-fidelity large eddy simulation (LES). In this study, tailor made EARSMs are calibrated in order to improve the prediction of the kinetic energy loss distribution in the wake of the T106C LPT cascade with an isentropic Reynolds number of 80,000. We showed that the wake losses predicted by state-of-the-art Reynolds-averaged Navier–Stokes (RANS) turbulence models cannot reproduce the reference (LES) data. In the following, we investigated the influence of each polynomial coefficient of the (EARSM) on the flow solutions within a sensitivity study. The models generated by the approach reduced the deviations in total kinetic energy loss between the (LES) reference solution and the baseline model by approximately 70%. The turbulent quantities are analyzed to identify the physical correlations between the model inputs and the improvement. The transferability of the models to unseen test cases was assessed using the MTU-T161 (LPT) cascade with an isentropic Reynolds number of 90,000. A decrease of up to 80% is achieved regarding the deviations between the (LES) reference and the baseline RANS model. In summary, the suggested approach was able to generate tailor made EARSM models that reduce the deviations between RANS and LES for the mixing of turbulent wake flows.
- 22 November 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (6) , 1-14
A Data-Driven Method for the Derivation of Explicit Algebraic Reynolds Stress Models Applied to the Wake Losses of Low-Pressure Turbine Cascades
This paper introduces and validates a data-driven approach to improve the prediction of linear eddy viscosity models (LEVMs). The general approach is adopted in order to improve the wake mixing of low-pressure turbine (LPT) cascades. The approach is based on the modification of the Boussinesq assumption. It follows the rationale applied in the derivation of explicit algebraic Reynolds stress models (EARSMs) by including additional second-order tensors, as suggested by Pope (1975, “A More General Effective-Viscosity Hypothesis,” J. Fluid Mech., 72(2), pp. 331–340. 10.1017/S0022112075003382 ) . The unknown scalar functions that determine the contributions of each second-order tensor to the Reynolds stresses are approximated as polynomials. A metamodel-assisted multi-objective optimization determines the value of each of the polynomial coefficients. The optimization minimizes the difference between the result of the EARSM simulation and reference data provided by a high-fidelity large eddy simulation (LES). In this study, tailor made EARSMs are calibrated in order to improve the prediction of the kinetic energy loss distribution in the wake of the T106C LPT cascade with an isentropic Reynolds number of 80,000. We showed that the wake losses predicted by state-of-the-art Reynolds-averaged Navier–Stokes (RANS) turbulence models cannot reproduce the reference (LES) data. In the following, we investigated the influence of each polynomial coefficient of the (EARSM) on the flow solutions within a sensitivity study. The models generated by the approach reduced the deviations in total kinetic energy loss between the (LES) reference solution and the baseline model by approximately 70%. The turbulent quantities are analyzed to identify the physical correlations between the model inputs and the improvement. The transferability of the models to unseen test cases was assessed using the MTU-T161 (LPT) cascade with an isentropic Reynolds number of 90,000. A decrease of up to 80% is achieved regarding the deviations between the (LES) reference and the baseline RANS model. In summary, the suggested approach was able to generate tailor made EARSM models that reduce the deviations between RANS and LES for the mixing of turbulent wake flows.
- Open Access
- 14 November 2024
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 8, 456-470
Flow disturbance by intrusive instrumentation located on the surface of a compressor blade
In this paper, we present an experimental and numerical investigation into the flow disturbance by intrusive instrumentation in the form of spanwise pressure tubes mounted on the pressure and suction side of a compressor blade in a linear cascade wind tunnel at a moderate subsonic Mach number of 0.5 and a Reynolds number of 790,000. The pressure tubes were modelled as simplified bumps extending over the entire span with a width of 24% of the chord length and a height of 67% of the maximum blade thickness. The leading edge of the bumps is located at 30% of the streamwise surface length. We found that the total pressure losses generated by these pressure tubes are considerably larger when they are placed on the suction side of the blade. The suction-sided bump increases the total pressure loss coefficient by a factor of four, while the pressure-sided bump approximately doubles it. CFD simulations reveal that the suction-sided bump causes the flow to form a large, open recirculation zone, while for the pressure-sided bump, the flow reattaches near the trailing edge. In conclusion, we provide insights into the effects of pressure tubes on the losses generated by compressor blades. The mounted tubes significantly impact the flow and should be carefully considered during instrumentation design.
