Eduardo de Magalhães Braga
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Eduardo de Magalhães Braga has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Tárcio dos Santos Cabral
Universidade Federal do Pará (UFPA)
5 shared publications - Ademir Angelo Castro Filho
Universidade Federal do Pará (UFPA)
4 shared publications - Ednelson da Silva Costa
FEI – UFPA
4 shared publications - Lino Alberto Soares Rodrigues4 shared publications
- Diego Jorge Alves Borges
Universidade Federal do Pará (UFPA)
2 shared publications - Paola Evelen Costa Baia
Universidade Federal do Pará (UFPA)
2 shared publications
Latest Publications
- Open Access
- 2 May 2025
- Published by Brazilian Journals in REVISTA DELOS
- Vol. 18 (67) , e5292
Acoustic anisotropy as a factor to determine residual stresses in GMAW and CW-GMAW welds
In the areas of construction and maintenance of welded implements, the acoustic anisotropy of the as received material exerts a great influence on the generated residual stresses levels. In this context, several measurements were taken in order to obtain the acoustic anisotropy, as well as the residual stresses values of welds in simple deposition performed via GMAW (Gas Metal Arc Welding) and CW-GMAW (Cold Wire-Gas Metal Arc Welding). The acoustic anisotropy of the present material, ASTM 131 steel, was determined before and after the welding process using an ultrasonic technique called acoustic birefringence. It was verified that the stress levels at the same point varied with four adopted anisotropy parameters (punctual, mean, maximum and minimum). The maximum stress difference (σE) obtained at the same point with the maximum and minimum anisotropy was about 38 MPa, and for the mean and punctual, the maximum stress was 21 MPa. It is assumed that the non-uniform distribution of acoustic anisotropy in the as received material has generated such stresses variation. The punctual or mean anisotropy of the as received material is the most recommended to be used in the stresses calculations, as the maximum stresses difference calculated by these values represented an only 6%, error, whereas the maximum and minimum anisotropy obtained an error of 11% in relation to the yield strength of the material.
- 2 May 2025
- Published by Brazilian Journals in REVISTA DELOS
- Vol. 18 (67) , e5292
Open AccessAcoustic anisotropy as a factor to determine residual stresses in GMAW and CW-GMAW welds
In the areas of construction and maintenance of welded implements, the acoustic anisotropy of the as received material exerts a great influence on the generated residual stresses levels. In this context, several measurements were taken in order to obtain the acoustic anisotropy, as well as the residual stresses values of welds in simple deposition performed via GMAW (Gas Metal Arc Welding) and CW-GMAW (Cold Wire-Gas Metal Arc Welding). The acoustic anisotropy of the present material, ASTM 131 steel, was determined before and after the welding process using an ultrasonic technique called acoustic birefringence. It was verified that the stress levels at the same point varied with four adopted anisotropy parameters (punctual, mean, maximum and minimum). The maximum stress difference (σE) obtained at the same point with the maximum and minimum anisotropy was about 38 MPa, and for the mean and punctual, the maximum stress was 21 MPa. It is assumed that the non-uniform distribution of acoustic anisotropy in the as received material has generated such stresses variation. The punctual or mean anisotropy of the as received material is the most recommended to be used in the stresses calculations, as the maximum stresses difference calculated by these values represented an only 6%, error, whereas the maximum and minimum anisotropy obtained an error of 11% in relation to the yield strength of the material.
