Mohammadreza Afshar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mohammadreza Afshar has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Hamidreza Najafi
Department of Materials Engineering, Faculty of Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran
6 shared publications - Arman Rabieifar
Department of Materials Engineering, Faculty of Engineering, Karaj Branch, Islamic Azad University, Karaj, Iran
5 shared publications - Said Nategh
Department of Materials Engineering, Faculty of Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran
4 shared publications M. Yari
3 shared publicationsA. Molaei
2 shared publicationsA. Amadeh
School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran, Iran
1 shared publication
Latest Publications
- 5 September 2025
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 14 (5) , 1084-1113
The Effect of Cyclic Hot Corrosion of High-Activity Low-Temperature Pt-Al-7YSZ Coating on Tensile Properties of Gas Turbine Second-Row Blades at 870 °C
- 5 September 2025
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 14 (5) , 1084-1113
The Effect of Cyclic Hot Corrosion of High-Activity Low-Temperature Pt-Al-7YSZ Coating on Tensile Properties of Gas Turbine Second-Row Blades at 870 °C
- 1 November 2023
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 41 (3) , 357-371
The effect of oxide scale and microstructural changes during cyclic hot corrosion on high-temperature tensile properties of Rene-80 superalloy
- 1 November 2023
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 41 (3) , 357-371
The effect of oxide scale and microstructural changes during cyclic hot corrosion on high-temperature tensile properties of Rene-80 superalloy
- Open Access
- 15 May 2023
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 13 (22) , 14899-14913
Investigation of chalcopyrite removal from low-grade molybdenite using response surface methodology and its effect on molybdenum trioxide morphology by roasting
Chalcopyrite removal to enhance the length of MoO 3 fibers.
- 15 May 2023
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 13 (22) , 14899-14913
Open AccessInvestigation of chalcopyrite removal from low-grade molybdenite using response surface methodology and its effect on molybdenum trioxide morphology by roasting
Chalcopyrite removal to enhance the length of MoO 3 fibers.
- 2 January 2023
- Published by Taylor & Francis in Transactions of the Indian Ceramic Society
- Vol. 82 (1) , 21-30
Optimizing Nanostructured Yttria-Stabilized Zirconia Electrophoretic Coatings on MCrAlY Bond-Coated Inconel 738LC Superalloy
In this research study, to apply uniform and homogenous nanostructured yttriastabilized zirconia (YSZ) coatings on the Inconel 738LC with MCrAlY bond-coat, the effect of electrophoretic parameters was evaluated. Two different suspensions of 3YSZ nanoparticles were prepared in acetylacetone and acetone separately, using an iodine dispersant. The electrophoretic deposition was conducted by applying voltages of 20 V, 50 V and 80 V for 3 min on MCrAlY coated Inconel 738LC. The coatings were sintered for 120 min at 900°, 1000° and 1100°C temperature. The results revealed that the non-uniform coating included some cracks and cavities as the applied voltage exceeded the optimal amount. The results also depicted that the YSZ coating prepared in acetylacetone medium with 0.4 g/L iodine dispersant, voltage of 50 V, coating time of 3 min, and sintering temperature of 1000°C was a uniform and crack-free structure. Furthermore, the results showed that a continuous alumina layer was formed during oxidation. GRAPHICAL ABSTRACT
- 2 January 2023
- Published by Taylor & Francis in Transactions of the Indian Ceramic Society
- Vol. 82 (1) , 21-30
Optimizing Nanostructured Yttria-Stabilized Zirconia Electrophoretic Coatings on MCrAlY Bond-Coated Inconel 738LC Superalloy
In this research study, to apply uniform and homogenous nanostructured yttriastabilized zirconia (YSZ) coatings on the Inconel 738LC with MCrAlY bond-coat, the effect of electrophoretic parameters was evaluated. Two different suspensions of 3YSZ nanoparticles were prepared in acetylacetone and acetone separately, using an iodine dispersant. The electrophoretic deposition was conducted by applying voltages of 20 V, 50 V and 80 V for 3 min on MCrAlY coated Inconel 738LC. The coatings were sintered for 120 min at 900°, 1000° and 1100°C temperature. The results revealed that the non-uniform coating included some cracks and cavities as the applied voltage exceeded the optimal amount. The results also depicted that the YSZ coating prepared in acetylacetone medium with 0.4 g/L iodine dispersant, voltage of 50 V, coating time of 3 min, and sintering temperature of 1000°C was a uniform and crack-free structure. Furthermore, the results showed that a continuous alumina layer was formed during oxidation. GRAPHICAL ABSTRACT
- 6 October 2021
- Published by SAGE Publications in Corrosion Engineering, Science and Technology: The International Journal of Corrosion Processes and Corrosion Control
- Vol. 57 (1) , 55-65
The evaluation of oxide scale formation during hot corrosion of Rene-80 superalloy under thermal shock at different dwell times
In this study, the oxide scale formation on the Rene-80 superalloy after hot corrosion under thermal shock has been investigated. The X-ray diffraction (XRD) and field-emission scanning electron microscope (FE-SEM) were used for the phase identification and evaluation of oxide scale, respectively. The hot corrosion test under thermal shock was performed by depositing Na2SO4 salt at the beginning of each cycle on the surface of the specimens. The results showed that hot corrosion occurred intermittently with the basic fluxing mechanism of the oxide scale and re-precipitation of discontinuous and porous oxides. The growth rate of the Cr2O3 layer increased with decreasing the dwell time per cycle and the dissolution of titanium. Decreasing the dwell time in each hot corrosion cycle increased the growth rate of the Cr2O3 layer, the chromium depletion from the substrate/oxide scale interface, the internal oxidation of aluminium, and the internal sulfidation of chromium.
