Waqas Anwar
Research Subjects
Waqas Anwar has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Nazeer Ahmad Anjum
Department of Mechanical Engineering, University of Engineering & Technology, Taxila, Pakistan
2 shared publications - F. Qayyum
Fracture Mechanics and Fatigue Laboratory, Mechanical Engineering Department, University of Engineering and Technology, Taxila, Pakistan
1 shared publication - Masood Shah
University of Engineering and Technology
1 shared publication - Muhammad Shahid Khalil
Department of Mechanical Engineering, University of Engineering and Technology, Taxila 47080, Pakistan
1 shared publication - Muhammad Zubair Khan
Institute of Space Technology Department of Mechanical Engineering 1 Islamabad Expressway, Islamabad 44000 , Pakistan
1 shared publication - R. A. Pasha
University of Engineering and Technology, Taxila, Pakistan
1 shared publication
Latest Publications
- Open Access
- 1 April 2019
- Published by Mehran University of Engineering and Technology in Mehran University Research Journal of Engineering and Technology
- Vol. 38 (2) , 435-442
Augmentation of Fatigue and Tensile Strength of AA-6061 Processed through Equal Channel Angular Pressing
ECAP (Equal Channel Angular Pressing) is a technique used to enhance the strength of material by grain refinement. In this research, an aerospace grade aluminum alloy-6061 is investigated. The specimens were pressed through ECAP die channels, intersecting each other at an angle of 90oC where a shear plane of 45oC was developed, that results grains refinement. Fatigue strengths and CGR (Crack Growth Rate) for the stress ratio R 0.7 and 0.1 are found and compared with the as-received material.It was observed that the CGR is slower at stress ratio R=0.1, as compared to stress ration R=0.7. An electric furnace was embedded with ECAP die to regulate the material flow through this die. The temperature of the die was maintained at 450oC during ECAP pressing and the specimens were also preheated at this temperature using another furnace. The ECAP die consistsof two channels intersecting at 90o provided with safe inner and outer corner radius to avoid scaling.The microstructural observations revealed that the deformation was perfectly plastic. The ECAPed and as-received materials were also characterized by tensile tests, micro-hardness tests, and 3-point bend fatigue tests.
- 1 April 2019
- Published by Mehran University of Engineering and Technology in Mehran University Research Journal of Engineering and Technology
- Vol. 38 (2) , 435-442
Open AccessAugmentation of Fatigue and Tensile Strength of AA-6061 Processed through Equal Channel Angular Pressing
ECAP (Equal Channel Angular Pressing) is a technique used to enhance the strength of material by grain refinement. In this research, an aerospace grade aluminum alloy-6061 is investigated. The specimens were pressed through ECAP die channels, intersecting each other at an angle of 90oC where a shear plane of 45oC was developed, that results grains refinement. Fatigue strengths and CGR (Crack Growth Rate) for the stress ratio R 0.7 and 0.1 are found and compared with the as-received material.It was observed that the CGR is slower at stress ratio R=0.1, as compared to stress ration R=0.7. An electric furnace was embedded with ECAP die to regulate the material flow through this die. The temperature of the die was maintained at 450oC during ECAP pressing and the specimens were also preheated at this temperature using another furnace. The ECAP die consistsof two channels intersecting at 90o provided with safe inner and outer corner radius to avoid scaling.The microstructural observations revealed that the deformation was perfectly plastic. The ECAPed and as-received materials were also characterized by tensile tests, micro-hardness tests, and 3-point bend fatigue tests.
- Open Access
- 13 December 2015
- Published by Pakistan Atomic Energy Commission in The Nucleus
- Vol. 52 (4) , 169-175
Shear Strain Model for Equal Channel Angular Pressing in High Elastic Extruded Plastics
This paper presents a novel model for plastic shear strain calculation in the Equal Channel Angular Pressing (ECAP). The model is particularly formulated to furnish for the elastic recovery after extrusion. Due to high elastic recovery after plastic deformation in polymers, the behavior of Teflon and Nylon is investigated at different temperatures as they are famous for their low coefficient of friction and wall friction effects. The main concentration is given to the basic principle of ECAP processing parameters such as strain, slip bands, and shearing patterns. In this research, a new engraved circle marking technique is used to trace the plastic deformation in the specimens. Afterwards, image analysis approach is applied to measure the deformation, strain and rotation after extrusion. The experimental results are validated with the ABAQUS based numerical simulation. A close conformity is found between them.
- 13 December 2015
- Published by Pakistan Atomic Energy Commission in The Nucleus
- Vol. 52 (4) , 169-175
Open AccessShear Strain Model for Equal Channel Angular Pressing in High Elastic Extruded Plastics
This paper presents a novel model for plastic shear strain calculation in the Equal Channel Angular Pressing (ECAP). The model is particularly formulated to furnish for the elastic recovery after extrusion. Due to high elastic recovery after plastic deformation in polymers, the behavior of Teflon and Nylon is investigated at different temperatures as they are famous for their low coefficient of friction and wall friction effects. The main concentration is given to the basic principle of ECAP processing parameters such as strain, slip bands, and shearing patterns. In this research, a new engraved circle marking technique is used to trace the plastic deformation in the specimens. Afterwards, image analysis approach is applied to measure the deformation, strain and rotation after extrusion. The experimental results are validated with the ABAQUS based numerical simulation. A close conformity is found between them.