Radosław Łyszkowski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Radosław Łyszkowski has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Jerzy Bystrzycki
3 shared publications- Tomasz Czujko
Institute of Materials Science and Engineering, Military University of Technology, Kaliskiego 2, 00-908 Warsaw, Poland
3 shared publications - Wojciech Polkowski
Łukasiewicz Research Network—Krakow Institute of Technology, Zakopiańska 73 Str., 30-418 Kraków, Poland
3 shared publications - Paweł Jóźwik
Faculty of Advanced Technologies and Chemistry, Institute of Materials Science and Engineering, Military University of Technology, Kaliskiego 2 Str., 00-908 Warsaw, Poland
2 shared publications - Zbigniew Bojar
Faculty of Advanced Technologies and Chemistry, Military University of Technology, Sylwestra Kaliskiego 2, 00-908 Warsaw, Poland
2 shared publications Anna Fraczkiewicz
Ecole Nationale Superieure des Mines de Saint Etienne, 158 Cours Fauriel, Saint-Etienne 42030, France
1 shared publication
Latest Publications
- Open Access
Influence of Strain Route Changes on the Microstructure and Mechanical Properties of CuZn36 Alloy during Cross Channel Extrusion CCE
This study evaluates the impact of changing the deformation routes of the extrusion process in a cross-shaped die (CCE) on the structure and properties of a CuZn36 alloy (% at.). Samples with dimensions of Ø8 × 36 mm were subjected to extrusion at room temperature according to two variants: straight extrusion in the A route (2-, 4-, 8- and 12-pass) and extrusion with interoperative rotation by 90° in the BC route (2- and 4-pass). The improvement of strength properties was obtained as a result of grain fragmentation in the CCE process. Changes in the microstructure were observed using a light microscope, and mechanical properties were measured in the microhardness test and a static tensile test. The obtained results showed that the mechanical properties of the alloy depend on the number of passes and the material deformation route. This observation was related to the fragmentation of its structure and strengthening, which resulted in changes in its properties. The highest strength was characterized by the material pressed four times with the rotation of 90° (BC route), whose properties were comparable and even slightly better than the material squeezed twelve times without rotation (A route).
Open AccessInfluence of Strain Route Changes on the Microstructure and Mechanical Properties of CuZn36 Alloy during Cross Channel Extrusion CCE
This study evaluates the impact of changing the deformation routes of the extrusion process in a cross-shaped die (CCE) on the structure and properties of a CuZn36 alloy (% at.). Samples with dimensions of Ø8 × 36 mm were subjected to extrusion at room temperature according to two variants: straight extrusion in the A route (2-, 4-, 8- and 12-pass) and extrusion with interoperative rotation by 90° in the BC route (2- and 4-pass). The improvement of strength properties was obtained as a result of grain fragmentation in the CCE process. Changes in the microstructure were observed using a light microscope, and mechanical properties were measured in the microhardness test and a static tensile test. The obtained results showed that the mechanical properties of the alloy depend on the number of passes and the material deformation route. This observation was related to the fragmentation of its structure and strengthening, which resulted in changes in its properties. The highest strength was characterized by the material pressed four times with the rotation of 90° (BC route), whose properties were comparable and even slightly better than the material squeezed twelve times without rotation (A route).
- Open Access
The Influence of A Cross-Channel Extrusion Process on The Microstructure and Properties of Copper
A new cross-channel extrusion (CCE) method with the application of a back pressure (BP) is proposed and experimentally tested. The introduction of pressure blocks the free flow of material by using an additional set of pistons, which prevents the loss of consistency. The paper presents results of experimental trials of CCE process. Between one and eight passes of CCE with and without a BP were applied to pure copper billets to refine their initial coarse-grained microstructure at room temperature. It was found that processing by CCE results in the formation of a lamellar structure along the extruded axis and the fine-grained structure in the remaining volume. The material exhibited dynamic recrystallization, which results in the formation of 0.5- to 2-μm grains after one pass and 2- to 8-μm grains after four CCE passes. The fine-grained material had YS of 390-415 MPa. An increase in the microhardness from 70 to 130 HV02 after one pass and then a decrease after four passes were observed. This might indicate that secondary recrystallization and selective grain growth occur, because an exothermic peak (158.5 °C, 53 ± 2.1 J/mol) was observed during DSC (differential scanning calorimetry) testing. The resistivity of the once deformed copper significantly decreases, while its further processing causes the resistivity to increase.