- 6 October 2021
- Published by SAGE Publications in Corrosion Engineering, Science and Technology: The International Journal of Corrosion Processes and Corrosion Control
- Vol. 57 (1) , 55-65
The evaluation of oxide scale formation during hot corrosion of Rene-80 superalloy under thermal shock at different dwell times
In this study, the oxide scale formation on the Rene-80 superalloy after hot corrosion under thermal shock has been investigated. The X-ray diffraction (XRD) and field-emission scanning electron microscope (FE-SEM) were used for the phase identification and evaluation of oxide scale, respectively. The hot corrosion test under thermal shock was performed by depositing Na2SO4 salt at the beginning of each cycle on the surface of the specimens. The results showed that hot corrosion occurred intermittently with the basic fluxing mechanism of the oxide scale and re-precipitation of discontinuous and porous oxides. The growth rate of the Cr2O3 layer increased with decreasing the dwell time per cycle and the dissolution of titanium. Decreasing the dwell time in each hot corrosion cycle increased the growth rate of the Cr2O3 layer, the chromium depletion from the substrate/oxide scale interface, the internal oxidation of aluminium, and the internal sulfidation of chromium.
- 9 November 2020
- Published by Springer Nature in Oxidation of Metals
- Vol. 94 (5-6) , 549-567
The Cyclic Hot Corrosion Behavior of Pt–Al–7%YSZ Coating
- 9 November 2020
- Published by Springer Nature in Oxidation of Metals
- Vol. 94 (5-6) , 549-567
The Cyclic Hot Corrosion Behavior of Pt–Al–7%YSZ Coating
- Open Access
- 1 January 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (1) , 016575
Microstructural evolution and cyclic oxidation of Pt-Al-YSZ coating under thermal shock
In this research, the effect of thermal shock has been investigated on the microstructure and cyclic oxidation of Pt-Al-7%YSZ coating applied on Rene-80 superalloy. The microstructural evaluation and phase identification were performed by field emission scanning electron microscope (FE-SEM) and X-ray diffraction (XRD). The thermal shock test consisted of repeated cycles of rapid cooling between 900 °C and 400 °C. Prior to the thermal shock test, the specimen coated by Pt-electroplating, high-activity low-temperature (HALT) aluminizing and the thermal spray of YSZ ceramic layer. From surface towards the substrate; the coating consisted of 5 layers including: 7% YSZ, PtAl2 + β-(Ni,Pt)Al, β-(Ni,Pt)Al with fine precipitates rich in α-(Cr) and α-(W), precipitate-free β-NiAl, and inter-diffusion zone next to the specimen surface. After the thermal shock test, spallation and delamination have been observed in the YSZ layer. The Pt-Al layer was found in upper and lower parts of the coating with different Pt concentration. Also, the chemical composition of the Pt-Al layer demonstrated the removal of PtAl2 particles and β transformation to both γ and γ′ phases. Degradation of Pt-Al layer occurred by ratcheting the thermally grown oxide (TGO), rumpling, and cavitation. Comparison of weight changes showed that the thermal shock resistance is improved by Pt-Al-7% YSZ coating.
- 1 January 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (1) , 016575
Open AccessMicrostructural evolution and cyclic oxidation of Pt-Al-YSZ coating under thermal shock
In this research, the effect of thermal shock has been investigated on the microstructure and cyclic oxidation of Pt-Al-7%YSZ coating applied on Rene-80 superalloy. The microstructural evaluation and phase identification were performed by field emission scanning electron microscope (FE-SEM) and X-ray diffraction (XRD). The thermal shock test consisted of repeated cycles of rapid cooling between 900 °C and 400 °C. Prior to the thermal shock test, the specimen coated by Pt-electroplating, high-activity low-temperature (HALT) aluminizing and the thermal spray of YSZ ceramic layer. From surface towards the substrate; the coating consisted of 5 layers including: 7% YSZ, PtAl2 + β-(Ni,Pt)Al, β-(Ni,Pt)Al with fine precipitates rich in α-(Cr) and α-(W), precipitate-free β-NiAl, and inter-diffusion zone next to the specimen surface. After the thermal shock test, spallation and delamination have been observed in the YSZ layer. The Pt-Al layer was found in upper and lower parts of the coating with different Pt concentration. Also, the chemical composition of the Pt-Al layer demonstrated the removal of PtAl2 particles and β transformation to both γ and γ′ phases. Degradation of Pt-Al layer occurred by ratcheting the thermally grown oxide (TGO), rumpling, and cavitation. Comparison of weight changes showed that the thermal shock resistance is improved by Pt-Al-7% YSZ coating.
- 11 June 2018
- Published by Springer Nature in Metals and Materials International
- Vol. 25 (1) , 229-237
Comparison Between Vanadium and Niobium Effects on the Mechanical Properties of Intercritically Heat Treated Microalloyed Cast Steels
- 11 June 2018
- Published by Springer Nature in Metals and Materials International
- Vol. 25 (1) , 229-237
Comparison Between Vanadium and Niobium Effects on the Mechanical Properties of Intercritically Heat Treated Microalloyed Cast Steels
- 1 February 2018
- Published by IOP Publishing in Chinese Physics B
- Vol. 27 (2)
Influences of substrate temperature on microstructure and corrosion behavior of APS Ni 50 Ti 25 Al 25 inter-metallic coating
- 1 February 2018
- Published by IOP Publishing in Chinese Physics B
- Vol. 27 (2)
Influences of substrate temperature on microstructure and corrosion behavior of APS Ni 50 Ti 25 Al 25 inter-metallic coating