Arman Rabieifar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Arman Rabieifar has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Hamidreza Najafi
Department of Materials Engineering, Faculty of Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran
5 shared publications - Mohammadreza Afshar
Department of Materials Engineering, Faculty of Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran
5 shared publications - Said Nategh
Department of Materials Engineering, Faculty of Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran
5 shared publications Hamidreza Najafi
Department of Materials Engineering, Science and Research Branch, Islamic Azad University, Sattari Highway, Tehran, Iran
2 shared publications- Hudsa Majidian
Ceramic Department, Materials and Energy Research Center, Karaj, Iran
2 shared publications - Leila Nikzad
Ceramics Department, Materials and Energy Research Center (MERC), Karaj, Iran
2 shared publications
Latest Publications
- 5 September 2025
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 14 (5) , 1084-1113
The Effect of Cyclic Hot Corrosion of High-Activity Low-Temperature Pt-Al-7YSZ Coating on Tensile Properties of Gas Turbine Second-Row Blades at 870 °C
- 5 September 2025
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 14 (5) , 1084-1113
The Effect of Cyclic Hot Corrosion of High-Activity Low-Temperature Pt-Al-7YSZ Coating on Tensile Properties of Gas Turbine Second-Row Blades at 870 °C
- 2 November 2023
- Published by Pleiades Publishing Ltd in Protection of Metals and Physical Chemistry of Surfaces
- Vol. 59 (5) , 946-955
The Microstructural and Chemical Composition Changes in TGO and BC of HALT Pt–Al–APS YSZ Coating After Cyclic Oxidation
In this research, the microstructural and chemical composition changes of thermally grown oxide (TGO) and bond coat (BC) layer were investigated after cyclic oxidation of Pt–Al–YSZ coating at 950°C. First, the Pt–Al layer was coated by the high-activity-low-temperature (HALT) method on the Rene-80 substrate, and then the YSZ top coat (TC) layer was coated by the atmospheric plasma spraying (APS) method on the HALT Pt–Al layer. Cyclic oxidation was performed in ambient air for 50 cycles. After cyclic oxidation, the Pt–Al layer was divided into upper and lower regions. Upward diffusion of Al from the Pt-Al layer to TGO led to the transformation of β to γ′ and γ in the lower region, rumpling in the upper region, and internal oxidation at the interface of the upper and lower region of the Pt–Al layer. The TGO layer included mixed oxides of NiO, Cr2O3, and NiCr2O4, along with discontinuous Al2O3 veins. Depletion of Al from Pt–Al led to the ratcheting of the TGO, the formation of NiAl2O4 at the Pt–Al/TGO interface, and, subsequently, the nucleation of lateral microcracks in the upper region of the Pt–Al. A mechanism for changing the chemical composition of TGO after cyclic oxidation was proposed.
- 2 November 2023
- Published by Pleiades Publishing Ltd in Protection of Metals and Physical Chemistry of Surfaces
- Vol. 59 (5) , 946-955
The Microstructural and Chemical Composition Changes in TGO and BC of HALT Pt–Al–APS YSZ Coating After Cyclic Oxidation
In this research, the microstructural and chemical composition changes of thermally grown oxide (TGO) and bond coat (BC) layer were investigated after cyclic oxidation of Pt–Al–YSZ coating at 950°C. First, the Pt–Al layer was coated by the high-activity-low-temperature (HALT) method on the Rene-80 substrate, and then the YSZ top coat (TC) layer was coated by the atmospheric plasma spraying (APS) method on the HALT Pt–Al layer. Cyclic oxidation was performed in ambient air for 50 cycles. After cyclic oxidation, the Pt–Al layer was divided into upper and lower regions. Upward diffusion of Al from the Pt-Al layer to TGO led to the transformation of β to γ′ and γ in the lower region, rumpling in the upper region, and internal oxidation at the interface of the upper and lower region of the Pt–Al layer. The TGO layer included mixed oxides of NiO, Cr2O3, and NiCr2O4, along with discontinuous Al2O3 veins. Depletion of Al from Pt–Al led to the ratcheting of the TGO, the formation of NiAl2O4 at the Pt–Al/TGO interface, and, subsequently, the nucleation of lateral microcracks in the upper region of the Pt–Al. A mechanism for changing the chemical composition of TGO after cyclic oxidation was proposed.
- 1 November 2023
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 41 (3) , 357-371
The effect of oxide scale and microstructural changes during cyclic hot corrosion on high-temperature tensile properties of Rene-80 superalloy
- 1 November 2023
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 41 (3) , 357-371
The effect of oxide scale and microstructural changes during cyclic hot corrosion on high-temperature tensile properties of Rene-80 superalloy
- 6 October 2021
- Published by SAGE Publications in Corrosion Engineering, Science and Technology: The International Journal of Corrosion Processes and Corrosion Control
- Vol. 57 (1) , 55-65
The evaluation of oxide scale formation during hot corrosion of Rene-80 superalloy under thermal shock at different dwell times
In this study, the oxide scale formation on the Rene-80 superalloy after hot corrosion under thermal shock has been investigated. The X-ray diffraction (XRD) and field-emission scanning electron microscope (FE-SEM) were used for the phase identification and evaluation of oxide scale, respectively. The hot corrosion test under thermal shock was performed by depositing Na2SO4 salt at the beginning of each cycle on the surface of the specimens. The results showed that hot corrosion occurred intermittently with the basic fluxing mechanism of the oxide scale and re-precipitation of discontinuous and porous oxides. The growth rate of the Cr2O3 layer increased with decreasing the dwell time per cycle and the dissolution of titanium. Decreasing the dwell time in each hot corrosion cycle increased the growth rate of the Cr2O3 layer, the chromium depletion from the substrate/oxide scale interface, the internal oxidation of aluminium, and the internal sulfidation of chromium.