- Open Access
- 1 April 2025
- Published by Brazilian Journals in REVISTA FOCO
- Vol. 18 (4) , e8201
ANÁLISE DO TEMPO DE PROPAGAÇÃO DA ONDA E DA BIRREFRINGÊNCIA ACÚSTICA EM DIFERENTES SUPERFICIES DO AÇO CARBONO
A técnica de inspeção pulso-eco usada pelo método ultrassônico é aplicada para diversos fins, como detecção e análise de falhas e medição de tensões, residuais e aplicadas, em materiais metálicos, e como a superfície destes materiais se apresentam, geralmente, comprometidas por rugosidade e camadas de tintas e de óxidos, por exemplo, então, para a análise não destrutiva por ultrassom através da técnica pulso-eco, usando-se o transdutor de contato, a superfície desses materiais necessita estar devidamente preparada para não comprometer a análise. Nesse sentido, este trabalho tem como objetivo analisar o comportamento do tempo de propagação da onda ultrassônica cisalhante e da birrefringência acústica pós limpeza da superficie do aço ASTM A-131 com lixamentos e polimentos, mecânico e eletrolítico. Como resultados, verificou-se que o tempo da onda ultrassônica após o eletropolimento reduziu em aproximadamente 30 ns em relação ao tempo do material como recebido. Além disso, os valores de birrefringência acústica obtidos foram considerados estatisticamente iguais para todas as condições de superfície do aço, indicando que não há necessidade de uma limpeza aprimorada da superfície do material para a medição do tempo de percurso da onda e de birrefringência acústica.
- 1 April 2025
- Published by Brazilian Journals in REVISTA FOCO
- Vol. 18 (4) , e8201
Open AccessANÁLISE DO TEMPO DE PROPAGAÇÃO DA ONDA E DA BIRREFRINGÊNCIA ACÚSTICA EM DIFERENTES SUPERFICIES DO AÇO CARBONO
A técnica de inspeção pulso-eco usada pelo método ultrassônico é aplicada para diversos fins, como detecção e análise de falhas e medição de tensões, residuais e aplicadas, em materiais metálicos, e como a superfície destes materiais se apresentam, geralmente, comprometidas por rugosidade e camadas de tintas e de óxidos, por exemplo, então, para a análise não destrutiva por ultrassom através da técnica pulso-eco, usando-se o transdutor de contato, a superfície desses materiais necessita estar devidamente preparada para não comprometer a análise. Nesse sentido, este trabalho tem como objetivo analisar o comportamento do tempo de propagação da onda ultrassônica cisalhante e da birrefringência acústica pós limpeza da superficie do aço ASTM A-131 com lixamentos e polimentos, mecânico e eletrolítico. Como resultados, verificou-se que o tempo da onda ultrassônica após o eletropolimento reduziu em aproximadamente 30 ns em relação ao tempo do material como recebido. Além disso, os valores de birrefringência acústica obtidos foram considerados estatisticamente iguais para todas as condições de superfície do aço, indicando que não há necessidade de uma limpeza aprimorada da superfície do material para a medição do tempo de percurso da onda e de birrefringência acústica.
- Open Access
- 1 January 2025
- Published by National Library of Serbia in Journal of Mining and Metallurgy, Section B: Metallurgy
- Vol. 61 (3) , 293-302
Effects of welding parameters on percentage dilution and mechanical properties in welded joints of ultra-high hardness armour steels
This study investigates the effects of Gas Metal Arc Welding (GMAW) parameters?specifically welding speed and stickout? on the dilution and mechanical properties of welded joints composed of ultra-high hardness quenched and tempered (UHH-Q&T) armor steel and austenitic stainless steel filler metal. An optimization methodology was used to set constant parameters, including wire diameter, gas flow rate, welding voltage, and wire feed speed, based on equipment capabilities. Experimental trials varied welding speed and electrode stick-out while maintaining a constant current through inductance control. Although the welding parameters affected the melted base and filler metal areas, the dilution percentage remained unaffected. The correlation between dilution and welding current was validated. Microstructural and mechanical analyses confirmed the consistent behavior of the welded joints under the tested conditions.
