Zhao Yin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zhao Yin has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
Yujie Xu
6 shared publications- Haisheng Chen
Institute of Engineering Thermophysics, Chinese Academy of Sciences
5 shared publications - Hualiang Zhang
Institute of Engineering Thermophysics
4 shared publications Yu Liu
4 shared publicationsHualiang Zhang
Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing, China
3 shared publications- Tao Wang3 shared publications
Latest Publications
- Open Access
- 24 October 2026
- Published by Elsevier in SSRN Electronic Journal
Optimal design of an aircraft-skin-integrated micro-pin-fin condenser for the water-enhanced turbofan
The water-enhanced turbofan (WET) is an emerging engine concept with the potential to substantially reduce fuel consumption and emissions. Its condenser is a key component that enables water condensation by cooling the core exhaust to induce condensation. Existing designs are constrained by small heat-transfer temperature differences, high mass and large pressure losses, limiting WET development. This study proposes a novel aircraft-skin-integrated micro-pin-fin condenser, with pin fins and hot-side passages located on the inner side of the aircraft skin. The configuration uses the high-speed freestream at cruise altitude to cool exhaust through the skin. Models for heat transfer and hot-side pressure loss are developed and validated against three-dimensional CFD simulations and experimental data. Aircraft transport efficiency is adopted as the ultimate design objective to balance condenser mass and hot-side pressure loss. Multi-objective optimization uses the elitist non-dominated sorting genetic algorithm II (NSGA-II). Three-dimensional simulations provide the air-side convective heat-transfer coefficient distribution over the aircraft skin. A simplified design adopts identical condenser units and neglects spatial non-uniformity in this coefficient. A subsequent zonal design divides the installation into six regions according to local air-side heat-transfer coefficients and optimizes the unit geometry and zonal flow allocation. The design result achieves a relative water condensation rate of 100.0%. The selected condenser attains a heat flux of 8.044 kW/m² and a heat transfer per unit mass of 13.683 kW/kg, with a maximum hot-side pressure-loss ratio of 1.708% and a total condenser of 302.154 kg per engine.
- 24 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessOptimal design of an aircraft-skin-integrated micro-pin-fin condenser for the water-enhanced turbofan
The water-enhanced turbofan (WET) is an emerging engine concept with the potential to substantially reduce fuel consumption and emissions. Its condenser is a key component that enables water condensation by cooling the core exhaust to induce condensation. Existing designs are constrained by small heat-transfer temperature differences, high mass and large pressure losses, limiting WET development. This study proposes a novel aircraft-skin-integrated micro-pin-fin condenser, with pin fins and hot-side passages located on the inner side of the aircraft skin. The configuration uses the high-speed freestream at cruise altitude to cool exhaust through the skin. Models for heat transfer and hot-side pressure loss are developed and validated against three-dimensional CFD simulations and experimental data. Aircraft transport efficiency is adopted as the ultimate design objective to balance condenser mass and hot-side pressure loss. Multi-objective optimization uses the elitist non-dominated sorting genetic algorithm II (NSGA-II). Three-dimensional simulations provide the air-side convective heat-transfer coefficient distribution over the aircraft skin. A simplified design adopts identical condenser units and neglects spatial non-uniformity in this coefficient. A subsequent zonal design divides the installation into six regions according to local air-side heat-transfer coefficients and optimizes the unit geometry and zonal flow allocation. The design result achieves a relative water condensation rate of 100.0%. The selected condenser attains a heat flux of 8.044 kW/m² and a heat transfer per unit mass of 13.683 kW/kg, with a maximum hot-side pressure-loss ratio of 1.708% and a total condenser of 302.154 kg per engine.
