Amir H. Roohi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Amir H. Roohi has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Ali Sadooghi
Department of Mechanical Engineering Technical and Vocational University (TVU) Tehran Iran
2 shared publications - Amir Dehghanghadikolaei
School of Mechanical, Industrial and Manufacturing Engineering, Oregon State University, Corvallis, OR 97331, USA
2 shared publications - Mohammad Hoseinpour Gollo
Faculty of Mechanical Engineering, Shahid Rajaee Teacher Training University, Tehran 16785-136, Iran
2 shared publications Reza Ghoreishi
Semnan University
2 shared publicationsS. J. Hashemi
Department of Mechanical Engineering, Faculty of Enghelab-e Eslami, Tehran Branch, Technical and Vocational University (TVU), Tehran, Iran
2 shared publicationsA. Ghiotti
Industrial Engineering Department, University of Padua, Padua, Italy
1 shared publication
Latest Publications
- Open Access
- 1 June 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (6) , 065006
Investigation of structural, mechanical, and corrosion properties of steel 316L reinforcement by hBN and TiC particles
The powder metallurgy process is commonly used to produce nanocomposite samples so that, their properties depend on the process parameters and the weight fraction of reinforcements. In the current study, producing metal matrix nanocomposite with steel 316L as a matrix and mixing of hBN/TiC nanoparticles as a reinforcement is conducted. The total weight percentages of reinforcements are 6% wt and 8% wt (i.e. with an equal proportion for each nanoparticle). The powders were mixed for 10 h and then compacted at different pressures (300 MPa and 400 MPa) by cold isostatic pressure (CIP) conditions. The compacted powders were sintered at different temperatures (1350 °C and 1450 °C), and times (2 h and 4 h) in the furnace. The microstructural analysis of nanocomposite was performed by SEM, XRD, EDX, DTA, and also FT-IR tests. The results showed that by increasing the weight fraction of nanoparticles the microhardness and wear rate improved and, on the contrary, the flexural strength and corrosion rate decreased. The optimum result for the microhardness and wear rate were achieved when the sample contains 8% wt nanoparticles, compacted at 400 MPa and sintered at 1350 °C for 4 h. As well, the highest flexural strength and corrosion rate belong to the sample compacted and sintered at 400 MPa, 1450 °C for 2 h.
- 1 June 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (6) , 065006
Open AccessInvestigation of structural, mechanical, and corrosion properties of steel 316L reinforcement by hBN and TiC particles
The powder metallurgy process is commonly used to produce nanocomposite samples so that, their properties depend on the process parameters and the weight fraction of reinforcements. In the current study, producing metal matrix nanocomposite with steel 316L as a matrix and mixing of hBN/TiC nanoparticles as a reinforcement is conducted. The total weight percentages of reinforcements are 6% wt and 8% wt (i.e. with an equal proportion for each nanoparticle). The powders were mixed for 10 h and then compacted at different pressures (300 MPa and 400 MPa) by cold isostatic pressure (CIP) conditions. The compacted powders were sintered at different temperatures (1350 °C and 1450 °C), and times (2 h and 4 h) in the furnace. The microstructural analysis of nanocomposite was performed by SEM, XRD, EDX, DTA, and also FT-IR tests. The results showed that by increasing the weight fraction of nanoparticles the microhardness and wear rate improved and, on the contrary, the flexural strength and corrosion rate decreased. The optimum result for the microhardness and wear rate were achieved when the sample contains 8% wt nanoparticles, compacted at 400 MPa and sintered at 1350 °C for 4 h. As well, the highest flexural strength and corrosion rate belong to the sample compacted and sintered at 400 MPa, 1450 °C for 2 h.
