Romain Cauchois
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Romain Cauchois has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
Beatrice Dubois-Bonvalot
Centre Microélectronique de Provence, Ecole Nationale Supérieure des Mines de Saint-Etienne, Gardanne, France
3 shared publicationsJean-Christophe Fidalgo
Centre Microélectronique de Provence, Ecole Nationale Supérieure des Mines de Saint-Etienne, Gardanne, France
3 shared publicationsKarim Inal
Department of Innovation and Manufacturing Technologies, Gemalto, Gemenos, France
3 shared publicationsMohamed Saadaoui
Department of Innovation and Manufacturing Technologies, Gemalto, Gemenos, France
3 shared publicationsA. Yakoub
Ecole Nationale Supérieure des Mines de St-Etienne, Centre de Microélectronique de Provence, 13120 Gardanne, France
1 shared publicationAbdelwahhab Yakoub
Department of Innovation and Manufacturing Technologies, Gemalto, Gemenos, France
1 shared publication
Latest Publications
- 30 March 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Microstructuring inkjet-printed deposits from silver nanoparticules coalescence to the fabrication of interconnections for electronic devices.
Microstructuration des dépôts imprimés par jet d'encre de la coalescence des nanoparticules d'argent vers la réalisation d'interconnexions de composants électroniques.: Plusieurs défis subsistent pour la migration de l’électronique imprimée vers l’industrie, malgré des avancées récentes. Dans ces travaux de thèse, l’optimisation du procédé d’impression d’encres à base de nanoparticules d’argent (<Ø>=25 nm) en fonction de sa rhéologie et des interactions fluide/substrat a permis de réaliser des interconnexions électriques d’une épaisseur de 500 nm. Ces lignes imprimées sur des substrats silicium ou flexibles sont ensuite recuites par des méthodes conventionnelles (étuve ou infrarouge) ou sélectives (micro-onde) à des températures comprises entre 100 et 300°C.Une meilleure compréhension de la relation procédé/microstructure des couches minces imprimées, via plusieurs caractérisations cristallographiques (DRX, EBSD et EDX), a permis d’optimiser la croissance des domaines nanocristallins, activée pour des énergies de l’ordre de 3 à 5 kJ•mol-1. Outre les faibles contraintes résiduelles (70 MPa), cette optimisation permet d’atteindre de faibles résistivités électriques (3.4 µOhm•cm) associées à un accroissement de la cohérence des réseaux cristallins aux joints de grains. La probabilité de réflexion des électrons à ces interfaces peut être davantage réduite, grâce à une approche innovante de croissance orientée des cristallites par interdiffusion atomique à partir du substrat.La faible rigidité mécanique (E<50 GPa) de ces lignes initialement poreuses nécessite une étape de renforcement par texturation ou par croissance electroless pour résister aux étapes de micro-assemblage et de soudure filaire. La réalisation d’un démonstrateur fonctionnel a ainsi permis de valider la technologie d’impression pour la fabrication de composants électroniques.
- 30 March 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Microstructuring inkjet-printed deposits from silver nanoparticules coalescence to the fabrication of interconnections for electronic devices.
Microstructuration des dépôts imprimés par jet d'encre de la coalescence des nanoparticules d'argent vers la réalisation d'interconnexions de composants électroniques.: Plusieurs défis subsistent pour la migration de l’électronique imprimée vers l’industrie, malgré des avancées récentes. Dans ces travaux de thèse, l’optimisation du procédé d’impression d’encres à base de nanoparticules d’argent (<Ø>=25 nm) en fonction de sa rhéologie et des interactions fluide/substrat a permis de réaliser des interconnexions électriques d’une épaisseur de 500 nm. Ces lignes imprimées sur des substrats silicium ou flexibles sont ensuite recuites par des méthodes conventionnelles (étuve ou infrarouge) ou sélectives (micro-onde) à des températures comprises entre 100 et 300°C.Une meilleure compréhension de la relation procédé/microstructure des couches minces imprimées, via plusieurs caractérisations cristallographiques (DRX, EBSD et EDX), a permis d’optimiser la croissance des domaines nanocristallins, activée pour des énergies de l’ordre de 3 à 5 kJ•mol-1. Outre les faibles contraintes résiduelles (70 MPa), cette optimisation permet d’atteindre de faibles résistivités électriques (3.4 µOhm•cm) associées à un accroissement de la cohérence des réseaux cristallins aux joints de grains. La probabilité de réflexion des électrons à ces interfaces peut être davantage réduite, grâce à une approche innovante de croissance orientée des cristallites par interdiffusion atomique à partir du substrat.La faible rigidité mécanique (E<50 GPa) de ces lignes initialement poreuses nécessite une étape de renforcement par texturation ou par croissance electroless pour résister aux étapes de micro-assemblage et de soudure filaire. La réalisation d’un démonstrateur fonctionnel a ainsi permis de valider la technologie d’impression pour la fabrication de composants électroniques.
