Vuong Van Cuong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Vuong Van Cuong has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Shin-Ichiro Kuroki
Hiroshima University
11 shared publications Hiroshi Sezaki
Phenitec Semiconductor Corp., Okayama, Japan
9 shared publicationsSeiji Ishikawa
Phenitec Semiconductor Corp., Okayama, Japan
9 shared publicationsTomonori Maeda
Phenitec Semiconductor Corp., Okayama, Japan
9 shared publicationsTakamichi Miyazaki
School of Engineering, Tohoku University, Aramaki, Aoba-ku, Sendai, 980-8579, Japan
5 shared publications- Tatsuya Meguro
Hiroshima University
5 shared publications
Latest Publications
- 1 May 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (5) , 056503
High-temperature reliability of Ni/Ti/Nb ohmic contact on p-type 4H-SiC
In this study, the thermal stability of Ni/Ti and Ni/Ti/Nb ohmic contact on p-type 4H-SiC were investigated for 100 h at 400 °C in N2 environment. The results demonstrated that lower contact resistance and higher thermal stability could be achieved with the Ni/Ti/Nb candidate. After 100 h aging, the specific contact resistance of the Ni/Ti/Nb sample slightly increased from 2.56 × 10−3 to 3.04 × 10−3 Ω cm2. X-ray diffraction results showed that Ni2Si, Ti3SiC2 and Nb6C5 compounds contributed to low contact resistance and high-temperature reliability. By adding Nb, the surface of the Ni/Ti/Nb/4H-SiC ohmic contact becomes smoother than that of the Ni/Ti/4H-SiC ohmic contact. The metal/4H-SiC interface of the ohmic contacts was observed after 100 h aging by using TEM measurement. For the Ni/Ti/Nb sample, the excess carbon atoms were collected by the formation of Nb–C compounds and then increased high temperature reliability and reduced contact resistivity.
- 1 May 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (5) , 056503
High-temperature reliability of Ni/Ti/Nb ohmic contact on p-type 4H-SiC
In this study, the thermal stability of Ni/Ti and Ni/Ti/Nb ohmic contact on p-type 4H-SiC were investigated for 100 h at 400 °C in N2 environment. The results demonstrated that lower contact resistance and higher thermal stability could be achieved with the Ni/Ti/Nb candidate. After 100 h aging, the specific contact resistance of the Ni/Ti/Nb sample slightly increased from 2.56 × 10−3 to 3.04 × 10−3 Ω cm2. X-ray diffraction results showed that Ni2Si, Ti3SiC2 and Nb6C5 compounds contributed to low contact resistance and high-temperature reliability. By adding Nb, the surface of the Ni/Ti/Nb/4H-SiC ohmic contact becomes smoother than that of the Ni/Ti/4H-SiC ohmic contact. The metal/4H-SiC interface of the ohmic contacts was observed after 100 h aging by using TEM measurement. For the Ni/Ti/Nb sample, the excess carbon atoms were collected by the formation of Nb–C compounds and then increased high temperature reliability and reduced contact resistivity.
- Open Access
- 3 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 13, 161-167
Thermal Stability of Gate Driver Circuits Based on 4H-SiC MOSFETs at 300°C for High-Power Applications
The operation and reliability of gate driver circuits based on 4H-SiC MOSFETs at temperatures up to 300∘ C were reported. Due to the advantages of 4H-SiC MOSFETs, the driver circuit can overcome limitations in complicated circuit design and power dissipation associated with SiC BJT-based technology. Additionally, the stability of implanted 4H-SiC resistors can address the reliability issues of SiC CMOS-based driver circuits, which are caused by the instability in the threshold voltage of P-channel SiC MOSFETs. In this study, the switching characteristics of the gate driver circuit were improved when the ambient temperature increased. The decrease of threshold voltage and increase of carrier mobility of the 4H-SiC MOSFETs may account for the improvement in switching characteristics of the gate driver circuit. The output signal of the gate driver circuit still showed proper characteristics after 600 min of continuous operation at 300∘ C in an air ambient. These results indicate that the gate driver circuit based on 4H-SiC MOSFET technology is promising to apply for high power applications.