Open AccessThe Influence of A Cross-Channel Extrusion Process on The Microstructure and Properties of Copper
A new cross-channel extrusion (CCE) method with the application of a back pressure (BP) is proposed and experimentally tested. The introduction of pressure blocks the free flow of material by using an additional set of pistons, which prevents the loss of consistency. The paper presents results of experimental trials of CCE process. Between one and eight passes of CCE with and without a BP were applied to pure copper billets to refine their initial coarse-grained microstructure at room temperature. It was found that processing by CCE results in the formation of a lamellar structure along the extruded axis and the fine-grained structure in the remaining volume. The material exhibited dynamic recrystallization, which results in the formation of 0.5- to 2-μm grains after one pass and 2- to 8-μm grains after four CCE passes. The fine-grained material had YS of 390-415 MPa. An increase in the microhardness from 70 to 130 HV02 after one pass and then a decrease after four passes were observed. This might indicate that secondary recrystallization and selective grain growth occur, because an exothermic peak (158.5 °C, 53 ± 2.1 J/mol) was observed during DSC (differential scanning calorimetry) testing. The resistivity of the once deformed copper significantly decreases, while its further processing causes the resistivity to increase.
- Open Access
Severe Plastic Deformation of Fe-22Al-5Cr Alloy by Cross-Channel Extrusion with Back Pressure
A new concept of the cross-channel extrusion (CCE) process under back pressure (BP) was proposed and tested experimentally. The obtained by finite element method (FEM) results showed that a triaxial compression occurred in the central zone, whereas the material was deformed by shearing in the outer zone. This led to the presence of a relatively uniformly deformed outer zone at 1 per pass and a strong deformation of the paraxial zone (3–5/pass). An increase in the BP did not substantially affect the accumulated strain but made it more uniform. The FEM results were verified using the physical modeling technique (PMT) by the extrusion of clay billet. The formation of the plane of the strongly flattened, and elongated grains were observed in the extrusion directions. With the increase in the number of passes, the shape of the resulting patterns expanded, indicating an increase in the deformation homogeneity. Finally, these investigations were verified experimentally for Fe-22Al-5Cr (at. %) alloy using of the purposely designed tooling. The effect of the CCE process is the fragmentation of the original material structure by dividing the primary grains. The complexity of the stress state leads to the rapid growth of microshear bands (MSB), grain defragmentation and the nucleation of new dynamically recrystallized grains about 200–400 nm size.
Open AccessSevere Plastic Deformation of Fe-22Al-5Cr Alloy by Cross-Channel Extrusion with Back Pressure
A new concept of the cross-channel extrusion (CCE) process under back pressure (BP) was proposed and tested experimentally. The obtained by finite element method (FEM) results showed that a triaxial compression occurred in the central zone, whereas the material was deformed by shearing in the outer zone. This led to the presence of a relatively uniformly deformed outer zone at 1 per pass and a strong deformation of the paraxial zone (3–5/pass). An increase in the BP did not substantially affect the accumulated strain but made it more uniform. The FEM results were verified using the physical modeling technique (PMT) by the extrusion of clay billet. The formation of the plane of the strongly flattened, and elongated grains were observed in the extrusion directions. With the increase in the number of passes, the shape of the resulting patterns expanded, indicating an increase in the deformation homogeneity. Finally, these investigations were verified experimentally for Fe-22Al-5Cr (at. %) alloy using of the purposely designed tooling. The effect of the CCE process is the fragmentation of the original material structure by dividing the primary grains. The complexity of the stress state leads to the rapid growth of microshear bands (MSB), grain defragmentation and the nucleation of new dynamically recrystallized grains about 200–400 nm size.
- 16 November 2016
- Published by Wiley in Advanced Engineering Materials
- Vol. 19 (3) , 1600618
Differential Speed Rolling of Ni3Al‐Based Intermetallic Alloy − Electron Backscatter Diffraction and X‐Ray Diffraction Study on Structure and Texture Evolution
Results of electron backscatter diffraction and X‐ray diffraction study on a microstructure, long range order, and texture evolution upon a differential speed rolling (DSR) of Zr and B doped Ni3Al‐based intermetallic alloy, are shown in the paper. The material is subjected to a 2‐pass cold rolling to the final thickness reduction of 50% under following upper to lower roll speed ratio R values: R = 1 (the equal speed rolling), R = 2, R = 3, and R = 4 (the DSR). Obtained results supported by literature data allows concluding that an introduction of the rolls speed asymmetry leads to a higher accumulated strain facilitating a strain induced disordering of L12 superlattice. This transformation is assisted by a changeover of a crystallographic texture type; indirectly indicating on a possible activation of mechanical twinning.