- Open Access
- 11 October 2026
- Published by Elsevier in SSRN Electronic Journal
Optimization Design of an Exhaust-Duct-Integrated Helical-Coil Steam Generator
Water-enhanced turbofan (WET) engines have attracted increasing attention as a promising route for reducing fuel consumption and emissions. The steam generator is a key component of the WET, where exhaust waste heat is recovered to generate high-temperature and high-pressure steam. Its design must simultaneously improve compactness and reduce flow losses, heat-transfer temperature difference, and structural mass, which remains a critical challenge for WET engine implementation. In this study, an exhaust-duct-integrated helical-coil steam generator (EDI-HCSG) is proposed, and a one-dimensional thermal-hydraulic model is developed for its performance predictions and optimized designs. The model is validated by publicly available steam-generator data and CFD results, with errors in heat duty and outlet temperature within ±2.3% and ±3.91%, respectively. Based on the validated model, response surface methodology (RSM) and NSGA-II are combined to quantify the trade-off between steam-generator mass and hot-side flow loss under heat-duty and total-pressure-recovery constraints. The final design is selected from the Pareto front by further considering aircraft transport efficiency. The average heat-transfer temperature difference is 52.93 K, indicating relatively low heat-transfer irreversibility during exhaust heat recovery. The optimized EDI-HCSG achieves hot- and cold-side total pressure recovery coefficients of 0.91 and 0.931, respectively, and a mass-specific heat duty of 18.05 kW/kg. Compared with representative steam-generator designs from various application fields, the proposed EDI-HCSG demonstrates favorable performance in terms of compactness, mass-specific heat-transfer capacity, and other key metrics. These results indicate that the EDI-HCSG provides a feasible lightweight steam-generator configuration for WET engine exhaust heat recovery.
- 11 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessOptimization Design of an Exhaust-Duct-Integrated Helical-Coil Steam Generator
Water-enhanced turbofan (WET) engines have attracted increasing attention as a promising route for reducing fuel consumption and emissions. The steam generator is a key component of the WET, where exhaust waste heat is recovered to generate high-temperature and high-pressure steam. Its design must simultaneously improve compactness and reduce flow losses, heat-transfer temperature difference, and structural mass, which remains a critical challenge for WET engine implementation. In this study, an exhaust-duct-integrated helical-coil steam generator (EDI-HCSG) is proposed, and a one-dimensional thermal-hydraulic model is developed for its performance predictions and optimized designs. The model is validated by publicly available steam-generator data and CFD results, with errors in heat duty and outlet temperature within ±2.3% and ±3.91%, respectively. Based on the validated model, response surface methodology (RSM) and NSGA-II are combined to quantify the trade-off between steam-generator mass and hot-side flow loss under heat-duty and total-pressure-recovery constraints. The final design is selected from the Pareto front by further considering aircraft transport efficiency. The average heat-transfer temperature difference is 52.93 K, indicating relatively low heat-transfer irreversibility during exhaust heat recovery. The optimized EDI-HCSG achieves hot- and cold-side total pressure recovery coefficients of 0.91 and 0.931, respectively, and a mass-specific heat duty of 18.05 kW/kg. Compared with representative steam-generator designs from various application fields, the proposed EDI-HCSG demonstrates favorable performance in terms of compactness, mass-specific heat-transfer capacity, and other key metrics. These results indicate that the EDI-HCSG provides a feasible lightweight steam-generator configuration for WET engine exhaust heat recovery.