- Open Access
- 4 March 2021
- Published by Springer Nature in SN Applied Sciences
- Vol. 3 (4) , 1-10
Fabrication of aluminum bipolar plates with Archimedes' screw-shaped channels: a rubber pad forming process assessment
Bipolar plates are one of the most important components of polymer membrane fuel cells. In this manuscript, the rubber pad forming of aluminum bipolar plates with Archimedes' screw-shaped channels and draft angle of 90 $$^\circ$$ has been investigated. Hence, all possible combinations of the process parameters were determined and corresponding experimentations performed in order to investigate the effects of the rubber hardness, punch speed and the hydraulic press force. In this regard, three rubber pads including polyurethane, silicone and natural rubber were used. Channel depth and thinning percentage in the corner of the channel are measured and the effect of each parameter is analyzed. Based on the results, the maximum channel depth was achieved using a silicone pad with a hardness of 60 Shore A. Using a rubber pad with a very high and low hardness number, both, reduces the depth of channel. Furthermore, as the punch speed increases, the channel depth increases and the thinning percentage, as well.- 4 March 2021
- Published by Springer Nature in SN Applied Sciences
- Vol. 3 (4) , 1-10
Open AccessFabrication of aluminum bipolar plates with Archimedes' screw-shaped channels: a rubber pad forming process assessment
Bipolar plates are one of the most important components of polymer membrane fuel cells. In this manuscript, the rubber pad forming of aluminum bipolar plates with Archimedes' screw-shaped channels and draft angle of 90 $$^\circ$$ has been investigated. Hence, all possible combinations of the process parameters were determined and corresponding experimentations performed in order to investigate the effects of the rubber hardness, punch speed and the hydraulic press force. In this regard, three rubber pads including polyurethane, silicone and natural rubber were used. Channel depth and thinning percentage in the corner of the channel are measured and the effect of each parameter is analyzed. Based on the results, the maximum channel depth was achieved using a silicone pad with a hardness of 60 Shore A. Using a rubber pad with a very high and low hardness number, both, reduces the depth of channel. Furthermore, as the punch speed increases, the channel depth increases and the thinning percentage, as well. - 1 March 2021
- Vol. 14 (1) , 43-49
Hole-flanging of 2205 Dual-Phase Steel using Incremental Forming Process
- 1 March 2021
- Vol. 14 (1) , 43-49
Hole-flanging of 2205 Dual-Phase Steel using Incremental Forming Process
- Open Access
- 3 February 2021
- Published by Springer Nature in SN Applied Sciences
- Vol. 3 (2) , 1-25
Immersed boundary method for MHD unsteady natural convection around a hot elliptical cylinder in a cold rhombus enclosure filled with a nanofluid
In this study, the numerical investigation of the natural convection heat transfer around a hot elliptical cylinder inside a cold rhombus enclosure filled with a nanofluid in the presence of a uniform magnetic field is conducted. An immersed boundary method as a computational tool has been extended and applied to solve the problem. The influence of various parameters such as cylinder diameters (a, b), Hartmann number (Ha = 0, 50 and 100), nanofluid volume fraction ( $$\varphi = 0 , 2.5\% and 5\%$$ ), and Rayleigh number (Ra = 103, 104, 105, 106, and 107) has been studied. Streamlines and isotherms contours as well as average Nusselt number have been specified for different modes. An equation for the average Nusselt number as a function of mentioned parameters is presented in this paper. The results show that at lower Ra numbers of Ra = 103 and 104, the magnetic field effect is negligible. However, at higher Rayleigh numbers, the average Nusselt number (Nuave) decreases with the increasing Ha number. The maximum decrease in Nuave at Ra = 105, 106 and 107are calculated −8.15%, −23.4% and −27.3%, respectively. An asymmetry-unsteady flow is observed at $${\text{Ra}} = 10^{7}$$ for Ha = 0. However, at higher Ha numbers a steady-symmetrical flow is formed.- 3 February 2021
- Published by Springer Nature in SN Applied Sciences
- Vol. 3 (2) , 1-25
Open AccessImmersed boundary method for MHD unsteady natural convection around a hot elliptical cylinder in a cold rhombus enclosure filled with a nanofluid
