Nazeer Ahmad Anjum
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nazeer Ahmad Anjum has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Shahid Mehmood
Department of Mechanical Engineering, University of Engineering and Technology Taxila, Taxila 47050, Pakistan
2 shared publications - Waqas Anwar
National Engineering and Scientific Commission of Pakistan
2 shared publications - Amir Sultan
Department of Mechatronics Engineering, University of Engineering and Technology Taxila
1 shared publication - F. Qayyum
Fracture Mechanics and Fatigue Laboratory, Mechanical Engineering Department, University of Engineering and Technology, Taxila, Pakistan
1 shared publication K. Javed
University of Engineering and Technology (UET), Taxila
1 shared publication- Masood Shah
University of Engineering and Technology
1 shared publication
Latest Publications
- Open Access
- 1 April 2019
- Published by Mehran University of Engineering and Technology in Mehran University Research Journal of Engineering and Technology
- Vol. 38 (2) , 435-442
Augmentation of Fatigue and Tensile Strength of AA-6061 Processed through Equal Channel Angular Pressing
ECAP (Equal Channel Angular Pressing) is a technique used to enhance the strength of material by grain refinement. In this research, an aerospace grade aluminum alloy-6061 is investigated. The specimens were pressed through ECAP die channels, intersecting each other at an angle of 90oC where a shear plane of 45oC was developed, that results grains refinement. Fatigue strengths and CGR (Crack Growth Rate) for the stress ratio R 0.7 and 0.1 are found and compared with the as-received material.It was observed that the CGR is slower at stress ratio R=0.1, as compared to stress ration R=0.7. An electric furnace was embedded with ECAP die to regulate the material flow through this die. The temperature of the die was maintained at 450oC during ECAP pressing and the specimens were also preheated at this temperature using another furnace. The ECAP die consistsof two channels intersecting at 90o provided with safe inner and outer corner radius to avoid scaling.The microstructural observations revealed that the deformation was perfectly plastic. The ECAPed and as-received materials were also characterized by tensile tests, micro-hardness tests, and 3-point bend fatigue tests.
- 1 April 2019
- Published by Mehran University of Engineering and Technology in Mehran University Research Journal of Engineering and Technology
- Vol. 38 (2) , 435-442
Open AccessAugmentation of Fatigue and Tensile Strength of AA-6061 Processed through Equal Channel Angular Pressing
ECAP (Equal Channel Angular Pressing) is a technique used to enhance the strength of material by grain refinement. In this research, an aerospace grade aluminum alloy-6061 is investigated. The specimens were pressed through ECAP die channels, intersecting each other at an angle of 90oC where a shear plane of 45oC was developed, that results grains refinement. Fatigue strengths and CGR (Crack Growth Rate) for the stress ratio R 0.7 and 0.1 are found and compared with the as-received material.It was observed that the CGR is slower at stress ratio R=0.1, as compared to stress ration R=0.7. An electric furnace was embedded with ECAP die to regulate the material flow through this die. The temperature of the die was maintained at 450oC during ECAP pressing and the specimens were also preheated at this temperature using another furnace. The ECAP die consistsof two channels intersecting at 90o provided with safe inner and outer corner radius to avoid scaling.The microstructural observations revealed that the deformation was perfectly plastic. The ECAPed and as-received materials were also characterized by tensile tests, micro-hardness tests, and 3-point bend fatigue tests.