- 20 July 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 179
Thermodynamic performance and exergy destruction of an NH3-fueled SOFC-GT system for green energy applications
- 20 July 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 179
Thermodynamic performance and exergy destruction of an NH3-fueled SOFC-GT system for green energy applications
- Open Access
- 14 May 2026
- Published by Elsevier in SSRN Electronic Journal
Thermodynamic Performance and Exergy Destruction of an NH3-Fueled SOFC-GT System for Green Energy Applications
The combined solid oxide fuel cell and gas turbine (SOFC-GT) system is gaining recognition as a highly efficient energy conversion solution, known for its superior electrical performance, minimal emissions, and versatile fuel compatibility. Ammonia is considered a zero-carbon energy carrier with relatively low storage and transportation costs, and it demonstrates strong potential for use in green aerospace energy systems. This study examines an NH3-SOFC-GT system, using the corresponding CH4- and H2-fueled configurations as reference cases. Under the same power output condition, the thermodynamic performance and parametric characteristics of the three systems are analyzed. An advanced exergy-based method is further applied to characterize the distribution of irreversibilities and to assess the performance enhancement potential of system components under different fuel conditions. Based on the above analysis, an improved configuration of the NH3-SOFC-GT system is developed and benchmarked against the original one. It is found that the ammonia-based system achieves an electrical efficiency 4.14 percentage points higher than the methane-based system, while remaining comparable to the hydrogen-based system. In addition, increasing the fuel utilization factor and compressor pressure ratio contributes to the improvement of system efficiency. An advanced exergy-based evaluation indicates that compressors, inverter, and turbine exhibit considerable improvement potential in all three systems. Endogenous contributions dominate the exergy losses of most components, whereas the SOFC shows a predominance of exogenous effects in both the NH3- and H2-fueled systems, indicating that coordinated improvement among components is required. Furthermore, the reconfigured system achieves 2.18 percentage point increase in electrical efficiency, while simultaneously lowering total irreversibility and improving the improvement potential of key components.
- 14 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessThermodynamic Performance and Exergy Destruction of an NH3-Fueled SOFC-GT System for Green Energy Applications
The combined solid oxide fuel cell and gas turbine (SOFC-GT) system is gaining recognition as a highly efficient energy conversion solution, known for its superior electrical performance, minimal emissions, and versatile fuel compatibility. Ammonia is considered a zero-carbon energy carrier with relatively low storage and transportation costs, and it demonstrates strong potential for use in green aerospace energy systems. This study examines an NH3-SOFC-GT system, using the corresponding CH4- and H2-fueled configurations as reference cases. Under the same power output condition, the thermodynamic performance and parametric characteristics of the three systems are analyzed. An advanced exergy-based method is further applied to characterize the distribution of irreversibilities and to assess the performance enhancement potential of system components under different fuel conditions. Based on the above analysis, an improved configuration of the NH3-SOFC-GT system is developed and benchmarked against the original one. It is found that the ammonia-based system achieves an electrical efficiency 4.14 percentage points higher than the methane-based system, while remaining comparable to the hydrogen-based system. In addition, increasing the fuel utilization factor and compressor pressure ratio contributes to the improvement of system efficiency. An advanced exergy-based evaluation indicates that compressors, inverter, and turbine exhibit considerable improvement potential in all three systems. Endogenous contributions dominate the exergy losses of most components, whereas the SOFC shows a predominance of exogenous effects in both the NH3- and H2-fueled systems, indicating that coordinated improvement among components is required. Furthermore, the reconfigured system achieves 2.18 percentage point increase in electrical efficiency, while simultaneously lowering total irreversibility and improving the improvement potential of key components.
- 13 May 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 240 (14) , 2033-2048
Experimental and numerical study on the impact of shock wave intensity on film cooling
In transonic high-load turbines, interactions between trailing-edge shock waves and suction-side film cooling can severely compromise thermal protection and may even lead to localized cooling failure. To investigate the underlying mechanisms and critical effects associated with shock intensity, combined experimental and numerical studies are conducted at an inlet Mach number of 1.45. Weak to moderate shock interference is found to primarily accelerate the vorticity dissipation of the coolant-jet-induced counter-rotating vortex pair (CRVP). As shock intensity further increases, a normal shock forms above the interaction region and, under strong baroclinic effects, induces a sustained reversal of the CRVP, thereby leading to a rapid deterioration of film cooling effectiveness within the shock wave-film interaction region. To quantitatively characterize the severity of SWFI, a wall-pressure-based shock wave interaction intensity parameter (φ) is introduced. When φ exceeds 0.30, film cooling performance is observed to enter a markedly degraded regime. Entropy generation analysis demonstrates that viscous dissipation is the primary source of the entropy generation rate (EGR). Within the SWFI region, more than 70% of the total EGR originates from the coolant–mainstream shear layer, while direct shock-induced compression contributes negligibly.
