William Scott Marshall
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
William Scott Marshall has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
- Iain R. Dixon
National High Magnetic Field Laboratory, Florida State University, Tallahassee, FL, USA
5 shared publications - Andrey Vladimir Gavrilin
National High Magnetic Field Laboratory, Tallahassee, FL, USA
3 shared publications - David C. Larbalestier
Florida State University
3 shared publications - Hongyu Bai
National High Magnetic Field Laboratory, Florida State University, Tallahassee, FL, USA
2 shared publications - Jun Lu
Magnetic Science and Technology National High Magnetic Field Laboratory Tallahassee Florida USA
2 shared publications - Kwang Lok Kim
National High Magnetic Field Laboratory, Tallahassee, FL, USA
2 shared publications
Latest Publications
- 4 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
Report on Over 25 000 Cycles Fatigue Test Results of a REBCO HTS Coil and Crossover Joint in a 7 T Background Magnetic Field at 4.2 K
This study presents experimental results on the fatigue characteristics of a REBCO coil and crossover joint, aiming to determine whether they can withstand cyclic loading up to the condition of the 40 T superconducting magnet's design fatigue limit. A pair of REBCO coils were wound with SP (SuperPower) 1013, using copper and stainless steel tape as co-winding materials. The crossover sample, designed to the 40 T superconducting magnet baseline specifications and composed of four Bi2223 (Sumitomo Type H) tape conductors soldered to a stainless steel foil, was mounted to the outermost turn of the REBCO coil. Both the coil and crossover were subjected to cyclic loading by ramping the current up and down in a 7 T background magnetic (BM) field at 4.2 K, with over 25,000 cycles applied. The electromagnetic strain between the outermost turn of the REBCO coil and the crossover joint was estimated numerically, considering the screening current distribution.
- 4 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
Report on Over 25 000 Cycles Fatigue Test Results of a REBCO HTS Coil and Crossover Joint in a 7 T Background Magnetic Field at 4.2 K
This study presents experimental results on the fatigue characteristics of a REBCO coil and crossover joint, aiming to determine whether they can withstand cyclic loading up to the condition of the 40 T superconducting magnet's design fatigue limit. A pair of REBCO coils were wound with SP (SuperPower) 1013, using copper and stainless steel tape as co-winding materials. The crossover sample, designed to the 40 T superconducting magnet baseline specifications and composed of four Bi2223 (Sumitomo Type H) tape conductors soldered to a stainless steel foil, was mounted to the outermost turn of the REBCO coil. Both the coil and crossover were subjected to cyclic loading by ramping the current up and down in a 7 T background magnetic (BM) field at 4.2 K, with over 25,000 cycles applied. The electromagnetic strain between the outermost turn of the REBCO coil and the crossover joint was estimated numerically, considering the screening current distribution.
- 15 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
REBCO Soldered Lap Joint Resistance Versus Length and Tape Manufacturer
REBCO high-temperature superconductor tapes are made in piece lengths too short for many complete devices such as high-field solenoid magnets, cables, fault limiters, etc. In-line splices are required, and soldering is the preferred method of fabrication. The resistance and contact resistivity of such lap joints is a topic of ongoing investigation. To date it is well understood that the resistance of a soldered REBCO lap joint depends inversely upon the length of the joint in the range practical for devices. It is also well understood that the dominant contributor to the resistance of a lap joint is the interface resistance between the REBCO conductor and its applied silver coating. This property could differ by manufacturer. In this study, a direct comparison is made by fabricating lap joints with REBCO tape from several manufacturers in a range of lengths and measuring the resistance.
- 15 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
REBCO Soldered Lap Joint Resistance Versus Length and Tape Manufacturer
REBCO high-temperature superconductor tapes are made in piece lengths too short for many complete devices such as high-field solenoid magnets, cables, fault limiters, etc. In-line splices are required, and soldering is the preferred method of fabrication. The resistance and contact resistivity of such lap joints is a topic of ongoing investigation. To date it is well understood that the resistance of a soldered REBCO lap joint depends inversely upon the length of the joint in the range practical for devices. It is also well understood that the dominant contributor to the resistance of a lap joint is the interface resistance between the REBCO conductor and its applied silver coating. This property could differ by manufacturer. In this study, a direct comparison is made by fabricating lap joints with REBCO tape from several manufacturers in a range of lengths and measuring the resistance.