- Open Access
- 4 April 2018
- Published by Pakistan Atomic Energy Commission in The Nucleus
- Vol. 55 (1) , 38-46
A Review of the Effect of Electric Discharge Machining on the Surface Integrity of Metallic Parts
In Electric Discharge Machining (EDM), after each electric discharge, a small portion of the molten pool is removed and the residue re-solidifies on the surface in the form of layer. This re-solidified layer has different microstructure and metallurgical properties than the parent material. Many investigations have been carried out on EDM of different materials to evaluate the influence of electrical parameters, dielectric type, electrode material and discharge gap on the Material Removal Rate (MRR), tool wear rate and surface integrity (surface roughness, cracks, residual stresses and white layer formation). Voltage, pulse current, pulse on-time, pulse off-time and polarity are electric parameters that control discharge energy as well as heating and cooling times. It has been observed that high discharge energy gives high surface roughness, high MRR and high residual stresses. A detailed literature review comprising effects of different parameters on surface conditions like metallurgical characteristics, surface roughness, surface hardness and distribution of residual stresses, is presented here
- 4 April 2018
- Published by Pakistan Atomic Energy Commission in The Nucleus
- Vol. 55 (1) , 38-46
Open AccessA Review of the Effect of Electric Discharge Machining on the Surface Integrity of Metallic Parts
In Electric Discharge Machining (EDM), after each electric discharge, a small portion of the molten pool is removed and the residue re-solidifies on the surface in the form of layer. This re-solidified layer has different microstructure and metallurgical properties than the parent material. Many investigations have been carried out on EDM of different materials to evaluate the influence of electrical parameters, dielectric type, electrode material and discharge gap on the Material Removal Rate (MRR), tool wear rate and surface integrity (surface roughness, cracks, residual stresses and white layer formation). Voltage, pulse current, pulse on-time, pulse off-time and polarity are electric parameters that control discharge energy as well as heating and cooling times. It has been observed that high discharge energy gives high surface roughness, high MRR and high residual stresses. A detailed literature review comprising effects of different parameters on surface conditions like metallurgical characteristics, surface roughness, surface hardness and distribution of residual stresses, is presented here
- Open Access
- 1 March 2017
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 11 (1) , 29-35
DETERMINATION OF RESIDUAL STRESS DISTRIBUTION IN HIGH STRENGTH ALUMINUM ALLOY AFTER EDM
Thermal energy produced by discrete and random electric sparks in electric discharge machining (EDM) melts surface material. A portion of this molten material is removed and the remaining material resolidified by rapid cooling in a hydrocarbon oil. The effect of repeated heating and cooling of...
- 1 March 2017
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 11 (1) , 29-35
Open AccessDETERMINATION OF RESIDUAL STRESS DISTRIBUTION IN HIGH STRENGTH ALUMINUM ALLOY AFTER EDM
Thermal energy produced by discrete and random electric sparks in electric discharge machining (EDM) melts surface material. A portion of this molten material is removed and the remaining material resolidified by rapid cooling in a hydrocarbon oil. The effect of repeated heating and cooling of...
- Open Access
- 13 December 2015
- Published by Pakistan Atomic Energy Commission in The Nucleus
- Vol. 52 (4) , 169-175
Shear Strain Model for Equal Channel Angular Pressing in High Elastic Extruded Plastics
This paper presents a novel model for plastic shear strain calculation in the Equal Channel Angular Pressing (ECAP). The model is particularly formulated to furnish for the elastic recovery after extrusion. Due to high elastic recovery after plastic deformation in polymers, the behavior of Teflon and Nylon is investigated at different temperatures as they are famous for their low coefficient of friction and wall friction effects. The main concentration is given to the basic principle of ECAP processing parameters such as strain, slip bands, and shearing patterns. In this research, a new engraved circle marking technique is used to trace the plastic deformation in the specimens. Afterwards, image analysis approach is applied to measure the deformation, strain and rotation after extrusion. The experimental results are validated with the ABAQUS based numerical simulation. A close conformity is found between them.
- 13 December 2015
- Published by Pakistan Atomic Energy Commission in The Nucleus
- Vol. 52 (4) , 169-175
Open AccessShear Strain Model for Equal Channel Angular Pressing in High Elastic Extruded Plastics
This paper presents a novel model for plastic shear strain calculation in the Equal Channel Angular Pressing (ECAP). The model is particularly formulated to furnish for the elastic recovery after extrusion. Due to high elastic recovery after plastic deformation in polymers, the behavior of Teflon and Nylon is investigated at different temperatures as they are famous for their low coefficient of friction and wall friction effects. The main concentration is given to the basic principle of ECAP processing parameters such as strain, slip bands, and shearing patterns. In this research, a new engraved circle marking technique is used to trace the plastic deformation in the specimens. Afterwards, image analysis approach is applied to measure the deformation, strain and rotation after extrusion. The experimental results are validated with the ABAQUS based numerical simulation. A close conformity is found between them.