Wei Cao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wei Cao has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
Changyu Shen
State Key Laboratory of Structural Analysis, Optimization and CAE Software for Industrial Equipment, National Engineering Research Center for Advanced Polymer Processing Technology Zhengzhou University Zhengzhou China
8 shared publicationsShixun Zhang
5 shared publicationsQian Li
Engineering Research Center of Mold and Die Zhengzhou University Zhengzhou Henan Province China
3 shared publicationsHaimei Li
National Engineering Research Center of Mold & Die Zhengzhou University Zhengzhou Henan 450002 China
2 shared publicationsTao Wang
Beijing Institute of Aeronautical Materials Beijing 100095 China
2 shared publications- Yaming Wang
Zhengzhou University
2 shared publications
Latest Publications
- 1 April 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (4)
Theory construction and computation for polymer film melt stretching by modified Leonov model
Polymer film melt stretching exhibits a unique stress–strain behavior, featuring a stress plateau followed by a sudden increase with increasing the strain. This phenomenon poses a challenge to conventional melt-extension theories and methods. To address this, we derive a simplified flow theory according to the symmetric characteristics of thin melt-stretching, and propose a modified multi-mode Leonov model (m-Leonov) that accounts for molecular orientation effects, a crucial factor in accurately simulating the process. In order to improve the computational efficiency, an iterative algorithm was developed to decouple the interdependence between governing and constitutive equations. The computational results reveal that the viscoelastic nature of the film contributes to a delay in the transformation of stretching forces, leading to the observed stress plateau. Significantly, our m-Leonov model successfully predicts both the plateau and the subsequent abrupt increase in stress, across various temperatures and stretching rates. These simulations closely agree with experimental data, underlining the robustness of our approach. Our findings would enhance the understanding of rheological complexities in film stretching, offering potential applications in various materials and polymer processing.
- 1 April 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (4)
Theory construction and computation for polymer film melt stretching by modified Leonov model
Polymer film melt stretching exhibits a unique stress–strain behavior, featuring a stress plateau followed by a sudden increase with increasing the strain. This phenomenon poses a challenge to conventional melt-extension theories and methods. To address this, we derive a simplified flow theory according to the symmetric characteristics of thin melt-stretching, and propose a modified multi-mode Leonov model (m-Leonov) that accounts for molecular orientation effects, a crucial factor in accurately simulating the process. In order to improve the computational efficiency, an iterative algorithm was developed to decouple the interdependence between governing and constitutive equations. The computational results reveal that the viscoelastic nature of the film contributes to a delay in the transformation of stretching forces, leading to the observed stress plateau. Significantly, our m-Leonov model successfully predicts both the plateau and the subsequent abrupt increase in stress, across various temperatures and stretching rates. These simulations closely agree with experimental data, underlining the robustness of our approach. Our findings would enhance the understanding of rheological complexities in film stretching, offering potential applications in various materials and polymer processing.
- 10 November 2023
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (1) , 170-183
Study of overflow effects on flow‐induced stress in injection molding
Overflow is usually used to keep fluid continuously flowing to avoid the fluid from changing flow direction and subsequently inducing large stresses. To explore the mechanism of flow‐induced stress evolution, a flow model was established in terms of compressible, non‐isothermal, and viscoelastic flow. Based on the Leonov model and the mid‐plane approach, a pseudo‐Poisson type equation for pressure was derived to decouple the interdependence between velocity and pressure. To improve computational efficiency, a numerical approach involving double iterations was proposed to solve the flow problem. Two kinds of mold cavities, with and without overflow, were designed and manufactured. Molding experiments were conducted, and corresponding simulations based on the proposed model and algorithm were performed. The results show that the simulated contours of flow‐induced stress are in good agreement with the photoelastic streaks. The use of overflow can significantly reduce flow‐induced stresses. If the slot thickness is set to a proper value, the flow‐induced stress can be reduced by more than 80%. On the other hand, a slot that is too thick does not have significant reducing effects. Therefore, using overflow to reduce flow‐induced stresses during transparent part production is a promising approach if the material cost is worthy of the quality. Highlights: A double iteration method is proposed for viscoelastic flow problem. Overflow can reduce the stress as much as 80% if the dimension is properly set. The simulated stress streaks are in good agreement with photoelasticities.