- 6 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-4
Comparison Between Results of Quench Simulation and Tests of a 13 T REBCO Coil in a Strong Background Magnetic Field
In the framework of the 40 T all-superconducting magnet project at the National High Magnetic Field laboratory, improvements have been made in a quench model and the quench code that has been constructed to simulate the behavior of a magnet consisting of an HTS inner coil set with an LTS background field. The quench model, initially developed for the NHMFL 32 T magnet project, incorporates additional details of the REBCO conductor on a localized level. These include nonuniform magnetic field distribution across each conductor turn and deformation of the turns due to screening currents which affects the true field angle applied to the conductor's a-b plane. Detailed measurements of the test coil's conductors have also been made to improve the simulations. These include the slope of the a-b plane using X-ray techniques and IC (B, θ, T) of each conductor length using torque magnetometry. The test coil generating a field up to 13 T is an insulated, two-in-hand REBCO coil with twelve modules. Deliberate quench tests were performed with it in self-field and with a 11.4 T background field. The results and discussion of the comparisons are presented.
- 6 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-4
Comparison Between Results of Quench Simulation and Tests of a 13 T REBCO Coil in a Strong Background Magnetic Field
In the framework of the 40 T all-superconducting magnet project at the National High Magnetic Field laboratory, improvements have been made in a quench model and the quench code that has been constructed to simulate the behavior of a magnet consisting of an HTS inner coil set with an LTS background field. The quench model, initially developed for the NHMFL 32 T magnet project, incorporates additional details of the REBCO conductor on a localized level. These include nonuniform magnetic field distribution across each conductor turn and deformation of the turns due to screening currents which affects the true field angle applied to the conductor's a-b plane. Detailed measurements of the test coil's conductors have also been made to improve the simulations. These include the slope of the a-b plane using X-ray techniques and IC (B, θ, T) of each conductor length using torque magnetometry. The test coil generating a field up to 13 T is an insulated, two-in-hand REBCO coil with twelve modules. Deliberate quench tests were performed with it in self-field and with a 11.4 T background field. The results and discussion of the comparisons are presented.
- 7 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (6) , 1-4
Lap Joint Resistivity and Crossover Resistance of REBCO Conductors and Coils
During the NHMFL 32 T magnet project, a program to develop a reliable method for making soldered lap joints between REBCO tape conductors was initiated. A standard process was adopted during the program, and then applied during coil fabrication and for quality control (QC) of incoming conductor. For each unique REBCO conductor piece procured for the 32 T project, a lap solder joint was made using the standard process and tested for resistance in liquid nitrogen. A total of 211 lap joints were made and tested. For the NHMFL 40 T magnet project, a similar study was performed using the same standard process on conductors procured for test coils. A total of 38 lap joints were made and tested. Results from both data sets are reported, and compared with findings from the initial study and published findings by others. In the stacked double-pancake construction adopted by the NHMFL for REBCO coils, each double-pancake is connected in series to adjacent modules with a crossover connection, made from an assembly of several REBCO tapes placed in parallel and soldered across the terminal ends of each adjacent module. Resistances of the crossovers in a 32 T test coil and from test articles and test coils made during the 40 T project, are reported here. The resistivity of the crossovers is estimated and compared with the findings from the lap joint measurements.
- 7 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (6) , 1-4
Lap Joint Resistivity and Crossover Resistance of REBCO Conductors and Coils
During the NHMFL 32 T magnet project, a program to develop a reliable method for making soldered lap joints between REBCO tape conductors was initiated. A standard process was adopted during the program, and then applied during coil fabrication and for quality control (QC) of incoming conductor. For each unique REBCO conductor piece procured for the 32 T project, a lap solder joint was made using the standard process and tested for resistance in liquid nitrogen. A total of 211 lap joints were made and tested. For the NHMFL 40 T magnet project, a similar study was performed using the same standard process on conductors procured for test coils. A total of 38 lap joints were made and tested. Results from both data sets are reported, and compared with findings from the initial study and published findings by others. In the stacked double-pancake construction adopted by the NHMFL for REBCO coils, each double-pancake is connected in series to adjacent modules with a crossover connection, made from an assembly of several REBCO tapes placed in parallel and soldered across the terminal ends of each adjacent module. Resistances of the crossovers in a 32 T test coil and from test articles and test coils made during the 40 T project, are reported here. The resistivity of the crossovers is estimated and compared with the findings from the lap joint measurements.