- 13 May 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 240 (14) , 2033-2048
Experimental and numerical study on the impact of shock wave intensity on film cooling
In transonic high-load turbines, interactions between trailing-edge shock waves and suction-side film cooling can severely compromise thermal protection and may even lead to localized cooling failure. To investigate the underlying mechanisms and critical effects associated with shock intensity, combined experimental and numerical studies are conducted at an inlet Mach number of 1.45. Weak to moderate shock interference is found to primarily accelerate the vorticity dissipation of the coolant-jet-induced counter-rotating vortex pair (CRVP). As shock intensity further increases, a normal shock forms above the interaction region and, under strong baroclinic effects, induces a sustained reversal of the CRVP, thereby leading to a rapid deterioration of film cooling effectiveness within the shock wave-film interaction region. To quantitatively characterize the severity of SWFI, a wall-pressure-based shock wave interaction intensity parameter (φ) is introduced. When φ exceeds 0.30, film cooling performance is observed to enter a markedly degraded regime. Entropy generation analysis demonstrates that viscous dissipation is the primary source of the entropy generation rate (EGR). Within the SWFI region, more than 70% of the total EGR originates from the coolant–mainstream shear layer, while direct shock-induced compression contributes negligibly.
- 6 February 2026
- Published by Springer Nature in Journal of Thermal Science
- Vol. 35 (2) , 378-391
Experimental and Numerical Investigation of Unsteady Flow in Centripetal Turbine Cavity
- 6 February 2026
- Published by Springer Nature in Journal of Thermal Science
- Vol. 35 (2) , 378-391
Experimental and Numerical Investigation of Unsteady Flow in Centripetal Turbine Cavity
- 10 September 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (2) , 1-43
Understanding Unsteady Vortex Structure and Shedding Frequency of Cylindrical Hole Film Cooling: Insights From Experimental and Numerical Approaches
To enhance film cooling effectiveness and reduce mixing loss, it is imperative to understand the dynamics of the unsteady vortex system and its interaction with the mainstream flow. In this study, a comprehensive experimental investigation was conducted to assess the film cooling effectiveness of a flat-plate cylindrical hole, along with the structure of the vortex system and the frequency of vortex shedding. This was achieved using a variety of techniques including pressure-sensitive paint (PSP), particle image velocimetry (PIV), hot-wire anemometry, and dynamic pressure sensors. To complement the experimental findings, a detailed analysis of the evolution mechanisms of unsteady coherent vortices was performed using the detached eddy simulation (DES) numerical method. The findings of the study revealed that the Kelvin–Helmholtz (K–H) shear vortex patterns on the windward side undergo a transition from clockwise to counterclockwise rotation with increasing blowing ratios. Large-scale vortex sheds from the K–H shear vortices, ultimately evolving into the hairpin vortex in the downstream region. Additionally, the study proposed two evolution models for the vortex systems in the film cooling flow field at different blowing ratios and elucidated the evolution mechanisms of counter-rotating vortex pair (CRVP). The results of the spectral analysis revealed a notable discrepancy in the slopes of the eigenfrequencies, which could be attributed to variations in the evolution patterns of the vortex systems.
- 10 September 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (2) , 1-43
Understanding Unsteady Vortex Structure and Shedding Frequency of Cylindrical Hole Film Cooling: Insights From Experimental and Numerical Approaches
To enhance film cooling effectiveness and reduce mixing loss, it is imperative to understand the dynamics of the unsteady vortex system and its interaction with the mainstream flow. In this study, a comprehensive experimental investigation was conducted to assess the film cooling effectiveness of a flat-plate cylindrical hole, along with the structure of the vortex system and the frequency of vortex shedding. This was achieved using a variety of techniques including pressure-sensitive paint (PSP), particle image velocimetry (PIV), hot-wire anemometry, and dynamic pressure sensors. To complement the experimental findings, a detailed analysis of the evolution mechanisms of unsteady coherent vortices was performed using the detached eddy simulation (DES) numerical method. The findings of the study revealed that the Kelvin–Helmholtz (K–H) shear vortex patterns on the windward side undergo a transition from clockwise to counterclockwise rotation with increasing blowing ratios. Large-scale vortex sheds from the K–H shear vortices, ultimately evolving into the hairpin vortex in the downstream region. Additionally, the study proposed two evolution models for the vortex systems in the film cooling flow field at different blowing ratios and elucidated the evolution mechanisms of counter-rotating vortex pair (CRVP). The results of the spectral analysis revealed a notable discrepancy in the slopes of the eigenfrequencies, which could be attributed to variations in the evolution patterns of the vortex systems.