- 10 November 2023
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (1) , 170-183
Study of overflow effects on flow‐induced stress in injection molding
Overflow is usually used to keep fluid continuously flowing to avoid the fluid from changing flow direction and subsequently inducing large stresses. To explore the mechanism of flow‐induced stress evolution, a flow model was established in terms of compressible, non‐isothermal, and viscoelastic flow. Based on the Leonov model and the mid‐plane approach, a pseudo‐Poisson type equation for pressure was derived to decouple the interdependence between velocity and pressure. To improve computational efficiency, a numerical approach involving double iterations was proposed to solve the flow problem. Two kinds of mold cavities, with and without overflow, were designed and manufactured. Molding experiments were conducted, and corresponding simulations based on the proposed model and algorithm were performed. The results show that the simulated contours of flow‐induced stress are in good agreement with the photoelastic streaks. The use of overflow can significantly reduce flow‐induced stresses. If the slot thickness is set to a proper value, the flow‐induced stress can be reduced by more than 80%. On the other hand, a slot that is too thick does not have significant reducing effects. Therefore, using overflow to reduce flow‐induced stresses during transparent part production is a promising approach if the material cost is worthy of the quality. Highlights: A double iteration method is proposed for viscoelastic flow problem. Overflow can reduce the stress as much as 80% if the dimension is properly set. The simulated stress streaks are in good agreement with photoelasticities.
- 8 February 2019
- Published by Wiley in Polymer Engineering & Science
- Vol. 59 (s2) , E397-E405
3D Viscoelastic Simulation of Jetting in Injection Molding
A three‐dimensional model and algorithm were proposed to simulate the jetting phenomenon in injection molding. The Giesekus model was employed to describe the viscoelastic behavior of the incompressible, non‐isothermal polymer flow, and the volume of filling method was used to track the jetting free surface and advancing melt front. The governing and constitutive equations were discretized by finite volume method. To improve the precision and stability of the numerical method, a modified pressure implicit with splitting of operator algorithm was proposed to solve the pseudo Navier–Stokes problem, and an iterative scheme was constructed to determine the solution of the coupled nonlinear equations. Numerical results showed this method successfully predicted the snake‐like flow in thin‐wall cavities and buckling flow in thick‐wall cavities. The viscoelastic characteristics of polymer influenced the reptile swing frequency and amplitude. Finally, a suitable nonlinear parameter in the Giesekus model improved the precision of simulation. POLYM. ENG. SCI., 59:E397–E405, 2019. © 2019 Society of Plastics Engineers
- 8 February 2019
- Published by Wiley in Polymer Engineering & Science
- Vol. 59 (s2) , E397-E405
3D Viscoelastic Simulation of Jetting in Injection Molding
A three‐dimensional model and algorithm were proposed to simulate the jetting phenomenon in injection molding. The Giesekus model was employed to describe the viscoelastic behavior of the incompressible, non‐isothermal polymer flow, and the volume of filling method was used to track the jetting free surface and advancing melt front. The governing and constitutive equations were discretized by finite volume method. To improve the precision and stability of the numerical method, a modified pressure implicit with splitting of operator algorithm was proposed to solve the pseudo Navier–Stokes problem, and an iterative scheme was constructed to determine the solution of the coupled nonlinear equations. Numerical results showed this method successfully predicted the snake‐like flow in thin‐wall cavities and buckling flow in thick‐wall cavities. The viscoelastic characteristics of polymer influenced the reptile swing frequency and amplitude. Finally, a suitable nonlinear parameter in the Giesekus model improved the precision of simulation. POLYM. ENG. SCI., 59:E397–E405, 2019. © 2019 Society of Plastics Engineers
- Open Access
Simulation of Jetting in Injection Molding Using a Finite Volume Method