- 17 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (5) , 1-7
Quench and Stability Modelling of a Metal-Insulation Multi-Double-Pancake High-Temperature-Superconducting Coil
The most detailed, first-principle simulation model of a quench in a high-temperature superconducting metal-insulation multi-module/multi-double-pancake coil, wound with a REBCO coated superconductor/tape and normal-metal tape (co-wind), was developed. It enables one to simulate a normal zone propagation, or non-propagation, in the subtle multi-turn structure of the coil's pancakes due to the inductive coupling and transverse electric contact between all the REBCO turns and co-wind turns along with the external circuit and active and passive quench protection systems. In doing so, the multi-module coil's structure is represented as a “rectilinear equivalent” electric circuit, a branched multi-decker multi-rectangle planar grid, which facilitates the mathematical formulation, using the standard electric circuit differential equations and the Kirchhoff's rules. The transient non-linear comprehensive heat conduction equations are employed to model the thermal part of the phenomenon at the same level of detail. All this turns the model into an effective design tool for metal-insulated, -stabilized and/or -reinforced multi-module coils. A parametric study of quench in a 6-module no-insulation (NI) test coil, using a stainless-steel thin co-wind, was conducted to identify the possibilities of the model. The profound effect of the transverse contact resistivity on an NI-coil quench behavior is confirmed and detailed.
- 17 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (5) , 1-7
Quench and Stability Modelling of a Metal-Insulation Multi-Double-Pancake High-Temperature-Superconducting Coil
The most detailed, first-principle simulation model of a quench in a high-temperature superconducting metal-insulation multi-module/multi-double-pancake coil, wound with a REBCO coated superconductor/tape and normal-metal tape (co-wind), was developed. It enables one to simulate a normal zone propagation, or non-propagation, in the subtle multi-turn structure of the coil's pancakes due to the inductive coupling and transverse electric contact between all the REBCO turns and co-wind turns along with the external circuit and active and passive quench protection systems. In doing so, the multi-module coil's structure is represented as a “rectilinear equivalent” electric circuit, a branched multi-decker multi-rectangle planar grid, which facilitates the mathematical formulation, using the standard electric circuit differential equations and the Kirchhoff's rules. The transient non-linear comprehensive heat conduction equations are employed to model the thermal part of the phenomenon at the same level of detail. All this turns the model into an effective design tool for metal-insulated, -stabilized and/or -reinforced multi-module coils. A parametric study of quench in a 6-module no-insulation (NI) test coil, using a stainless-steel thin co-wind, was conducted to identify the possibilities of the model. The profound effect of the transverse contact resistivity on an NI-coil quench behavior is confirmed and detailed.
- 30 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Composite Mechanical Properties of Coils Made With Nickel-Alloy Laminated Bi-2223 Conductors
High-temperature superconducting magnet coils made with Sumitomo Type HT-NX are complex composite structures composed of Bi-2223 conductor filaments, silver matrix, solder, nickel-alloy laminations, polymer insulation, and epoxy or wax. The mechanical properties of these composites are required inputs to a correct stress analysis. Measurements of the desired properties are performed on representative model test specimens. Mechanical test specimens composed of several layers of insulated conductor are prepared by cutting to length, stacking and epoxy impregnation. Mechanical tests are performed in liquid nitrogen and liquid helium. Elastic constants are found from tensile strain measurements in the conductor longitudinal, or coil hoop, direction and from compressive strain measurements in the conductor transverse, or coil radial and axial directions.
- 30 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Composite Mechanical Properties of Coils Made With Nickel-Alloy Laminated Bi-2223 Conductors
High-temperature superconducting magnet coils made with Sumitomo Type HT-NX are complex composite structures composed of Bi-2223 conductor filaments, silver matrix, solder, nickel-alloy laminations, polymer insulation, and epoxy or wax. The mechanical properties of these composites are required inputs to a correct stress analysis. Measurements of the desired properties are performed on representative model test specimens. Mechanical test specimens composed of several layers of insulated conductor are prepared by cutting to length, stacking and epoxy impregnation. Mechanical tests are performed in liquid nitrogen and liquid helium. Elastic constants are found from tensile strain measurements in the conductor longitudinal, or coil hoop, direction and from compressive strain measurements in the conductor transverse, or coil radial and axial directions.