- 1 January 2025
- Published by National Library of Serbia in Journal of Mining and Metallurgy, Section B: Metallurgy
- Vol. 61 (3) , 293-302
Open AccessEffects of welding parameters on percentage dilution and mechanical properties in welded joints of ultra-high hardness armour steels
This study investigates the effects of Gas Metal Arc Welding (GMAW) parameters?specifically welding speed and stickout? on the dilution and mechanical properties of welded joints composed of ultra-high hardness quenched and tempered (UHH-Q&T) armor steel and austenitic stainless steel filler metal. An optimization methodology was used to set constant parameters, including wire diameter, gas flow rate, welding voltage, and wire feed speed, based on equipment capabilities. Experimental trials varied welding speed and electrode stick-out while maintaining a constant current through inductance control. Although the welding parameters affected the melted base and filler metal areas, the dilution percentage remained unaffected. The correlation between dilution and welding current was validated. Microstructural and mechanical analyses confirmed the consistent behavior of the welded joints under the tested conditions.
- Open Access
- 2 December 2024
- Published by Brazilian Journals in REVISTA FOCO
- Vol. 17 (12) , e7356
IMPLEMENTAÇÃO DA EFICIÊNCIA GLOBAL DO EQUIPAMENTO (OEE) EM UMA EMPRESA DE ABATE DE FRANGO NO PARÁ
A avicultura brasileira enfrenta desafios significativos relacionados à eficiência operacional, especialmente em empresas de abate de frango, onde perdas de produtividade impactam diretamente a rentabilidade do setor. Este artigo teve como objetivo implementar o indicador de Eficiência Global do Equipamento (OEE) em uma planta de abate de frango localizada no estado do Pará, buscando identificar as principais causas de ineficiência e propor soluções para uma gestão mais eficaz. A metodologia incluiu revisão bibliográfica, coleta de dados no chão de fábrica, cálculo do OEE e análise das principais falhas operacionais. Os resultados identificaram o setor de recepção de aves como o maior contribuinte para paradas não planejadas, devido a falhas na Nória da Plataforma, manutenções corretivas emergenciais, ausência de processos padronizados, falta de treinamento e problemas de comunicação. Como medidas corretivas, goram implementados controles de velocidade das nórias e um sistema de gerenciamento de custos, reforçando o OEE como ferramenta estratégica para identificar gargalos e aumentar a competitividade no setor avícola.
- 2 December 2024
- Published by Brazilian Journals in REVISTA FOCO
- Vol. 17 (12) , e7356
Open AccessIMPLEMENTAÇÃO DA EFICIÊNCIA GLOBAL DO EQUIPAMENTO (OEE) EM UMA EMPRESA DE ABATE DE FRANGO NO PARÁ
A avicultura brasileira enfrenta desafios significativos relacionados à eficiência operacional, especialmente em empresas de abate de frango, onde perdas de produtividade impactam diretamente a rentabilidade do setor. Este artigo teve como objetivo implementar o indicador de Eficiência Global do Equipamento (OEE) em uma planta de abate de frango localizada no estado do Pará, buscando identificar as principais causas de ineficiência e propor soluções para uma gestão mais eficaz. A metodologia incluiu revisão bibliográfica, coleta de dados no chão de fábrica, cálculo do OEE e análise das principais falhas operacionais. Os resultados identificaram o setor de recepção de aves como o maior contribuinte para paradas não planejadas, devido a falhas na Nória da Plataforma, manutenções corretivas emergenciais, ausência de processos padronizados, falta de treinamento e problemas de comunicação. Como medidas corretivas, goram implementados controles de velocidade das nórias e um sistema de gerenciamento de custos, reforçando o OEE como ferramenta estratégica para identificar gargalos e aumentar a competitividade no setor avícola.
- Open Access
- 24 October 2024
- Published by Springer Nature in Research Square
Analysis of the plane stress state by combined ultrasonic waves
This study investigates the measurement of the residual stress state in ASTM A131 steel plates using a non-destructive technique based on the combination of ultrasonic waves. The method combines shear and compressive waves to more accurately assess the stress state of the material after heat application via TIG welding. Measurements were taken at different points on the plate using transducers attached to a stepper motor, which enabled the rotation of the transducer and precise determination of the wave propagation angle. The results showed that residual stresses were more concentrated near the weld zone and the supports that held the sample, while areas farther away showed significantly lower stresses. The technique proved effective in measuring the residual stress state, overcoming the limitations of traditional methods, which often estimate only the differences between principal stresses. This approach has the potential to be applied in various industries, particularly in sectors that require accurate stress evaluations in structural components, such as naval construction. The combined use of shear and compressive waves offers a non-destructive and highly precise alternative to ensure the integrity and durability of materials.
