Tárcio dos Santos Cabral
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tárcio dos Santos Cabral has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Eduardo de Magalhães Braga
Universidade federal do Pará
5 shared publications - Ademir Angelo Castro Filho
Universidade Federal do Pará (UFPA)
2 shared publications - Diego Jorge Alves Borges
Universidade Federal do Pará (UFPA)
2 shared publications - Ednelson da Silva Costa
FEI – UFPA
2 shared publications - Lino Alberto Soares Rodrigues2 shared publications
- Paola Evelen Costa Baia
Universidade Federal do Pará (UFPA)
2 shared publications
Latest Publications
- Open Access
- 2 May 2025
- Published by Brazilian Journals in REVISTA DELOS
- Vol. 18 (67) , e5292
Acoustic anisotropy as a factor to determine residual stresses in GMAW and CW-GMAW welds
In the areas of construction and maintenance of welded implements, the acoustic anisotropy of the as received material exerts a great influence on the generated residual stresses levels. In this context, several measurements were taken in order to obtain the acoustic anisotropy, as well as the residual stresses values of welds in simple deposition performed via GMAW (Gas Metal Arc Welding) and CW-GMAW (Cold Wire-Gas Metal Arc Welding). The acoustic anisotropy of the present material, ASTM 131 steel, was determined before and after the welding process using an ultrasonic technique called acoustic birefringence. It was verified that the stress levels at the same point varied with four adopted anisotropy parameters (punctual, mean, maximum and minimum). The maximum stress difference (σE) obtained at the same point with the maximum and minimum anisotropy was about 38 MPa, and for the mean and punctual, the maximum stress was 21 MPa. It is assumed that the non-uniform distribution of acoustic anisotropy in the as received material has generated such stresses variation. The punctual or mean anisotropy of the as received material is the most recommended to be used in the stresses calculations, as the maximum stresses difference calculated by these values represented an only 6%, error, whereas the maximum and minimum anisotropy obtained an error of 11% in relation to the yield strength of the material.
- 2 May 2025
- Published by Brazilian Journals in REVISTA DELOS
- Vol. 18 (67) , e5292
Open AccessAcoustic anisotropy as a factor to determine residual stresses in GMAW and CW-GMAW welds
In the areas of construction and maintenance of welded implements, the acoustic anisotropy of the as received material exerts a great influence on the generated residual stresses levels. In this context, several measurements were taken in order to obtain the acoustic anisotropy, as well as the residual stresses values of welds in simple deposition performed via GMAW (Gas Metal Arc Welding) and CW-GMAW (Cold Wire-Gas Metal Arc Welding). The acoustic anisotropy of the present material, ASTM 131 steel, was determined before and after the welding process using an ultrasonic technique called acoustic birefringence. It was verified that the stress levels at the same point varied with four adopted anisotropy parameters (punctual, mean, maximum and minimum). The maximum stress difference (σE) obtained at the same point with the maximum and minimum anisotropy was about 38 MPa, and for the mean and punctual, the maximum stress was 21 MPa. It is assumed that the non-uniform distribution of acoustic anisotropy in the as received material has generated such stresses variation. The punctual or mean anisotropy of the as received material is the most recommended to be used in the stresses calculations, as the maximum stresses difference calculated by these values represented an only 6%, error, whereas the maximum and minimum anisotropy obtained an error of 11% in relation to the yield strength of the material.
- Open Access
- 16 August 2024
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 25 (16) , 8910
Morphographic Changes in the Electrocardiogram of Colossoma macropomum Caused by Exposure to Manganese
Manganese (Mn2+) is an abundant chemical element in the earth’s crust and is present in soil, water, and industrial environments, including mining, welding, and battery manufacturing. Manganese (Mn) is an essential metal needed as a cofactor for many enzymes to maintain proper biological functions. Excessive exposure to Mn in high doses can result in a condition known as manganism, which results in disorders of the neurological, cardiac, and pulmonary systems. The aim of this study was to assess cardiac susceptibility to manganese intoxication in Colossoma macropomum subjected to a fixed concentration of 4 mg/mL for a period of up to 96 h. This study used 45 Tambaquis (30.38 ± 3.5 g) divided into five groups of 9 animals/treatment. The treated groups were exposed to the manganese concentration for a period of 24, 48, 72, and 96 h, after which the animals’ ECGs were recorded, showing heart rate, R-R interval, P-Q interval, QRS complex duration and S-T interval. The results showed that cardiac activity decreased as the contact time increased, with an increase in the P-Q and S-T intervals. This indicates that the breakdown of circulatory homeostasis in these animals was caused by contact time with manganese.
- 16 August 2024
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 25 (16) , 8910
Open AccessMorphographic Changes in the Electrocardiogram of Colossoma macropomum Caused by Exposure to Manganese
Manganese (Mn2+) is an abundant chemical element in the earth’s crust and is present in soil, water, and industrial environments, including mining, welding, and battery manufacturing. Manganese (Mn) is an essential metal needed as a cofactor for many enzymes to maintain proper biological functions. Excessive exposure to Mn in high doses can result in a condition known as manganism, which results in disorders of the neurological, cardiac, and pulmonary systems. The aim of this study was to assess cardiac susceptibility to manganese intoxication in Colossoma macropomum subjected to a fixed concentration of 4 mg/mL for a period of up to 96 h. This study used 45 Tambaquis (30.38 ± 3.5 g) divided into five groups of 9 animals/treatment. The treated groups were exposed to the manganese concentration for a period of 24, 48, 72, and 96 h, after which the animals’ ECGs were recorded, showing heart rate, R-R interval, P-Q interval, QRS complex duration and S-T interval. The results showed that cardiac activity decreased as the contact time increased, with an increase in the P-Q and S-T intervals. This indicates that the breakdown of circulatory homeostasis in these animals was caused by contact time with manganese.