- 27 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-5
The 40 T Superconducting Magnet Project at the National High Magnetic Field Laboratory
- 27 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-5
The 40 T Superconducting Magnet Project at the National High Magnetic Field Laboratory
- 4 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-4
Design of Strain-Limited Bi-2223 Insert Coils for High-Field Magnets
High field solenoid coils made with HTS conductors are limited primarily by total strain, and then by critical current. A detailed accounting of all the sources of mechanical strain on a coil is an essential part of the design. Those sources include winding tension, bending about the coil axis, bending to form the layer transition, compression from overbanding, differential thermal contraction, magnetic hoop strain in the radial and axial directions and thermal expansion from quenches. A design example for a high-field insert coil made with Sumitomo Type HT-NX Bi-2223 conductor is presented, with each of the relevant strains computed explicitly
- 4 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-4
Design of Strain-Limited Bi-2223 Insert Coils for High-Field Magnets
High field solenoid coils made with HTS conductors are limited primarily by total strain, and then by critical current. A detailed accounting of all the sources of mechanical strain on a coil is an essential part of the design. Those sources include winding tension, bending about the coil axis, bending to form the layer transition, compression from overbanding, differential thermal contraction, magnetic hoop strain in the radial and axial directions and thermal expansion from quenches. A design example for a high-field insert coil made with Sumitomo Type HT-NX Bi-2223 conductor is presented, with each of the relevant strains computed explicitly
- Open Access
- 16 January 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 27 (4) , 1-5
Bi-2223 Test Coils for High-Resolution NMR Magnets
Recently, significant improvement in the strain tolerance of Bi-2223 conductor has been achieved by lamination with high strength nickel alloy. The conductor, supplied by Sumitomo Electric and designated Type HT-NX, is now commercially available in lengths sufficient for manufacture of high-homogeneity solenoids. A program to fully exploit the improved conductor properties is now underway at the National High Magnetic Field Laboratory (NHMFL). Five coils are being made, the last of which is to demonstrate an NMR measurement approaching 1 GHz and 1 ppm over 10-mm volume. In so doing, we expect to demonstrate critical current fraction, and strain similar to that expected in 30-T NMR magnets. The coils will be tested inside an existing 16 Tesla large-bore background magnet at the NHMFL. The design of the NMR demonstration coil is presented first, with expected values for field, homogeneity, and strain given. A technology development program is then outlined, which includes fabrication of four test coils to test various design features, develop fabrication tooling, and train personnel.
- 16 January 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 27 (4) , 1-5
Open AccessBi-2223 Test Coils for High-Resolution NMR Magnets
Recently, significant improvement in the strain tolerance of Bi-2223 conductor has been achieved by lamination with high strength nickel alloy. The conductor, supplied by Sumitomo Electric and designated Type HT-NX, is now commercially available in lengths sufficient for manufacture of high-homogeneity solenoids. A program to fully exploit the improved conductor properties is now underway at the National High Magnetic Field Laboratory (NHMFL). Five coils are being made, the last of which is to demonstrate an NMR measurement approaching 1 GHz and 1 ppm over 10-mm volume. In so doing, we expect to demonstrate critical current fraction, and strain similar to that expected in 30-T NMR magnets. The coils will be tested inside an existing 16 Tesla large-bore background magnet at the NHMFL. The design of the NMR demonstration coil is presented first, with expected values for field, homogeneity, and strain given. A technology development program is then outlined, which includes fabrication of four test coils to test various design features, develop fabrication tooling, and train personnel.
- 27 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 25 (3) , 1-4
Fabrication of HTS Conductor Stacks for 20-kA Binary Current Leads for MagLab Series-Connected Hybrid and HFML Nijmegen Hybrid Magnets
The MagLab series-connected hybrid and the HFML Nijmegen hybrid outer superconducting coils each require a pair of binary current leads, comprised of a nitrogen vapor-cooled resistive section and a high-temperature superconducting (HTS) section, configured to minimize the heat load to the coils. The HTS sections of both pairs of leads are made with stacked and soldered Bi-2223 tapes supplied by Sumitomo. The MagLab fabricated and tested the tape stacks for both programs. The procedures and apparatus for fabricating the stacks and making the critical current measurements are described. Critical current and n-value measurement results are reported.
- 27 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 25 (3) , 1-4
Fabrication of HTS Conductor Stacks for 20-kA Binary Current Leads for MagLab Series-Connected Hybrid and HFML Nijmegen Hybrid Magnets
The MagLab series-connected hybrid and the HFML Nijmegen hybrid outer superconducting coils each require a pair of binary current leads, comprised of a nitrogen vapor-cooled resistive section and a high-temperature superconducting (HTS) section, configured to minimize the heat load to the coils. The HTS sections of both pairs of leads are made with stacked and soldered Bi-2223 tapes supplied by Sumitomo. The MagLab fabricated and tested the tape stacks for both programs. The procedures and apparatus for fabricating the stacks and making the critical current measurements are described. Critical current and n-value measurement results are reported.