- 3 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 13, 161-167
Open AccessThermal Stability of Gate Driver Circuits Based on 4H-SiC MOSFETs at 300°C for High-Power Applications
The operation and reliability of gate driver circuits based on 4H-SiC MOSFETs at temperatures up to 300∘ C were reported. Due to the advantages of 4H-SiC MOSFETs, the driver circuit can overcome limitations in complicated circuit design and power dissipation associated with SiC BJT-based technology. Additionally, the stability of implanted 4H-SiC resistors can address the reliability issues of SiC CMOS-based driver circuits, which are caused by the instability in the threshold voltage of P-channel SiC MOSFETs. In this study, the switching characteristics of the gate driver circuit were improved when the ambient temperature increased. The decrease of threshold voltage and increase of carrier mobility of the 4H-SiC MOSFETs may account for the improvement in switching characteristics of the gate driver circuit. The output signal of the gate driver circuit still showed proper characteristics after 600 min of continuous operation at 300∘ C in an air ambient. These results indicate that the gate driver circuit based on 4H-SiC MOSFET technology is promising to apply for high power applications.
- 1 August 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (8) , 086503
Thermal stability of TiN gate electrode for 4H-SiC MOSFETs and integrated circuits
In this research, the thermal stability of single-stage amplifiers based on a 4H-SiC MOSFET with a TiN gate electrode was investigated. The results show that after 100 h aging at 400 °C in N2 ambient, the amplifier maintained good performance with stable voltage gain. The thermal stability of the amplifier is attributed to the stability of Ni/Nb/4H-SiC source/drain ohmic contact, implanted load resistor, and MOS structure with the TiN gate electrode. The results obtained from the 4H-SiC MOS structure show that the interface trap density at the SiO2/SiC decreases during the aging process. While the gate leakage current of the capacitor based on the Al gate electrode increases, it remains stable in structures with TiN gate electrodes after 100 h aging. The results obtained in this study indicate that TiN is promising for the gate electrode of 4H-SiC MOSFETs for high-temperature applications.
- 1 August 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (8) , 086503
Thermal stability of TiN gate electrode for 4H-SiC MOSFETs and integrated circuits
In this research, the thermal stability of single-stage amplifiers based on a 4H-SiC MOSFET with a TiN gate electrode was investigated. The results show that after 100 h aging at 400 °C in N2 ambient, the amplifier maintained good performance with stable voltage gain. The thermal stability of the amplifier is attributed to the stability of Ni/Nb/4H-SiC source/drain ohmic contact, implanted load resistor, and MOS structure with the TiN gate electrode. The results obtained from the 4H-SiC MOS structure show that the interface trap density at the SiO2/SiC decreases during the aging process. While the gate leakage current of the capacitor based on the Al gate electrode increases, it remains stable in structures with TiN gate electrodes after 100 h aging. The results obtained in this study indicate that TiN is promising for the gate electrode of 4H-SiC MOSFETs for high-temperature applications.
- Open Access
- 1 January 2024
- Published by National Library of Serbia in Facta universitatis - series: Electronics and Energetics
- Vol. 37 (4) , 599-607
Impact of interface oxide type on the gamma radiation response of SiC TTL ICs
In this study, we investigate the impact of Gamma Radiation on 4H Silicon Carbide (SiC) Transistor-Transistor Logic (TTL) integrated circuits (ICs), particularly focusing on inverters processed with distinct types of interface oxides: Thermally Grown, Chemical Vapor Deposition, and Atomic Layer Deposition. This research was conducted using a 60Co source at Hiroshima University, applying varied radiation doses (17.9 rad(Si)/s, 7.3 rad(Si)/s, and 2.47 rad(Si)/s) to assess the resilience of the SiC inverters under these conditions. Our findings reveal that thermal oxides (Batch 1: W1 and W2) demonstrate higher radiation resilience compared to ALD and CVD interface oxides (Batch 2: W3 and W4), attributable to their denser structure and fewer defects. The study also identifies that while the inverters exhibit marginal degradation at gamma doses nearing 700 krad (under 6%), the most critical operational state is the passive mode (VCC = VIN = 0 V), where the build-up of induced charge in the oxide and interface may lead to early IC degradation of the noise margins. The outcomes from this research provide insights into the processing flow and enhancement of SiC electronics. Our results underscore the potential of SiC-based ICs in environments with high radiation levels, such as space missions, nuclear reactors, and medical applications, due to their enhanced radiation tolerance.