- 14 November 2024
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 8, 456-470
Open AccessFlow disturbance by intrusive instrumentation located on the surface of a compressor blade
In this paper, we present an experimental and numerical investigation into the flow disturbance by intrusive instrumentation in the form of spanwise pressure tubes mounted on the pressure and suction side of a compressor blade in a linear cascade wind tunnel at a moderate subsonic Mach number of 0.5 and a Reynolds number of 790,000. The pressure tubes were modelled as simplified bumps extending over the entire span with a width of 24% of the chord length and a height of 67% of the maximum blade thickness. The leading edge of the bumps is located at 30% of the streamwise surface length. We found that the total pressure losses generated by these pressure tubes are considerably larger when they are placed on the suction side of the blade. The suction-sided bump increases the total pressure loss coefficient by a factor of four, while the pressure-sided bump approximately doubles it. CFD simulations reveal that the suction-sided bump causes the flow to form a large, open recirculation zone, while for the pressure-sided bump, the flow reattaches near the trailing edge. In conclusion, we provide insights into the effects of pressure tubes on the losses generated by compressor blades. The mounted tubes significantly impact the flow and should be carefully considered during instrumentation design.
- 19 September 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (1) , 1-11
Teaching Aero-Engine Performance: From Analytics to Hands-On Exercises Using Gas Turbine Performance Software
In this paper, we present an approach for teaching turbojet engine performance that combines mathematical analysis with the use of performance software to provide students with a comprehensive and in-depth understanding of engine performance and how it is affected by design parameter choices. In the first part, we present the derivation of a universally valid analytical model for turbojet engine cycle design, which is the basis of the propulsion courses at RWTH Aachen University. The analytical model allows for the calculation of specific thrust as well as thermal and propulsive efficiencies as a function of pressure ratios and burner exit temperature. These are all expressed as differentiable functions. Their mathematical extremes form a basis for examining the intricate relationships in turbojet engine design. In the second part, we move from theory to practice. We utilize the GasTurb software, computing turbojet engine cycles for a wide range of cycle design parameters. The analytically derived trends are validated and errors introduced by simplifications are assessed. Differences between the analytical approach and software-based performance simulations of real engines, like temperature-dependent gas properties and secondary air systems, are emphasized and discussed, thus providing a bridge to real-world applications. In summary, this paper describes a two-step approach to teaching turbojet engine design using analytics and performance software. Each approach alone can be used to enrich and extend existing performance courses. Combining the approaches has significant benefits, improving understanding and inspiring students to pursue further research in the field of propulsion.
- 19 September 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (1) , 1-11
Teaching Aero-Engine Performance: From Analytics to Hands-On Exercises Using Gas Turbine Performance Software
In this paper, we present an approach for teaching turbojet engine performance that combines mathematical analysis with the use of performance software to provide students with a comprehensive and in-depth understanding of engine performance and how it is affected by design parameter choices. In the first part, we present the derivation of a universally valid analytical model for turbojet engine cycle design, which is the basis of the propulsion courses at RWTH Aachen University. The analytical model allows for the calculation of specific thrust as well as thermal and propulsive efficiencies as a function of pressure ratios and burner exit temperature. These are all expressed as differentiable functions. Their mathematical extremes form a basis for examining the intricate relationships in turbojet engine design. In the second part, we move from theory to practice. We utilize the GasTurb software, computing turbojet engine cycles for a wide range of cycle design parameters. The analytically derived trends are validated and errors introduced by simplifications are assessed. Differences between the analytical approach and software-based performance simulations of real engines, like temperature-dependent gas properties and secondary air systems, are emphasized and discussed, thus providing a bridge to real-world applications. In summary, this paper describes a two-step approach to teaching turbojet engine design using analytics and performance software. Each approach alone can be used to enrich and extend existing performance courses. Combining the approaches has significant benefits, improving understanding and inspiring students to pursue further research in the field of propulsion.
- 30 November 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (1) , 1-12
Assessment of the DDES- γ Model for the Simulation of a Highly Loaded Turbine Cascade
The flow over the linear low-pressure turbine cascade MTU-T161 at Re = 90,000 is analyzed using delayed detached eddy simulations (DDES). At this operating point, the low Reynolds number and the high loading of the blade result in a separation bubble and a separation-induced transition of the flow over the suction side. The utilized DDES method is based on a vorticity-based formulation to calculate the subgrid length scales, and it incorporates the one-equation γ-transition model. The computational model of the MTU-T161 cascade consists of one blade passage, including the diverging viscous sidewalls. To reproduce realistic operating conditions and to mimic the experiments, synthetic turbulence is prescribed at the inlet of the computational domain. Several studies are performed to assess the accuracy and performance of the DDES one-equation γ-transition model against experimental data and a benchmark large eddy simulations (LES). The primary focus is on the prediction of the separation and the separation-induced transition mechanism. First of all, a systematic grid convergence study is conducted and grid criteria are derived in order to ensure a satisfactory agreement of the flow metrics, such as isentropic Mach number, friction coefficient distribution, and total pressure wake losses at mid-span with experimental data. Furthermore, a detailed analysis of the DDES model parameters, such as shielding function and subgrid length scale, is presented and the effect of these parameters on the prediction accuracy of the separation bubble region is analyzed. The analysis of the suction side boundary layer indicates that the turbulent kinetic energy should be resolved and modeled properly in order to represent the separation bubble correctly. In particular, the correct prediction of the separated shear layer above the separation bubble is of utmost importance. The results of the simulations reveal higher demands on grid resolution for such transitional flows than typically have been reported in the literature for turbulent boundary layers. This higher demand on grid resolution results in more expensive simulations than Reynolds-averaged Navier–Stokes (RANS). Nevertheless, DDES requires less computing time than wall-resolved LES. Additionally, the results of the transitional DDES model are compared to DDES without a transition model, an RANS eddy viscosity model, and a reference LES. The results show that the DDES approach needs to be coupled with a transition model, such as the one-equation γ-transition model, in order to capture the flow topology over a highly loaded turbine blade correctly. The benefit of the DDES one-equation γ-transition model becomes particularly evident when predicting the separated shear layer, the transition process, and the subsequent reattachment. The RANS eddy viscosity turbulence and transition models applied within our study are not able to predict the aforementioned mechanisms accurately. For highly loaded turbine blades in particular, the accurate prediction of flow separation and potential reattachment is crucial for the aerodynamic design of turbines, since large parts of the total pressure loss are generated in the separated region. For this reason, the DDES one-equation γ-transition model can be a good compromise in terms of predictive accuracy and computational costs.