- 16 November 2016
- Published by Wiley in Advanced Engineering Materials
- Vol. 19 (3) , 1600618
Differential Speed Rolling of Ni3Al‐Based Intermetallic Alloy − Electron Backscatter Diffraction and X‐Ray Diffraction Study on Structure and Texture Evolution
Results of electron backscatter diffraction and X‐ray diffraction study on a microstructure, long range order, and texture evolution upon a differential speed rolling (DSR) of Zr and B doped Ni3Al‐based intermetallic alloy, are shown in the paper. The material is subjected to a 2‐pass cold rolling to the final thickness reduction of 50% under following upper to lower roll speed ratio R values: R = 1 (the equal speed rolling), R = 2, R = 3, and R = 4 (the DSR). Obtained results supported by literature data allows concluding that an introduction of the rolls speed asymmetry leads to a higher accumulated strain facilitating a strain induced disordering of L12 superlattice. This transformation is assisted by a changeover of a crystallographic texture type; indirectly indicating on a possible activation of mechanical twinning.
- Open Access
- 15 November 2016
- Published by Springer Nature in Journal of Materials Science
- Vol. 52 (5) , 2902-2914
Multi-axial forging of Fe3Al-base intermetallic alloy and its mechanical properties
- 15 November 2016
- Published by Springer Nature in Journal of Materials Science
- Vol. 52 (5) , 2902-2914
Open AccessMulti-axial forging of Fe3Al-base intermetallic alloy and its mechanical properties
- 5 September 2016
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 107 (9) , 867-871
Effect of hot differential speed rolling on microstructure and mechanical properties of Fe3Al-based intermetallic alloy
Results of the first study on hot differential speed rolling (DSR) of Fe3Al-based intermetallic alloy are given in the present paper. The material was subjected to hot rolling at 1100°C with equal and non-equal (the DSR) speed of working rolls. The results of structural examinations indicate that the additional shear strain imposed to the material upon the DSR processing facilitates the activation of dynamic recrystallization. As opposed to the material hot deformed with equal speed of both rolls, the DSRed Fe3Al alloy was characterized by a fully transformed, close to equiaxed grain structure (average grain size of ∼120 μm). The observed structural evolution leads to a higher mechanical strength in DSRed samples as compared to the undeformed counterparts, however it does not result in a substantial improvement of the material's ductility.
- 5 September 2016
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 107 (9) , 867-871
Effect of hot differential speed rolling on microstructure and mechanical properties of Fe3Al-based intermetallic alloy
Results of the first study on hot differential speed rolling (DSR) of Fe3Al-based intermetallic alloy are given in the present paper. The material was subjected to hot rolling at 1100°C with equal and non-equal (the DSR) speed of working rolls. The results of structural examinations indicate that the additional shear strain imposed to the material upon the DSR processing facilitates the activation of dynamic recrystallization. As opposed to the material hot deformed with equal speed of both rolls, the DSRed Fe3Al alloy was characterized by a fully transformed, close to equiaxed grain structure (average grain size of ∼120 μm). The observed structural evolution leads to a higher mechanical strength in DSRed samples as compared to the undeformed counterparts, however it does not result in a substantial improvement of the material's ductility.
- 1 June 2016
- Published by Elsevier in Journal of Electroanalytical Chemistry
- Vol. 771, 37-44
Anodization of FeAl intermetallic alloys for bandgap tunable nanoporous mixed aluminum-iron oxide
- 1 June 2016
- Published by Elsevier in Journal of Electroanalytical Chemistry
- Vol. 771, 37-44
Anodization of FeAl intermetallic alloys for bandgap tunable nanoporous mixed aluminum-iron oxide
- Open Access
High-Temperature Oxidation of Fe3Al Intermetallic Alloy Prepared by Additive Manufacturing LENS
The isothermal oxidation of Fe-28Al-5Cr (at%) intermetallic alloy microalloyed with Zr and B (2O3 oxide layers. The intensity of their growth indicates that the material lost its resistance to oxidation at 1200 °C. Structural analysis of the thin-walled components’ has not shown intensification of the oxidation process at the joints of additive layers.
Open AccessHigh-Temperature Oxidation of Fe3Al Intermetallic Alloy Prepared by Additive Manufacturing LENS
The isothermal oxidation of Fe-28Al-5Cr (at%) intermetallic alloy microalloyed with Zr and B (2O3 oxide layers. The intensity of their growth indicates that the material lost its resistance to oxidation at 1200 °C. Structural analysis of the thin-walled components’ has not shown intensification of the oxidation process at the joints of additive layers.
- 1 October 2014
- Published by Elsevier in Materials Characterization
- Vol. 96, 196-205
Hot deformation and processing maps of a Fe–Al intermetallic alloy
- 1 October 2014
- Published by Elsevier in Materials Characterization
- Vol. 96, 196-205
Hot deformation and processing maps of a Fe–Al intermetallic alloy
- 1 July 2010
- Published by Elsevier in Intermetallics
- Vol. 18 (7) , 1344-1347
Processing maps for hot working of FeAl-based alloy
- 1 July 2010
- Published by Elsevier in Intermetallics
- Vol. 18 (7) , 1344-1347
Processing maps for hot working of FeAl-based alloy