- 6 October 2021
- Published by SAGE Publications in Corrosion Engineering, Science and Technology: The International Journal of Corrosion Processes and Corrosion Control
- Vol. 57 (1) , 55-65
The evaluation of oxide scale formation during hot corrosion of Rene-80 superalloy under thermal shock at different dwell times
In this study, the oxide scale formation on the Rene-80 superalloy after hot corrosion under thermal shock has been investigated. The X-ray diffraction (XRD) and field-emission scanning electron microscope (FE-SEM) were used for the phase identification and evaluation of oxide scale, respectively. The hot corrosion test under thermal shock was performed by depositing Na2SO4 salt at the beginning of each cycle on the surface of the specimens. The results showed that hot corrosion occurred intermittently with the basic fluxing mechanism of the oxide scale and re-precipitation of discontinuous and porous oxides. The growth rate of the Cr2O3 layer increased with decreasing the dwell time per cycle and the dissolution of titanium. Decreasing the dwell time in each hot corrosion cycle increased the growth rate of the Cr2O3 layer, the chromium depletion from the substrate/oxide scale interface, the internal oxidation of aluminium, and the internal sulfidation of chromium.
- 9 November 2020
- Published by Springer Nature in Oxidation of Metals
- Vol. 94 (5-6) , 549-567
The Cyclic Hot Corrosion Behavior of Pt–Al–7%YSZ Coating
- 9 November 2020
- Published by Springer Nature in Oxidation of Metals
- Vol. 94 (5-6) , 549-567
The Cyclic Hot Corrosion Behavior of Pt–Al–7%YSZ Coating
- Open Access
- 1 January 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (1) , 016575
Microstructural evolution and cyclic oxidation of Pt-Al-YSZ coating under thermal shock
In this research, the effect of thermal shock has been investigated on the microstructure and cyclic oxidation of Pt-Al-7%YSZ coating applied on Rene-80 superalloy. The microstructural evaluation and phase identification were performed by field emission scanning electron microscope (FE-SEM) and X-ray diffraction (XRD). The thermal shock test consisted of repeated cycles of rapid cooling between 900 °C and 400 °C. Prior to the thermal shock test, the specimen coated by Pt-electroplating, high-activity low-temperature (HALT) aluminizing and the thermal spray of YSZ ceramic layer. From surface towards the substrate; the coating consisted of 5 layers including: 7% YSZ, PtAl2 + β-(Ni,Pt)Al, β-(Ni,Pt)Al with fine precipitates rich in α-(Cr) and α-(W), precipitate-free β-NiAl, and inter-diffusion zone next to the specimen surface. After the thermal shock test, spallation and delamination have been observed in the YSZ layer. The Pt-Al layer was found in upper and lower parts of the coating with different Pt concentration. Also, the chemical composition of the Pt-Al layer demonstrated the removal of PtAl2 particles and β transformation to both γ and γ′ phases. Degradation of Pt-Al layer occurred by ratcheting the thermally grown oxide (TGO), rumpling, and cavitation. Comparison of weight changes showed that the thermal shock resistance is improved by Pt-Al-7% YSZ coating.
- 1 January 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (1) , 016575
Open AccessMicrostructural evolution and cyclic oxidation of Pt-Al-YSZ coating under thermal shock
In this research, the effect of thermal shock has been investigated on the microstructure and cyclic oxidation of Pt-Al-7%YSZ coating applied on Rene-80 superalloy. The microstructural evaluation and phase identification were performed by field emission scanning electron microscope (FE-SEM) and X-ray diffraction (XRD). The thermal shock test consisted of repeated cycles of rapid cooling between 900 °C and 400 °C. Prior to the thermal shock test, the specimen coated by Pt-electroplating, high-activity low-temperature (HALT) aluminizing and the thermal spray of YSZ ceramic layer. From surface towards the substrate; the coating consisted of 5 layers including: 7% YSZ, PtAl2 + β-(Ni,Pt)Al, β-(Ni,Pt)Al with fine precipitates rich in α-(Cr) and α-(W), precipitate-free β-NiAl, and inter-diffusion zone next to the specimen surface. After the thermal shock test, spallation and delamination have been observed in the YSZ layer. The Pt-Al layer was found in upper and lower parts of the coating with different Pt concentration. Also, the chemical composition of the Pt-Al layer demonstrated the removal of PtAl2 particles and β transformation to both γ and γ′ phases. Degradation of Pt-Al layer occurred by ratcheting the thermally grown oxide (TGO), rumpling, and cavitation. Comparison of weight changes showed that the thermal shock resistance is improved by Pt-Al-7% YSZ coating.