- 30 November 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (1) , 1-12
Assessment of the DDES- γ Model for the Simulation of a Highly Loaded Turbine Cascade
The flow over the linear low-pressure turbine cascade MTU-T161 at Re = 90,000 is analyzed using delayed detached eddy simulations (DDES). At this operating point, the low Reynolds number and the high loading of the blade result in a separation bubble and a separation-induced transition of the flow over the suction side. The utilized DDES method is based on a vorticity-based formulation to calculate the subgrid length scales, and it incorporates the one-equation γ-transition model. The computational model of the MTU-T161 cascade consists of one blade passage, including the diverging viscous sidewalls. To reproduce realistic operating conditions and to mimic the experiments, synthetic turbulence is prescribed at the inlet of the computational domain. Several studies are performed to assess the accuracy and performance of the DDES one-equation γ-transition model against experimental data and a benchmark large eddy simulations (LES). The primary focus is on the prediction of the separation and the separation-induced transition mechanism. First of all, a systematic grid convergence study is conducted and grid criteria are derived in order to ensure a satisfactory agreement of the flow metrics, such as isentropic Mach number, friction coefficient distribution, and total pressure wake losses at mid-span with experimental data. Furthermore, a detailed analysis of the DDES model parameters, such as shielding function and subgrid length scale, is presented and the effect of these parameters on the prediction accuracy of the separation bubble region is analyzed. The analysis of the suction side boundary layer indicates that the turbulent kinetic energy should be resolved and modeled properly in order to represent the separation bubble correctly. In particular, the correct prediction of the separated shear layer above the separation bubble is of utmost importance. The results of the simulations reveal higher demands on grid resolution for such transitional flows than typically have been reported in the literature for turbulent boundary layers. This higher demand on grid resolution results in more expensive simulations than Reynolds-averaged Navier–Stokes (RANS). Nevertheless, DDES requires less computing time than wall-resolved LES. Additionally, the results of the transitional DDES model are compared to DDES without a transition model, an RANS eddy viscosity model, and a reference LES. The results show that the DDES approach needs to be coupled with a transition model, such as the one-equation γ-transition model, in order to capture the flow topology over a highly loaded turbine blade correctly. The benefit of the DDES one-equation γ-transition model becomes particularly evident when predicting the separated shear layer, the transition process, and the subsequent reattachment. The RANS eddy viscosity turbulence and transition models applied within our study are not able to predict the aforementioned mechanisms accurately. For highly loaded turbine blades in particular, the accurate prediction of flow separation and potential reattachment is crucial for the aerodynamic design of turbines, since large parts of the total pressure loss are generated in the separated region. For this reason, the DDES one-equation γ-transition model can be a good compromise in terms of predictive accuracy and computational costs.
- Open Access
- 24 July 2023
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 7, 222-241
Comparison of LDA and hot-wire measurements at moderate subsonic mach numbers
A detailed comparison of Hot-Wire-Anemometry (HWA) and Laser-Doppler-Anemometry (LDA) measurements in the wake of an airfoil is presented. An evaluation of the capabilities of both techniques in measuring three-dimensional turbulence in turbomachinery applications is made and potential...
- 24 July 2023
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 7, 222-241
Open AccessComparison of LDA and hot-wire measurements at moderate subsonic mach numbers
A detailed comparison of Hot-Wire-Anemometry (HWA) and Laser-Doppler-Anemometry (LDA) measurements in the wake of an airfoil is presented. An evaluation of the capabilities of both techniques in measuring three-dimensional turbulence in turbomachinery applications is made and potential...