- 24 October 2024
- Published by Springer Nature in Research Square
Open AccessAnalysis of the plane stress state by combined ultrasonic waves
This study investigates the measurement of the residual stress state in ASTM A131 steel plates using a non-destructive technique based on the combination of ultrasonic waves. The method combines shear and compressive waves to more accurately assess the stress state of the material after heat application via TIG welding. Measurements were taken at different points on the plate using transducers attached to a stepper motor, which enabled the rotation of the transducer and precise determination of the wave propagation angle. The results showed that residual stresses were more concentrated near the weld zone and the supports that held the sample, while areas farther away showed significantly lower stresses. The technique proved effective in measuring the residual stress state, overcoming the limitations of traditional methods, which often estimate only the differences between principal stresses. This approach has the potential to be applied in various industries, particularly in sectors that require accurate stress evaluations in structural components, such as naval construction. The combined use of shear and compressive waves offers a non-destructive and highly precise alternative to ensure the integrity and durability of materials.
- Open Access
Morphological and Doping Effects on Electrical Conductivity of Aluminum Metal Substrate through Pulsed Electrodeposition Coating of Cu-MWCNT
The demand for more efficient and sustainable electrical systems has driven research in the quest for innovative materials that enhance the properties of electrical conductors. This study investigated the influence of copper (Cu) coating and multi-walled carbon nanotubes (MWCNTs) on aluminum metal substrate through the pulsed electrodeposition technique. Parameters such as the concentration of chemical elements, current, voltage, temperature, time, and electrode spacing were optimized in search of improving the nanocomposite coating. The metallic substrate underwent anodization as surface preparation for coating. Characterization techniques employed included Field Emission Gun—Scanning Electron Microscopy (FEG-SEM) for analyzing coating morphology, Energy-Dispersive X-Ray Spectroscopy (EDS), Raman spectroscopy, and Kelvin probe for obtaining surface electrical conductivity values. Homogeneous dispersion of the Cu-MWCNTs film coating was achieved across the entire surface of the aluminum plate, creating a complex morphology. The doping effect was highlighted by changes in the vibrational characteristics of the nanocomposite, which affected the Raman spectrum dispersion bands. An increase in surface electrical conductivity by ≈52.33% compared to the control sample was obtained. Therefore, these results indicate that the improvement in the material’s electrical properties is intrinsically related to the complex morphology achieved with the adopted Cu-MWCNT nanocomposite coating process.
Open AccessMorphological and Doping Effects on Electrical Conductivity of Aluminum Metal Substrate through Pulsed Electrodeposition Coating of Cu-MWCNT
The demand for more efficient and sustainable electrical systems has driven research in the quest for innovative materials that enhance the properties of electrical conductors. This study investigated the influence of copper (Cu) coating and multi-walled carbon nanotubes (MWCNTs) on aluminum metal substrate through the pulsed electrodeposition technique. Parameters such as the concentration of chemical elements, current, voltage, temperature, time, and electrode spacing were optimized in search of improving the nanocomposite coating. The metallic substrate underwent anodization as surface preparation for coating. Characterization techniques employed included Field Emission Gun—Scanning Electron Microscopy (FEG-SEM) for analyzing coating morphology, Energy-Dispersive X-Ray Spectroscopy (EDS), Raman spectroscopy, and Kelvin probe for obtaining surface electrical conductivity values. Homogeneous dispersion of the Cu-MWCNTs film coating was achieved across the entire surface of the aluminum plate, creating a complex morphology. The doping effect was highlighted by changes in the vibrational characteristics of the nanocomposite, which affected the Raman spectrum dispersion bands. An increase in surface electrical conductivity by ≈52.33% compared to the control sample was obtained. Therefore, these results indicate that the improvement in the material’s electrical properties is intrinsically related to the complex morphology achieved with the adopted Cu-MWCNT nanocomposite coating process.