In order to predict the jetting and the subsequent buckling flow more accurately, a three dimensional melt flow model was established on a viscous, incompressible, and non-isothermal fluid, and a control volume-based finite volume method was employed to discretize the governing equations. A two-fold iterative method was proposed to decouple the dependence among pressure, velocity, and temperature so as to reduce the computation and improve the numerical stability. Based on the proposed theoretical model and numerical method, a program code was developed to simulate melt front progress and flow fields. The numerical simulations for different injection speeds, melt temperatures, and gate locations were carried out to explore the jetting mechanism. The results indicate the filling pattern depends on the competition between inertial and viscous forces. When inertial force exceeds the viscous force jetting occurs, then it changes to a buckling flow as the viscous force competes over the inertial force. Once the melt contacts with the mold wall, the melt filling switches to conventional sequential filling mode. Numerical results also indicate jetting length increases with injection speed but changes little with melt temperature. The reasonable agreements between simulated and experimental jetting length and buckling frequency imply the proposed method is valid for jetting simulation.
Open AccessSimulation of Jetting in Injection Molding Using a Finite Volume Method
In order to predict the jetting and the subsequent buckling flow more accurately, a three dimensional melt flow model was established on a viscous, incompressible, and non-isothermal fluid, and a control volume-based finite volume method was employed to discretize the governing equations. A two-fold iterative method was proposed to decouple the dependence among pressure, velocity, and temperature so as to reduce the computation and improve the numerical stability. Based on the proposed theoretical model and numerical method, a program code was developed to simulate melt front progress and flow fields. The numerical simulations for different injection speeds, melt temperatures, and gate locations were carried out to explore the jetting mechanism. The results indicate the filling pattern depends on the competition between inertial and viscous forces. When inertial force exceeds the viscous force jetting occurs, then it changes to a buckling flow as the viscous force competes over the inertial force. Once the melt contacts with the mold wall, the melt filling switches to conventional sequential filling mode. Numerical results also indicate jetting length increases with injection speed but changes little with melt temperature. The reasonable agreements between simulated and experimental jetting length and buckling frequency imply the proposed method is valid for jetting simulation.
- 12 December 2015
- Published by Wiley in Polymer Engineering & Science
- Vol. 56 (3) , 287-298
Numerical simulation for flow‐induced stress in injection/compression molding
Flow‐induced stress in compression stage is complex because compression flow combines both shear flow and extensional flow characters and involves the boundary change in melt front and compressing directions. To describe this kind of flow effectively, the theoretical model was established in terms of three‐dimensional compressible and viscoelastic fluid, and the material derivative which includes mesh moving velocity was introduced to modify the convective terms in governing and constitutive equations based on Arbitrary Lagrangian Eulerian description. The corresponding variational equations were derived via Gauss formula and the finite element method was used to discretize the flow variables with mixed elements. In order to decouple the interdependence of velocity, stress, and temperature, a new approach involves twofold iterations was proposed to solve nonlinear flow problem. A new mesh updating scheme was presented to keep consistent with compressed regions. Numerical results indicate the compression can reduce the flow‐induced stress significantly compared to conventional injection molding, increase compressing velocity enlarges flow‐induced stress, and high temperature decreases flow‐induced stress. The proposed method was verified by photoelastic pictures and measured pressures and temperatures during molding. POLYM. ENG. SCI., 56:287–298, 2016. © 2015 Society of Plastics Engineers
- 12 December 2015
- Published by Wiley in Polymer Engineering & Science
- Vol. 56 (3) , 287-298
Numerical simulation for flow‐induced stress in injection/compression molding