- Open Access
- 13 October 2023
- Published by Elsevier in Energy Reviews
- Vol. 2 (4)
Advancements in compressed air engine technology and power system integration: A comprehensive review
- 13 October 2023
- Published by Elsevier in Energy Reviews
- Vol. 2 (4)
Open AccessAdvancements in compressed air engine technology and power system integration: A comprehensive review
- 22 December 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 237 (12) , 2696-2713
Adaptive prediction of turbine profile loss and multi-objective optimization in a wide incidence range
The loss prediction model plays a crucial role in turbine design for fast performance prediction and a shorter design cycle. Owing to the design requirements of high-efficiency turbines under a wide range of operating conditions, the loss prediction of the off-design incidence is increasingly important. However, limited by the modeling database and traditional modeling methods, the accuracy and adaptability of the existing off-design incidence loss predictions are insufficient. This paper proposes an adaptive prediction method based on machine learning and develops a multi-objective optimization process based on adaptive prediction. Machine learning (neural network) is applied for more flexible and accurate loss predictions over a wide incidence range. Compared with two classic loss models (Ainley and Mathieson model and Benner model), the adaptive prediction model significantly improves the ability to predict turbine profile loss with off-design incidence, particularly under large incidence conditions. The prediction root mean square error can be reduced by up to 73.8% (absolute value: 0.063). Furthermore, the multi-objective optimization method based on adaptive prediction is applied to the aerodynamic optimization of the original cascades with a wide incidence range. The weighted objective of the optimized cascade (Cri = 0.211) is reduced by 8.7% compared with that of the original cascade (Cri = 0.231). Within the range of full incidence angle (−40° to +20°), the variation of profile loss is reduced by 24.0%. This study is a preliminary exploration aimed at establishing an accurate turbine loss prediction system based on machine learning, the feasibility, and superiority of this approach are confirmed.
- 22 December 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 237 (12) , 2696-2713
Adaptive prediction of turbine profile loss and multi-objective optimization in a wide incidence range
The loss prediction model plays a crucial role in turbine design for fast performance prediction and a shorter design cycle. Owing to the design requirements of high-efficiency turbines under a wide range of operating conditions, the loss prediction of the off-design incidence is increasingly important. However, limited by the modeling database and traditional modeling methods, the accuracy and adaptability of the existing off-design incidence loss predictions are insufficient. This paper proposes an adaptive prediction method based on machine learning and develops a multi-objective optimization process based on adaptive prediction. Machine learning (neural network) is applied for more flexible and accurate loss predictions over a wide incidence range. Compared with two classic loss models (Ainley and Mathieson model and Benner model), the adaptive prediction model significantly improves the ability to predict turbine profile loss with off-design incidence, particularly under large incidence conditions. The prediction root mean square error can be reduced by up to 73.8% (absolute value: 0.063). Furthermore, the multi-objective optimization method based on adaptive prediction is applied to the aerodynamic optimization of the original cascades with a wide incidence range. The weighted objective of the optimized cascade (Cri = 0.211) is reduced by 8.7% compared with that of the original cascade (Cri = 0.231). Within the range of full incidence angle (−40° to +20°), the variation of profile loss is reduced by 24.0%. This study is a preliminary exploration aimed at establishing an accurate turbine loss prediction system based on machine learning, the feasibility, and superiority of this approach are confirmed.