- Open Access
- 23 June 2022
- Published by IntechOpen
A Brief Study of Unconventional Variants of GMAW Welding: Parameters, Weld Bead, and Microstructures
The GMAW (Gas Metal Arc Welding) process is an electric arc welding technique widely used around the world due to its ease of use, low equipment cost and, mainly, due to the high deposition rate, the quality of the metal of solder, which makes it versatile and susceptible to modification. Thus, variants such as CW-GMAW (Cold Wire–Gas Metal Arc Welding), DCW-GMAW (Double Cold Wire–Gas Metal Arc Welding), and HW-GMAW (Hot Wire–Gas Metal Arc Welding) emerged from the conception of small adaptations to the original process that ended up generating better and more adjusted results than GMAW. Thus, variations of some parameters will be shown and their respective effects on the weld bead geometry, dilution, penetration, deposition rate, in addition to the effects on macro and microstructure. This provides the possibility of using the variants in different types of applications in the industry in general. Where the application in narrow 4 mm chamfer has already been observed, reduction of residual stresses, increase in fatigue resistance and coatings with special alloys.
- 23 June 2022
- Published by IntechOpen
Open AccessA Brief Study of Unconventional Variants of GMAW Welding: Parameters, Weld Bead, and Microstructures
The GMAW (Gas Metal Arc Welding) process is an electric arc welding technique widely used around the world due to its ease of use, low equipment cost and, mainly, due to the high deposition rate, the quality of the metal of solder, which makes it versatile and susceptible to modification. Thus, variants such as CW-GMAW (Cold Wire–Gas Metal Arc Welding), DCW-GMAW (Double Cold Wire–Gas Metal Arc Welding), and HW-GMAW (Hot Wire–Gas Metal Arc Welding) emerged from the conception of small adaptations to the original process that ended up generating better and more adjusted results than GMAW. Thus, variations of some parameters will be shown and their respective effects on the weld bead geometry, dilution, penetration, deposition rate, in addition to the effects on macro and microstructure. This provides the possibility of using the variants in different types of applications in the industry in general. Where the application in narrow 4 mm chamfer has already been observed, reduction of residual stresses, increase in fatigue resistance and coatings with special alloys.
- Open Access
- 14 January 2021
- Published by IntechOpen
Welding Residual Stresses to the Electric Arc
Arc welding processes are widely used in the industrial sector, mainly for productivity and continuity. However, these processes have several undesirable results, such as distortions and residual stresses (RS). When compared to other welding processes, the RS level can make the welded joint unfeasible. Many studies on these arc welding discontinuities have been carried out in experimental and numerical areas about their measurement, analysis, and control, however, not yet clearly enlightened, since it is a complex topic, both for industry and academia, needing to be deepened. This study aims to present a contextualized approach to destructive and non-destructive techniques used to measure RS generated by arc welding, as well as the influence of these distortions and stresses on the welded structures and, finally, to present possible control techniques. Finally, this study highlights the use of CW-GMAW welding, which achieved a reduction in stress and distortion levels, due to the introduction of a non-energized wire in the arc of the GMAW process, as evidenced by the results of RS measured by X-ray diffraction (XRD) and acoustic birefringence (AB). Thus, in this context, the approach to RS in arc welding presented here is extremely relevant for researchers involved with the topic.