Flow‐induced stress in compression stage is complex because compression flow combines both shear flow and extensional flow characters and involves the boundary change in melt front and compressing directions. To describe this kind of flow effectively, the theoretical model was established in terms of three‐dimensional compressible and viscoelastic fluid, and the material derivative which includes mesh moving velocity was introduced to modify the convective terms in governing and constitutive equations based on Arbitrary Lagrangian Eulerian description. The corresponding variational equations were derived via Gauss formula and the finite element method was used to discretize the flow variables with mixed elements. In order to decouple the interdependence of velocity, stress, and temperature, a new approach involves twofold iterations was proposed to solve nonlinear flow problem. A new mesh updating scheme was presented to keep consistent with compressed regions. Numerical results indicate the compression can reduce the flow‐induced stress significantly compared to conventional injection molding, increase compressing velocity enlarges flow‐induced stress, and high temperature decreases flow‐induced stress. The proposed method was verified by photoelastic pictures and measured pressures and temperatures during molding. POLYM. ENG. SCI., 56:287–298, 2016. © 2015 Society of Plastics Engineers
- 18 April 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (29)
Evaluation of typical rheological models fitting for polycarbonate squeeze flow
High viscous polycarbonate melt exhibits some special rheological characters different from generalized Newtonian fluid during squeezing. It is necessary to evaluate whether the typical rheological models are suitable for polycarbonate squeeze. To avoid the difficult of measuring the inner melt rheological behavior directly, this study presents a method of measuring the compressing force applied on the upper disc of the rheometer to reveal the melt rheology indirectly. The finite difference method (FDM) was employed to discretize the governing equations and constitutive equations established on cylinder coordinate system and to simulate the compressing force. The experiments were carried out under four temperatures and three compressing velocities to test the validations of Leonov, Phan‐Thien–Tanner (PTT), eXtended Pom‐Pom (XPP), and Cross Williams‐Landel‐Ferry (Cross‐WLF) models. The experimental results show the unique character of compressing force evolution as ‘steep—steady—steep—steady’ pattern. Comparison between experiments and simulations reveals that both viscoelastic and viscous models can predict the two steady regions correctly, but only viscoelastic models can simulate the steep increase and decrease of the compressing force. Among the evaluated viscoelastic models, XPP is the most suitable to describe polycarbonate melt compression flow. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42279.
- 18 April 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (29)
Evaluation of typical rheological models fitting for polycarbonate squeeze flow
High viscous polycarbonate melt exhibits some special rheological characters different from generalized Newtonian fluid during squeezing. It is necessary to evaluate whether the typical rheological models are suitable for polycarbonate squeeze. To avoid the difficult of measuring the inner melt rheological behavior directly, this study presents a method of measuring the compressing force applied on the upper disc of the rheometer to reveal the melt rheology indirectly. The finite difference method (FDM) was employed to discretize the governing equations and constitutive equations established on cylinder coordinate system and to simulate the compressing force. The experiments were carried out under four temperatures and three compressing velocities to test the validations of Leonov, Phan‐Thien–Tanner (PTT), eXtended Pom‐Pom (XPP), and Cross Williams‐Landel‐Ferry (Cross‐WLF) models. The experimental results show the unique character of compressing force evolution as ‘steep—steady—steep—steady’ pattern. Comparison between experiments and simulations reveals that both viscoelastic and viscous models can predict the two steady regions correctly, but only viscoelastic models can simulate the steep increase and decrease of the compressing force. Among the evaluated viscoelastic models, XPP is the most suitable to describe polycarbonate melt compression flow. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42279.
