Gurpreet Singh Kapur
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gurpreet Singh Kapur has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Priyanka Luthra
R&D Division, Indian Oil Corporation Ltd., Faridabad, Haryana, India
3 shared publicationsS. S. V. Ramakumar
R&D Division, Indian Oil Corporation Ltd., Faridabad, Haryana, India
3 shared publicationsVishal Goel
R&D Division, Indian Oil Corporation Ltd., Faridabad, Haryana, India
3 shared publications- Abhishek Sachan
Smart Plastics Group, IRDL CNRS 6027, University of South Brittany (UBS), 56321 Lorient, France
1 shared publication Gurmeet Singh
R&D Center, Indian Oil Corporation Limited, Faridabad-121007, India
1 shared publicationHemant Tyagi
Panipat Refinery, Indian Oil Corporation Ltd., Faridabad, Haryana, India
1 shared publication
Latest Publications
- 9 January 2022
- Published by Taylor & Francis in International Journal of Polymer Analysis and Characterization
- Vol. 27 (2) , 111-131
Time-domain NMR relaxometery – a green analytical tool for estimating physico-mechanical properties of polyolefins
Physical and mechanical properties of PE and PP are traditionally determined in the laboratory with methods as specified in ASTM/ISO standards. This is a time-consuming activity in any QC laboratory. In this paper, low-field (20 MHz) NMR has been used to quickly determine properties like density of HDPE, Xylene Solubles (XS) in homo-polymer PP & impact copolymer polypropylene (ICP), ethylene content (C2), flexural modulus (FM) and Izod impact strength of ICP, within a short span of time (∼1/4 h), allowing the plant to get expeditious feedback about the manufactured polymer grade enabling monitoring the manufacturing process more efficiently. The novelty in this work is that even calibration and predictive models for determining mechanical properties of polyolefins like FM and Izod impact strength have been successfully developed. Calibration models were built using known samples and validated using the validated sample set. For HDPE samples, a calibration model for determining the density could be prepared with R2 of 0.867 and RMSEC of 0.0006 gcm−3. For homo PP samples, a predictive model for determining XS could be prepared with R2 of 0.934 and RMSEC of 0.20 wt%. In case of calibration models for XS and C2 of ICP samples, R2 = 0.924 each and RMSEC of 0.54 wt% & 0.45 wt%, respectively was obtained. A model for flexural modulus could be prepared with an R2 and RMSEC of 0.935 & 28 MPa, respectively. Reasonable model could be developed for Izod impact strength (R2 = 0.947 & 0.982 for low & high impact respectively). The properties of validation sample set were predicted based on the calibration models and good correlation was obtained between the lab data (QC data) and the predicted data.
- 9 January 2022
- Published by Taylor & Francis in International Journal of Polymer Analysis and Characterization
- Vol. 27 (2) , 111-131
Time-domain NMR relaxometery – a green analytical tool for estimating physico-mechanical properties of polyolefins
Physical and mechanical properties of PE and PP are traditionally determined in the laboratory with methods as specified in ASTM/ISO standards. This is a time-consuming activity in any QC laboratory. In this paper, low-field (20 MHz) NMR has been used to quickly determine properties like density of HDPE, Xylene Solubles (XS) in homo-polymer PP & impact copolymer polypropylene (ICP), ethylene content (C2), flexural modulus (FM) and Izod impact strength of ICP, within a short span of time (∼1/4 h), allowing the plant to get expeditious feedback about the manufactured polymer grade enabling monitoring the manufacturing process more efficiently. The novelty in this work is that even calibration and predictive models for determining mechanical properties of polyolefins like FM and Izod impact strength have been successfully developed. Calibration models were built using known samples and validated using the validated sample set. For HDPE samples, a calibration model for determining the density could be prepared with R2 of 0.867 and RMSEC of 0.0006 gcm−3. For homo PP samples, a predictive model for determining XS could be prepared with R2 of 0.934 and RMSEC of 0.20 wt%. In case of calibration models for XS and C2 of ICP samples, R2 = 0.924 each and RMSEC of 0.54 wt% & 0.45 wt%, respectively was obtained. A model for flexural modulus could be prepared with an R2 and RMSEC of 0.935 & 28 MPa, respectively. Reasonable model could be developed for Izod impact strength (R2 = 0.947 & 0.982 for low & high impact respectively). The properties of validation sample set were predicted based on the calibration models and good correlation was obtained between the lab data (QC data) and the predicted data.