In this study, the numerical investigation of the natural convection heat transfer around a hot elliptical cylinder inside a cold rhombus enclosure filled with a nanofluid in the presence of a uniform magnetic field is conducted. An immersed boundary method as a computational tool has been extended and applied to solve the problem. The influence of various parameters such as cylinder diameters (a, b), Hartmann number (Ha = 0, 50 and 100), nanofluid volume fraction ( $$\varphi = 0 , 2.5\% and 5\%$$ ), and Rayleigh number (Ra = 103, 104, 105, 106, and 107) has been studied. Streamlines and isotherms contours as well as average Nusselt number have been specified for different modes. An equation for the average Nusselt number as a function of mentioned parameters is presented in this paper. The results show that at lower Ra numbers of Ra = 103 and 104, the magnetic field effect is negligible. However, at higher Rayleigh numbers, the average Nusselt number (Nuave) decreases with the increasing Ha number. The maximum decrease in Nuave at Ra = 105, 106 and 107are calculated −8.15%, −23.4% and −27.3%, respectively. An asymmetry-unsteady flow is observed at $${\text{Ra}} = 10^{7}$$ for Ha = 0. However, at higher Ha numbers a steady-symmetrical flow is formed. - Open Access
- 1 January 2021
- Vol. 8 (1) , 4-13
Forming of Archimedean Spiral Bipolar Plates using Hot Gas Forming Process and its Characteristics Evaluation
- 1 January 2021
- Vol. 8 (1) , 4-13
Open AccessForming of Archimedean Spiral Bipolar Plates using Hot Gas Forming Process and its Characteristics Evaluation
- 23 September 2019
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 54 (8) , 1001-1011
Bending strength and notched-sample fatigue life of hBN/TiC-reinforced steel 316 L: A numerical and experimental analysis
Mechanical failure under cyclic and dynamic loading has always been a concern in engineering applications. Many different properties can be achieved by adding different materials to the metal matrix nanocomposites. In this study, steel 316 L is selected as the matrix, and the additive materials of titanium carbide and hexagonal boron nitride in 3.5 wt% for each one are added as the reinforcement particles. The samples are fabricated by powder metallurgy, compacted in pressure of 410 MPa, and sintered in temperature of 1375℃ for 4 h. In addition, some pure steel 316 L samples were provided for comparison purposes. Numerical simulation of bending strength and fatigue life of the notched samples were conducted and verified with experimental tests on the mechanical parts. It appeared that the nanocomposite specimens present a higher mechanical reliability relative to the pure 316 L as a result of adding nanoparticles. Steel 316 L S–N curves of the notched samples are also obtained from numerical analysis.
- 23 September 2019
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 54 (8) , 1001-1011
Bending strength and notched-sample fatigue life of hBN/TiC-reinforced steel 316 L: A numerical and experimental analysis
Mechanical failure under cyclic and dynamic loading has always been a concern in engineering applications. Many different properties can be achieved by adding different materials to the metal matrix nanocomposites. In this study, steel 316 L is selected as the matrix, and the additive materials of titanium carbide and hexagonal boron nitride in 3.5 wt% for each one are added as the reinforcement particles. The samples are fabricated by powder metallurgy, compacted in pressure of 410 MPa, and sintered in temperature of 1375℃ for 4 h. In addition, some pure steel 316 L samples were provided for comparison purposes. Numerical simulation of bending strength and fatigue life of the notched samples were conducted and verified with experimental tests on the mechanical parts. It appeared that the nanocomposite specimens present a higher mechanical reliability relative to the pure 316 L as a result of adding nanoparticles. Steel 316 L S–N curves of the notched samples are also obtained from numerical analysis.
- 26 February 2019
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 41 (3) , 146
Evaluation of tool wear in high-speed face milling of Al/SiC metal matrix composites
- 26 February 2019
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 41 (3) , 146
Evaluation of tool wear in high-speed face milling of Al/SiC metal matrix composites
- 27 July 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (8) , 086521
Analysis of the influence of cutting parameters on surface roughness and cutting forces in high speed face milling of Al/SiC MMC
- 27 July 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (8) , 086521
Analysis of the influence of cutting parameters on surface roughness and cutting forces in high speed face milling of Al/SiC MMC
- 2 January 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 95 (9-12) , 3919-3928
Forming of closed-cell aluminum foams under thermal loadings: experimental investigation
- 2 January 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 95 (9-12) , 3919-3928
Forming of closed-cell aluminum foams under thermal loadings: experimental investigation
- 1 January 2018
- Published by Elsevier in Optics & Laser Technology
- Vol. 98, 121-133
Codification of scan path parameters and development of perimeter scan strategies for 3D bowl-shaped laser forming
- 1 January 2018
- Published by Elsevier in Optics & Laser Technology
- Vol. 98, 121-133
Codification of scan path parameters and development of perimeter scan strategies for 3D bowl-shaped laser forming