- 21 September 2011
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 19 (8) , 085003
Model and simulation for melt flow in micro-injection molding based on the PTT model
Unsteady viscoelastic flows were studied using the finite element method in this work. The Phan-Thien–Tanner (PTT) model was used to represent the rheological behavior of viscoelastic fluids. To effectively describe the microscale effects, the slip boundary condition and surface tension were added to the mathematical model for melt flow in micro-injection molding. The new variational equation of pressure, including the viscoelastic parameters and slip boundary condition, was generalized using integration by parts. A computer code based on the finite element method and finite difference method was developed to solve the melt flow problem. Numerical simulation revealed that the melt viscoelasticity plays an important role in the prediction of melt pressure, temperature at the gate and the succeeding melt front advancement in the cavity. Using the viscoelastic model one can also control the rapid increase in simulated pressure, temperature, and reduce the filling difference among different cavities. The short shot experiments of micro-motor shaft showed that the predicted melt front from the viscoelastic model is in fair agreement with the corresponding experimental results.
- 21 September 2011
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 19 (8) , 085003
Model and simulation for melt flow in micro-injection molding based on the PTT model
Unsteady viscoelastic flows were studied using the finite element method in this work. The Phan-Thien–Tanner (PTT) model was used to represent the rheological behavior of viscoelastic fluids. To effectively describe the microscale effects, the slip boundary condition and surface tension were added to the mathematical model for melt flow in micro-injection molding. The new variational equation of pressure, including the viscoelastic parameters and slip boundary condition, was generalized using integration by parts. A computer code based on the finite element method and finite difference method was developed to solve the melt flow problem. Numerical simulation revealed that the melt viscoelasticity plays an important role in the prediction of melt pressure, temperature at the gate and the succeeding melt front advancement in the cavity. Using the viscoelastic model one can also control the rapid increase in simulated pressure, temperature, and reduce the filling difference among different cavities. The short shot experiments of micro-motor shaft showed that the predicted melt front from the viscoelastic model is in fair agreement with the corresponding experimental results.
- 1 August 2011
- Published by American Scientific Publishers in Advanced Science Letters
- Vol. 4 (8) , 2907-2910
Dynamic Analysis of Underwater Launched Vehicle During Water Exit
- 1 August 2011
- Published by American Scientific Publishers in Advanced Science Letters
- Vol. 4 (8) , 2907-2910
Dynamic Analysis of Underwater Launched Vehicle During Water Exit
- 24 January 2011
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 133 (1) , 011004
Study on Air Accumulation and Influence on Flow Balance in Micro-Injection Molding
The conventional finite element method was employed to study the relationship between melt filling and air accumulation in micro-cavities. The variational equation for melt flow with slip boundary condition and air resistance was generalized based on Galerkin principle. To investigate the effect of air accumulation, the governing equation for air flow inside runner was established by dimensionless method. An iterative approach was proposed to solve the coupled melt flow problem and air flow problem. Numerical results show that air accumulation can affect the melt filling in micro-cavity, and closely depends on injection speed. Adjusting branch runner distribution can improve the flow balance, which was convinced by a real micro-part manufacturing.
- 24 January 2011
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 133 (1) , 011004
Study on Air Accumulation and Influence on Flow Balance in Micro-Injection Molding
The conventional finite element method was employed to study the relationship between melt filling and air accumulation in micro-cavities. The variational equation for melt flow with slip boundary condition and air resistance was generalized based on Galerkin principle. To investigate the effect of air accumulation, the governing equation for air flow inside runner was established by dimensionless method. An iterative approach was proposed to solve the coupled melt flow problem and air flow problem. Numerical results show that air accumulation can affect the melt filling in micro-cavity, and closely depends on injection speed. Adjusting branch runner distribution can improve the flow balance, which was convinced by a real micro-part manufacturing.
- 8 September 2007
- Published by Springer Nature in Archive of Applied Mechanics
- Vol. 78 (5) , 363-377
Computing flow-induced stresses of injection molding based on the Phan–Thien–Tanner model
- 8 September 2007
- Published by Springer Nature in Archive of Applied Mechanics
- Vol. 78 (5) , 363-377
Computing flow-induced stresses of injection molding based on the Phan–Thien–Tanner model