- 6 March 2021
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 29 (10) , 3079-3104
Biodegradable/Bio-plastics: Myths and Realities
- 6 March 2021
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 29 (10) , 3079-3104
Biodegradable/Bio-plastics: Myths and Realities
- Open Access
- 12 May 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (31) , 18180-18191
Recent advances in catalytic chain transfer polymerization of isobutylene: a review
This review presents the development of highly reactive polyisobutylene (HRPIB), a major commercial intermediate toward fuel and lubricant additives. Recent years have witnessed very substantial advances in the catalytic chain transfer polymerization (CCTP) of isobutylene/industrial Raffinate-1 (C4 Raffinate) to produce HRPIB, particularly in nonpolar solvents at elevated temperatures. The main subjects of this review are cationic polymerization of isobutylene, progress in HRPIB research and existing challenges, and recent advances of CCTP. New initiating/catalyst systems based on ionic liquids with Lewis acids are detailed, and this approach may open new views in the synthesis of HRPIB. Some current developments in CCTP of industrial Raffinate-1 and mechanistic studies are also described. This review strongly supports that the hydrocarbon soluble Lewis acid·ether (LA·ether) complex catalyzed CCTP will become the most popular technique for preparing HRPIB and could replace the traditional BF3 catalyzed industrial method.
- 12 May 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (31) , 18180-18191
Open AccessRecent advances in catalytic chain transfer polymerization of isobutylene: a review
This review presents the development of highly reactive polyisobutylene (HRPIB), a major commercial intermediate toward fuel and lubricant additives. Recent years have witnessed very substantial advances in the catalytic chain transfer polymerization (CCTP) of isobutylene/industrial Raffinate-1 (C4 Raffinate) to produce HRPIB, particularly in nonpolar solvents at elevated temperatures. The main subjects of this review are cationic polymerization of isobutylene, progress in HRPIB research and existing challenges, and recent advances of CCTP. New initiating/catalyst systems based on ionic liquids with Lewis acids are detailed, and this approach may open new views in the synthesis of HRPIB. Some current developments in CCTP of industrial Raffinate-1 and mechanistic studies are also described. This review strongly supports that the hydrocarbon soluble Lewis acid·ether (LA·ether) complex catalyzed CCTP will become the most popular technique for preparing HRPIB and could replace the traditional BF3 catalyzed industrial method.