- Open Access
- 23 June 2022
- Published by IntechOpen
A Brief Study of Unconventional Variants of GMAW Welding: Parameters, Weld Bead, and Microstructures
The GMAW (Gas Metal Arc Welding) process is an electric arc welding technique widely used around the world due to its ease of use, low equipment cost and, mainly, due to the high deposition rate, the quality of the metal of solder, which makes it versatile and susceptible to modification. Thus, variants such as CW-GMAW (Cold Wire–Gas Metal Arc Welding), DCW-GMAW (Double Cold Wire–Gas Metal Arc Welding), and HW-GMAW (Hot Wire–Gas Metal Arc Welding) emerged from the conception of small adaptations to the original process that ended up generating better and more adjusted results than GMAW. Thus, variations of some parameters will be shown and their respective effects on the weld bead geometry, dilution, penetration, deposition rate, in addition to the effects on macro and microstructure. This provides the possibility of using the variants in different types of applications in the industry in general. Where the application in narrow 4 mm chamfer has already been observed, reduction of residual stresses, increase in fatigue resistance and coatings with special alloys.
- 23 June 2022
- Published by IntechOpen
Open AccessA Brief Study of Unconventional Variants of GMAW Welding: Parameters, Weld Bead, and Microstructures
The GMAW (Gas Metal Arc Welding) process is an electric arc welding technique widely used around the world due to its ease of use, low equipment cost and, mainly, due to the high deposition rate, the quality of the metal of solder, which makes it versatile and susceptible to modification. Thus, variants such as CW-GMAW (Cold Wire–Gas Metal Arc Welding), DCW-GMAW (Double Cold Wire–Gas Metal Arc Welding), and HW-GMAW (Hot Wire–Gas Metal Arc Welding) emerged from the conception of small adaptations to the original process that ended up generating better and more adjusted results than GMAW. Thus, variations of some parameters will be shown and their respective effects on the weld bead geometry, dilution, penetration, deposition rate, in addition to the effects on macro and microstructure. This provides the possibility of using the variants in different types of applications in the industry in general. Where the application in narrow 4 mm chamfer has already been observed, reduction of residual stresses, increase in fatigue resistance and coatings with special alloys.
- Open Access
- 8 October 2018
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 40 (11) , 511
Correction to: Influence of a cobalt-based wire injection in austenitic coating deposited via CW-GMAW
- 8 October 2018
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 40 (11) , 511
Open AccessCorrection to: Influence of a cobalt-based wire injection in austenitic coating deposited via CW-GMAW
- 30 August 2018
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 40 (9) , 461
Influence of a cobalt-based wire injection in austenitic coating deposited via CW-GMAW
- 30 August 2018
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 40 (9) , 461
Influence of a cobalt-based wire injection in austenitic coating deposited via CW-GMAW
- Open Access
- 1 December 2013
- Published by FapUNIFESP (SciELO) in Soldagem & Inspeção
- Vol. 18 (4) , 339-348
Influência dos procedimentos e modos de transferência no processo MAG na redução de deformações em painéis de estruturas navais
Juntamente com o crescimento da indústria naval brasileira surgiram problemas provenientes dos processos de produção na forma de distorções e tensões residuais. Neste trabalho foi estudada a influência de procedimentos de soldagem (sequência e direção de soldagem e uso do passe reverso) e modos de transferência (MAG-CC, MAG-STT e MAG-CW) sobre os valores de distorções. Todas as soldagens foram realizadas com o arame ER70S-6 e gás de proteção CO2 puro no modo curto-circuito. Ao final das soldagens, observou-se que a variável mais importante foi a mudança de direção de soldagem, que está ligada diretamente aos níveis de restrição do painel teste. As sequências utilizadas surtiram pouco efeito nos valores de distorção. O passe reverso obteve valores baixos de distorção, contudo, mostrou-se improdutivo. Observou-se que os valores de distorção para os processos e MAG-STT resultaram em valores de distorção semelhantes. Os painéis soldados pelo processo MAG-CW obtiveram os menores valores de distorção mensurados.
- 1 December 2013
- Published by FapUNIFESP (SciELO) in Soldagem & Inspeção
- Vol. 18 (4) , 339-348
Open AccessInfluência dos procedimentos e modos de transferência no processo MAG na redução de deformações em painéis de estruturas navais
Juntamente com o crescimento da indústria naval brasileira surgiram problemas provenientes dos processos de produção na forma de distorções e tensões residuais. Neste trabalho foi estudada a influência de procedimentos de soldagem (sequência e direção de soldagem e uso do passe reverso) e modos de transferência (MAG-CC, MAG-STT e MAG-CW) sobre os valores de distorções. Todas as soldagens foram realizadas com o arame ER70S-6 e gás de proteção CO2 puro no modo curto-circuito. Ao final das soldagens, observou-se que a variável mais importante foi a mudança de direção de soldagem, que está ligada diretamente aos níveis de restrição do painel teste. As sequências utilizadas surtiram pouco efeito nos valores de distorção. O passe reverso obteve valores baixos de distorção, contudo, mostrou-se improdutivo. Observou-se que os valores de distorção para os processos e MAG-STT resultaram em valores de distorção semelhantes. Os painéis soldados pelo processo MAG-CW obtiveram os menores valores de distorção mensurados.