- 1 January 2024
- Published by National Library of Serbia in Facta universitatis - series: Electronics and Energetics
- Vol. 37 (4) , 599-607
Open AccessImpact of interface oxide type on the gamma radiation response of SiC TTL ICs
In this study, we investigate the impact of Gamma Radiation on 4H Silicon Carbide (SiC) Transistor-Transistor Logic (TTL) integrated circuits (ICs), particularly focusing on inverters processed with distinct types of interface oxides: Thermally Grown, Chemical Vapor Deposition, and Atomic Layer Deposition. This research was conducted using a 60Co source at Hiroshima University, applying varied radiation doses (17.9 rad(Si)/s, 7.3 rad(Si)/s, and 2.47 rad(Si)/s) to assess the resilience of the SiC inverters under these conditions. Our findings reveal that thermal oxides (Batch 1: W1 and W2) demonstrate higher radiation resilience compared to ALD and CVD interface oxides (Batch 2: W3 and W4), attributable to their denser structure and fewer defects. The study also identifies that while the inverters exhibit marginal degradation at gamma doses nearing 700 krad (under 6%), the most critical operational state is the passive mode (VCC = VIN = 0 V), where the build-up of induced charge in the oxide and interface may lead to early IC degradation of the noise margins. The outcomes from this research provide insights into the processing flow and enhancement of SiC electronics. Our results underscore the potential of SiC-based ICs in environments with high radiation levels, such as space missions, nuclear reactors, and medical applications, due to their enhanced radiation tolerance.
- Open Access
- 1 January 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (1) , 015503
Study of interface-trap and near-interface-state distribution in a 4H-SiC MOS capacitor with the full-distributed circuit model
In this research, the full-distributed circuit model was used to classify the contribution of interface traps (ITs) and near-interface states to the electrical characteristics of a 4H-SiC MOS capacitor over a wide range of operation. By fitting the measured capacitance and conductance at a certain value of applied gate voltage when the frequency varied from 1 kHz to 1 MHz, the density of both near-interface states and ITs was determined. The results reveal that, at RT, the frequency dispersion of capacitance in the depletion condition is mainly caused by the contribution of ITs. Nevertheless, in the strong accumulation condition, near-interface states become dominant for the frequency dispersion of the capacitance. Furthermore, the full-distributed circuit model also successfully explained the electrical characteristics of a 4H-SiC MOS capacitor when operating at 500 °C.
- 1 January 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (1) , 015503
Open AccessStudy of interface-trap and near-interface-state distribution in a 4H-SiC MOS capacitor with the full-distributed circuit model
In this research, the full-distributed circuit model was used to classify the contribution of interface traps (ITs) and near-interface states to the electrical characteristics of a 4H-SiC MOS capacitor over a wide range of operation. By fitting the measured capacitance and conductance at a certain value of applied gate voltage when the frequency varied from 1 kHz to 1 MHz, the density of both near-interface states and ITs was determined. The results reveal that, at RT, the frequency dispersion of capacitance in the depletion condition is mainly caused by the contribution of ITs. Nevertheless, in the strong accumulation condition, near-interface states become dominant for the frequency dispersion of the capacitance. Furthermore, the full-distributed circuit model also successfully explained the electrical characteristics of a 4H-SiC MOS capacitor when operating at 500 °C.
- 29 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (8) , 4194-4199
Amplifier Based on 4H-SiC MOSFET Operation at 500 °C for Harsh Environment Applications
Successful operation of 4H-silicon carbide (SiC) MOSFET and integrated electronic circuit based on 4H-SiC MOSFET is reported at temperature up to$500~^{\circ }\text{C}$ in air. The high-temperature operation of the integrated circuit (IC) based on 4H-SiC MOSFET strongly depends on the reliability of metal/SiC contact. Based on the transfer length method (TLM), the Ni/Nb/n-type 4H-SiC junction exhibits ohmic behavior with specific contact resistance of$1.86\times 10^{-{4}}\,\, \Omega \cdot $ cm 2 when operating at$500~^{\circ }\text{C}$ . In contrast, the voltage gain of the amplifier is strongly governed by the variation of carrier mobility of the 4H-SiC MOSFET when temperature varies from room temperature to$500~^{\circ }\text{C}$ . The experimental results show that, when the temperature is increased from$20~^{\circ }\text{C}$ to$300~^{\circ }\text{C}$ , the amplifier gain of the IC increased from 23.8 to 153.0. Though the voltage gain decreases when the temperature increases above$300~^{\circ }\text{C}$ , it is still higher than 50 at$500~^{\circ }\text{C}$ . These results indicate that integrated electronic circuits based on this 4H-SiC MOSFET technology could be potentially used for harsh environment applications.- 29 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (8) , 4194-4199