- 28 February 2020
- Published by Springer Nature in SN Applied Sciences
- Vol. 2 (3) , 1-13
Biodegradation studies of polypropylene/natural fiber composites
- 28 February 2020
- Published by Springer Nature in SN Applied Sciences
- Vol. 2 (3) , 1-13
Biodegradation studies of polypropylene/natural fiber composites
- 23 May 2017
- Published by Wiley in Polymer Composites
- Vol. 39 (S1)
Chemical treatment of cotton stalk and its effects on mechanical, rheological and morphological properties of Polypropylene/cotton stalk bio‐composites
Cotton stalk as commercially viable bio fiber for preparing bio‐composites is explored of late, and the effects of various chemical treatments of cotton stalk fiber on mechanical, rheological and morphological properties of Polypropylene (PP)‐Cotton stalk (CS) bio‐composites are reported in this study. PP‐CS bio‐composites were prepared by varying the amount of cotton stalk from 10 to 50% by melt mixing in twin screw extruder and then injection molded to make specimen. PP‐CS bio‐composites with 50 wt% untreated CS were found to have maximum improvement in tensile modulus (83%), flexural modulus (120%), impact strength (39%). Similar to tensile and flexural modulus, the storage modulus of the PP‐CS composites was also increased with incorporation of CS into the PP matrix. To further increase the interaction between CS and PP matrix, four different chemical treatments (alkali, silane, permanganate solution and stearic acid) were tested for mechanical properties of CS‐PP bio‐composites. Among them KMnO4 treatment was found most effective on overall enhancement of bio‐composite properties. Chemically treated CS‐PP bio‐composites could be an economic viable option to prepare high quality low cost composites for suitable applications in various interior parts of automotives and house hold products. POLYM. COMPOS., 39:E286–E296, 2018. © 2017 Society of Plastics Engineers
- 23 May 2017
- Published by Wiley in Polymer Composites
- Vol. 39 (S1)
Chemical treatment of cotton stalk and its effects on mechanical, rheological and morphological properties of Polypropylene/cotton stalk bio‐composites
Cotton stalk as commercially viable bio fiber for preparing bio‐composites is explored of late, and the effects of various chemical treatments of cotton stalk fiber on mechanical, rheological and morphological properties of Polypropylene (PP)‐Cotton stalk (CS) bio‐composites are reported in this study. PP‐CS bio‐composites were prepared by varying the amount of cotton stalk from 10 to 50% by melt mixing in twin screw extruder and then injection molded to make specimen. PP‐CS bio‐composites with 50 wt% untreated CS were found to have maximum improvement in tensile modulus (83%), flexural modulus (120%), impact strength (39%). Similar to tensile and flexural modulus, the storage modulus of the PP‐CS composites was also increased with incorporation of CS into the PP matrix. To further increase the interaction between CS and PP matrix, four different chemical treatments (alkali, silane, permanganate solution and stearic acid) were tested for mechanical properties of CS‐PP bio‐composites. Among them KMnO4 treatment was found most effective on overall enhancement of bio‐composite properties. Chemically treated CS‐PP bio‐composites could be an economic viable option to prepare high quality low cost composites for suitable applications in various interior parts of automotives and house hold products. POLYM. COMPOS., 39:E286–E296, 2018. © 2017 Society of Plastics Engineers
- Open Access
- 29 January 2014
- Published by Hindawi Limited in Journal of Fuels
- Vol. 2014, 1-8
Compatibility Studies on Elastomers and Polymers with Ethanol Blended Gasoline
This paper reports the compatibility studies of 10% ethanol blended gasoline (E10) with four types of elastomer materials, namely, Neoprene rubber, Nitrile rubber, hydrogenated Nitrile butadiene rubber (HNBR), and Polyvinyl chloride/Nitrile butadiene rubber blend (PVC/NBR), and two types of plastic materials, namely, Nylon-66 and Polyoxymethylene (Delrin). These materials have applications in automotives as engine seals, gaskets, fuel system seals and hoses, and so forth. Two types of the ethanol blended gasoline mixtures were used: (a) gasoline containing 5% ethanol (E5), which is commercial form of gasoline available in India, and (b) gasoline containing 10% ethanol (E10). The above materials were immersed in E5 and E10 for 500 hrs at 55°C. A set of eight different properties in E5 and E10 (visual inspection, weight change, volume change, tensile strength, percent elongation, flexural strength, impact strength, and hardness) were measured after completion of 500 hrs and compared with reference specimens (specimens at 55°C without fuel and specimens at ambient conditions). Variation observed in different materials with respect to the above eight properties has been used to draw inference about the compatibility of these elastomeric/polymer materials with E10 fuel vis-à-vis E5 fuels. The data presented in this study is comparative in nature between the results of E10 and E5.