- 14 January 2021
- Published by IntechOpen
Open AccessWelding Residual Stresses to the Electric Arc
Arc welding processes are widely used in the industrial sector, mainly for productivity and continuity. However, these processes have several undesirable results, such as distortions and residual stresses (RS). When compared to other welding processes, the RS level can make the welded joint unfeasible. Many studies on these arc welding discontinuities have been carried out in experimental and numerical areas about their measurement, analysis, and control, however, not yet clearly enlightened, since it is a complex topic, both for industry and academia, needing to be deepened. This study aims to present a contextualized approach to destructive and non-destructive techniques used to measure RS generated by arc welding, as well as the influence of these distortions and stresses on the welded structures and, finally, to present possible control techniques. Finally, this study highlights the use of CW-GMAW welding, which achieved a reduction in stress and distortion levels, due to the introduction of a non-energized wire in the arc of the GMAW process, as evidenced by the results of RS measured by X-ray diffraction (XRD) and acoustic birefringence (AB). Thus, in this context, the approach to RS in arc welding presented here is extremely relevant for researchers involved with the topic.
- Open Access
- 1 January 2020
- Published by Brazilian Journal of Development in Brazilian Journal of Development
- Vol. 6 (5) , 26496-26516
Inverse problem for estimating and optimization of parameters of batch ethanol fermentation process using Bayesian techniques
Inverse problem for estimating and optimization of parameters of batch ethanol fermentation process using Bayesian techniques / Problema inverso para estimativa e otimização de parâmetros no processo de fermentação de etanol em reator batelada usando técnicas Bayesianas
- 1 January 2020
- Published by Brazilian Journal of Development in Brazilian Journal of Development
- Vol. 6 (5) , 26496-26516
Open AccessInverse problem for estimating and optimization of parameters of batch ethanol fermentation process using Bayesian techniques
Inverse problem for estimating and optimization of parameters of batch ethanol fermentation process using Bayesian techniques / Problema inverso para estimativa e otimização de parâmetros no processo de fermentação de etanol em reator batelada usando técnicas Bayesianas
- Open Access
Application of Cold Wire Gas Metal Arc Welding for Narrow Gap Welding (NGW) of High Strength Low Alloy Steel
Narrow gap welding is a prevalent technique used to decrease the volume of molten metal and heat required to fill a joint. Consequently, deleterious effects such as distortion and residual stresses may be reduced. One of the fields where narrow groove welding is most employed is pipeline welding where misalignment, productivity and mechanical properties are critical to a successful final assemblage of pipes. This work reports the feasibility of joining pipe sections with 4 mm-wide narrow gaps machined from API X80 linepipe using cold wire gas metal arc welding. Joints were manufactured using the standard gas metal arc welding and the cold wire gas metal arc welding processes, where high speed imaging, and voltage and current monitoring were used to study the arc dynamic features. Standard metallographic procedures were used to study sidewall penetration, and the evolution of the heat affected zone during welding. It was found that cold wire injection stabilizes the arc wandering, decreasing sidewall penetration while almost doubling deposition. However, this also decreases penetration, and incomplete penetration was found in the cold wire specimens as a drawback. However, adjusting the groove geometry or changing the welding parameters would resolve this penetration issue.
Open AccessApplication of Cold Wire Gas Metal Arc Welding for Narrow Gap Welding (NGW) of High Strength Low Alloy Steel
Narrow gap welding is a prevalent technique used to decrease the volume of molten metal and heat required to fill a joint. Consequently, deleterious effects such as distortion and residual stresses may be reduced. One of the fields where narrow groove welding is most employed is pipeline welding where misalignment, productivity and mechanical properties are critical to a successful final assemblage of pipes. This work reports the feasibility of joining pipe sections with 4 mm-wide narrow gaps machined from API X80 linepipe using cold wire gas metal arc welding. Joints were manufactured using the standard gas metal arc welding and the cold wire gas metal arc welding processes, where high speed imaging, and voltage and current monitoring were used to study the arc dynamic features. Standard metallographic procedures were used to study sidewall penetration, and the evolution of the heat affected zone during welding. It was found that cold wire injection stabilizes the arc wandering, decreasing sidewall penetration while almost doubling deposition. However, this also decreases penetration, and incomplete penetration was found in the cold wire specimens as a drawback. However, adjusting the groove geometry or changing the welding parameters would resolve this penetration issue.