Amplifier Based on 4H-SiC MOSFET Operation at 500 °C for Harsh Environment Applications
Successful operation of 4H-silicon carbide (SiC) MOSFET and integrated electronic circuit based on 4H-SiC MOSFET is reported at temperature up to$500~^{\circ }\text{C}$ in air. The high-temperature operation of the integrated circuit (IC) based on 4H-SiC MOSFET strongly depends on the reliability of metal/SiC contact. Based on the transfer length method (TLM), the Ni/Nb/n-type 4H-SiC junction exhibits ohmic behavior with specific contact resistance of$1.86\times 10^{-{4}}\,\, \Omega \cdot $ cm 2 when operating at$500~^{\circ }\text{C}$ . In contrast, the voltage gain of the amplifier is strongly governed by the variation of carrier mobility of the 4H-SiC MOSFET when temperature varies from room temperature to$500~^{\circ }\text{C}$ . The experimental results show that, when the temperature is increased from$20~^{\circ }\text{C}$ to$300~^{\circ }\text{C}$ , the amplifier gain of the IC increased from 23.8 to 153.0. Though the voltage gain decreases when the temperature increases above$300~^{\circ }\text{C}$ , it is still higher than 50 at$500~^{\circ }\text{C}$ . These results indicate that integrated electronic circuits based on this 4H-SiC MOSFET technology could be potentially used for harsh environment applications.- 18 February 2022
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 61 (3) , 036501
500 °C high-temperature reliability of Ni/Nb ohmic contact on n-type 4H-SiC
The reliability of Ni/Nb ohmic contact on n-type 4H-SiC at 500 °C was investigated. The current–voltage characteristics showed that, while the Ni(50)/Nb(50)/4H-SiC sample without applying the CF 4 :O 2 etching process degraded just after 25 h and lost ohmic behavior after 50 h aging, the Ni(75)/Nb(25)/4H-SiC contact undergone CF 4 :O 2 surface treatment still showed excellent stability after aging for 100 h at 500 °C. Though X-ray diffraction results indicated that the chemical compounds remained stable during the aging process, transmission electron microscopy showed that there was a redistribution of the chemical compounds at the interface of the contact after 500 °C aging. The depth distribution of the elements and energy-dispersive X-ray analyses revealed that the contribution of carbon agglomeration at the interface accounted for the degradation of the sample without applying the etching process. Whereas the well-controlled excess carbon atoms of the contact undergone CF 4 :O 2 treatment ensured the stability of this contact when operating at a high ambient temperature.
- 18 February 2022
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 61 (3) , 036501
500 °C high-temperature reliability of Ni/Nb ohmic contact on n-type 4H-SiC
The reliability of Ni/Nb ohmic contact on n-type 4H-SiC at 500 °C was investigated. The current–voltage characteristics showed that, while the Ni(50)/Nb(50)/4H-SiC sample without applying the CF 4 :O 2 etching process degraded just after 25 h and lost ohmic behavior after 50 h aging, the Ni(75)/Nb(25)/4H-SiC contact undergone CF 4 :O 2 surface treatment still showed excellent stability after aging for 100 h at 500 °C. Though X-ray diffraction results indicated that the chemical compounds remained stable during the aging process, transmission electron microscopy showed that there was a redistribution of the chemical compounds at the interface of the contact after 500 °C aging. The depth distribution of the elements and energy-dispersive X-ray analyses revealed that the contribution of carbon agglomeration at the interface accounted for the degradation of the sample without applying the etching process. Whereas the well-controlled excess carbon atoms of the contact undergone CF 4 :O 2 treatment ensured the stability of this contact when operating at a high ambient temperature.
- 25 November 2020
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 59 (12) , 126504
High-temperature reliability of integrated circuit based on 4H-SiC MOSFET with Ni/Nb ohmic contacts for harsh environment applications
The high-temperature reliability of integrated circuit based on 4H-SiC MOSFET with Ni/Nb ohmic contacts was investigated at 400 °C in N 2 ambient. The results showed that the single stage amplifier remained a stable voltage gain after 100 h of aging at 400 °C. Based on the transfer length method, the Ni/Nb/n-type 4H-SiC ohmic contact exhibited the excellent stability after being aged at 400 °C for 100 h. Whereas, the stability of electrical characteristics indicated that the 4H-SiC MOSFET also exhibited a good stability when operating in high temperature environment. Moreover, the stability of the electrical characteristics of the 4H-SiC MOS capacitor showed that the reliability of the Ni/Nb/4H-SiC ohmic contact played important role in reliability of SiC based devices. These results indicate that the fabrication process of the integrated circuits based on 4H-SiC devices with Ni/Nb ohmic contacts is promising to apply for high temperature as well as harsh environment applications.