- 29 January 2014
- Published by Hindawi Limited in Journal of Fuels
- Vol. 2014, 1-8
Open AccessCompatibility Studies on Elastomers and Polymers with Ethanol Blended Gasoline
This paper reports the compatibility studies of 10% ethanol blended gasoline (E10) with four types of elastomer materials, namely, Neoprene rubber, Nitrile rubber, hydrogenated Nitrile butadiene rubber (HNBR), and Polyvinyl chloride/Nitrile butadiene rubber blend (PVC/NBR), and two types of plastic materials, namely, Nylon-66 and Polyoxymethylene (Delrin). These materials have applications in automotives as engine seals, gaskets, fuel system seals and hoses, and so forth. Two types of the ethanol blended gasoline mixtures were used: (a) gasoline containing 5% ethanol (E5), which is commercial form of gasoline available in India, and (b) gasoline containing 10% ethanol (E10). The above materials were immersed in E5 and E10 for 500 hrs at 55°C. A set of eight different properties in E5 and E10 (visual inspection, weight change, volume change, tensile strength, percent elongation, flexural strength, impact strength, and hardness) were measured after completion of 500 hrs and compared with reference specimens (specimens at 55°C without fuel and specimens at ambient conditions). Variation observed in different materials with respect to the above eight properties has been used to draw inference about the compatibility of these elastomeric/polymer materials with E10 fuel vis-à-vis E5 fuels. The data presented in this study is comparative in nature between the results of E10 and E5.
- 17 October 2013
- Published by Wiley in Polymer Composites
- Vol. 35 (4) , 708-714
Mechanical properties of modified biofiller‐polypropylene composites
This article reports the mechanical, thermal, and morphological properties of polypropylene (PP)‐chicken eggshell (ES) composites. Mechanical properties like tensile strength, tensile modulus, izod impact strength, flexural modulus of PP composites with normal (unmodified) eggshell and chemically treated ES [modified ES (MES) with isophthalic acid] have been investigated. PP–calcium carbonate (CaCO3) composites, at the same filler loadings, were also prepared and used as reference. The results showed that PP composites with chemically MES had better mechanical properties compared to the unmodified ES and CaCO3 composites. An increase of about 3–18% in tensile modulus, 4–44% in izod impact strength and 1.5–26% in flexural modulus at different filler loading was observed in MES composites as compared to unmodified ES composites. Scanning electron microscopy (SEM) micrographs of fractured tensile specimens confirmed better interfacial adhesion of MES with polymer matrix resulting into lower voids and plastic deformation resulting in improved mechanicals of the composites. TEM micrographs showed acicular needle shaped morphology for modified ES and have contributed to better dispersion which is the prime reason for enhancement of all the mechanical properties. At higher filler loading, the modulus of MES composite was found to be higher by 5% as compared to commercial CaCO3 composites. POLYM. COMPOS., 35:708–714, 2014. © 2013 Society of Plastics Engineers
- 17 October 2013
- Published by Wiley in Polymer Composites
- Vol. 35 (4) , 708-714
Mechanical properties of modified biofiller‐polypropylene composites
This article reports the mechanical, thermal, and morphological properties of polypropylene (PP)‐chicken eggshell (ES) composites. Mechanical properties like tensile strength, tensile modulus, izod impact strength, flexural modulus of PP composites with normal (unmodified) eggshell and chemically treated ES [modified ES (MES) with isophthalic acid] have been investigated. PP–calcium carbonate (CaCO3) composites, at the same filler loadings, were also prepared and used as reference. The results showed that PP composites with chemically MES had better mechanical properties compared to the unmodified ES and CaCO3 composites. An increase of about 3–18% in tensile modulus, 4–44% in izod impact strength and 1.5–26% in flexural modulus at different filler loading was observed in MES composites as compared to unmodified ES composites. Scanning electron microscopy (SEM) micrographs of fractured tensile specimens confirmed better interfacial adhesion of MES with polymer matrix resulting into lower voids and plastic deformation resulting in improved mechanicals of the composites. TEM micrographs showed acicular needle shaped morphology for modified ES and have contributed to better dispersion which is the prime reason for enhancement of all the mechanical properties. At higher filler loading, the modulus of MES composite was found to be higher by 5% as compared to commercial CaCO3 composites. POLYM. COMPOS., 35:708–714, 2014. © 2013 Society of Plastics Engineers