- 25 November 2020
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 59 (12) , 126504
High-temperature reliability of integrated circuit based on 4H-SiC MOSFET with Ni/Nb ohmic contacts for harsh environment applications
The high-temperature reliability of integrated circuit based on 4H-SiC MOSFET with Ni/Nb ohmic contacts was investigated at 400 °C in N 2 ambient. The results showed that the single stage amplifier remained a stable voltage gain after 100 h of aging at 400 °C. Based on the transfer length method, the Ni/Nb/n-type 4H-SiC ohmic contact exhibited the excellent stability after being aged at 400 °C for 100 h. Whereas, the stability of electrical characteristics indicated that the 4H-SiC MOSFET also exhibited a good stability when operating in high temperature environment. Moreover, the stability of the electrical characteristics of the 4H-SiC MOS capacitor showed that the reliability of the Ni/Nb/4H-SiC ohmic contact played important role in reliability of SiC based devices. These results indicate that the fabrication process of the integrated circuits based on 4H-SiC devices with Ni/Nb ohmic contacts is promising to apply for high temperature as well as harsh environment applications.
- 29 April 2020
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 59 (5) , 056501
CF 4 :O 2 surface etching for the improvement of contact resistance and high-temperature reliability in Ni/Nb ohmic contacts on n-type 4H-SiC
The influence of CF 4 :O 2 surface etching on the formation of Ni/Nb ohmic contact to n-type 4H-SiC substrates was investigated. The specific contact resistivity extracted from the transmission line model showed that the contact with CF 4 :O 2 etching had lower contact resistance than that of the sample without the etching process. The X-ray diffraction results showed that a higher concentration of Ni 2 Si formed at the interface of the contact after the fabrication process resulted in a lower specific contact resistivity. Moreover, the depth distribution of the elements revealed that under the CF 4 :O 2 surface etching, a low density of the excess carbon atoms at the interface of the contact was observed. Transmission electron microscopy also confirmed that the low concentration of excess carbon atoms and the high density of Ni 2 Si at the interface play an important role in low specific contact resistivity as well as the high temperature reliability of the Ni/Nb/4H-SiC contacts undergoing CF 4 :O 2 treatment.
- 29 April 2020
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 59 (5) , 056501
CF 4 :O 2 surface etching for the improvement of contact resistance and high-temperature reliability in Ni/Nb ohmic contacts on n-type 4H-SiC
The influence of CF 4 :O 2 surface etching on the formation of Ni/Nb ohmic contact to n-type 4H-SiC substrates was investigated. The specific contact resistivity extracted from the transmission line model showed that the contact with CF 4 :O 2 etching had lower contact resistance than that of the sample without the etching process. The X-ray diffraction results showed that a higher concentration of Ni 2 Si formed at the interface of the contact after the fabrication process resulted in a lower specific contact resistivity. Moreover, the depth distribution of the elements revealed that under the CF 4 :O 2 surface etching, a low density of the excess carbon atoms at the interface of the contact was observed. Transmission electron microscopy also confirmed that the low concentration of excess carbon atoms and the high density of Ni 2 Si at the interface play an important role in low specific contact resistivity as well as the high temperature reliability of the Ni/Nb/4H-SiC contacts undergoing CF 4 :O 2 treatment.
- Open Access
- 5 March 2020
- Published by Publishing House for Science and Technology, Vietnam Academy of Science and Technology (Publications) in Communications in Physics
- Vol. 30 (1) , 79
Two-colour Three-pulse Spectrally Resolved Nonlinear Spectroscopy for Studies of Dynamics in Semiconductor Si Quantum Dots
We demonstrate that a two-colour three-pulsenonlinear spectroscopy can be used to study the dynamics of excited carriers inSi quantum dot structures embedded in SiN. Decays of the transverse optical phonon population and the transverse acoustic phonon population are measured and discussed. A simple theoretical modelis also used to support interpretation of our experimental observations.
- 5 March 2020
- Published by Publishing House for Science and Technology, Vietnam Academy of Science and Technology (Publications) in Communications in Physics
- Vol. 30 (1) , 79
Open AccessTwo-colour Three-pulse Spectrally Resolved Nonlinear Spectroscopy for Studies of Dynamics in Semiconductor Si Quantum Dots
We demonstrate that a two-colour three-pulsenonlinear spectroscopy can be used to study the dynamics of excited carriers inSi quantum dot structures embedded in SiN. Decays of the transverse optical phonon population and the transverse acoustic phonon population are measured and discussed. A simple theoretical modelis also used to support interpretation of our experimental observations.