- 10 November 2014
- Published by Springer Nature in Electronic Materials Letters
- Vol. 10 (6) , 1175-1183
Large area photonic flash soldering of thin chips on flex foils for flexible electronic systems: In situ temperature measurements and thermal modelling
- 10 November 2014
- Published by Springer Nature in Electronic Materials Letters
- Vol. 10 (6) , 1175-1183
Large area photonic flash soldering of thin chips on flex foils for flexible electronic systems: In situ temperature measurements and thermal modelling
- 14 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 4 (11) , 1879-1886
Photonic Flash Soldering of Thin Chips and SMD Components on Foils for Flexible Electronics
Ultrathin bare die chips and small-size surface mount device components were successfully soldered using a novel roll-to-roll compatible soldering technology. A high-power xenon light flash was used to successfully solder the components to copper tracks on polyimide (PI) and polyethylene terephthalate (PET) flex foils by using a lead-free solder paste. Results are compared with oven-reflowed solder joints on PI substrates. The delicate PET foil substrates were not damaged owing to the selectivity of light absorption, leading to a limited temperature increase in the PET foil while the chip and copper tracks were heated to a temperature high enough to initiate soldering. The microstructure of the soldered joints was investigated and found to be dependent on the photonic flash intensity. Reliability of the photonically soldered joints during damp heat testing and dynamic flexing testing was comparable with the reflowed benchmark and showed increased reliability compared with anisotropic conductive adhesives bonded on PET foils.
- 14 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 4 (11) , 1879-1886
Photonic Flash Soldering of Thin Chips and SMD Components on Foils for Flexible Electronics
Ultrathin bare die chips and small-size surface mount device components were successfully soldered using a novel roll-to-roll compatible soldering technology. A high-power xenon light flash was used to successfully solder the components to copper tracks on polyimide (PI) and polyethylene terephthalate (PET) flex foils by using a lead-free solder paste. Results are compared with oven-reflowed solder joints on PI substrates. The delicate PET foil substrates were not damaged owing to the selectivity of light absorption, leading to a limited temperature increase in the PET foil while the chip and copper tracks were heated to a temperature high enough to initiate soldering. The microstructure of the soldered joints was investigated and found to be dependent on the photonic flash intensity. Reliability of the photonically soldered joints during damp heat testing and dynamic flexing testing was comparable with the reflowed benchmark and showed increased reliability compared with anisotropic conductive adhesives bonded on PET foils.
- Open Access
- 1 August 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 996, 930-935
Microstrain and Residual Stress in Thin-Films Made from Silver Nanoparticles Deposited by Inkjet-Printing Technology
Colloidal suspensions of nanoparticles are increasingly employed in the fabrication process of electronic devices using inkjet-printing technology and a consecutive thermal treatment. The evolution of internal stresses during the conversion of silver nanoparticle-based ink into a metallic thin-film by a thermal sintering process has been investigated by in-situ XRD using the sin2ψ method. Despite the CTE mismatch at the film/substrate interface, the residual stress in silver films (below 70 MPa) remains lower than in conventional PVD thin-films, as a result of the remaining porosity. A Warren-Averbach analysis further showed that the crystallite growth is associated with a minimization of the twin fault density and the elastic microstrain energy above 150°C. A stabilization of the microstructure and internal stress is observed above 300°C. Inkjet-printing technology thus appears as a good alternative to conventional metallization techniques and offers significant opportunities asset for interconnect and electronic packaging.
- 1 August 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 996, 930-935
Open AccessMicrostrain and Residual Stress in Thin-Films Made from Silver Nanoparticles Deposited by Inkjet-Printing Technology
Colloidal suspensions of nanoparticles are increasingly employed in the fabrication process of electronic devices using inkjet-printing technology and a consecutive thermal treatment. The evolution of internal stresses during the conversion of silver nanoparticle-based ink into a metallic thin-film by a thermal sintering process has been investigated by in-situ XRD using the sin2ψ method. Despite the CTE mismatch at the film/substrate interface, the residual stress in silver films (below 70 MPa) remains lower than in conventional PVD thin-films, as a result of the remaining porosity. A Warren-Averbach analysis further showed that the crystallite growth is associated with a minimization of the twin fault density and the elastic microstrain energy above 150°C. A stabilization of the microstructure and internal stress is observed above 300°C. Inkjet-printing technology thus appears as a good alternative to conventional metallization techniques and offers significant opportunities asset for interconnect and electronic packaging.
- 1 June 2013
- Published by Elsevier in Microelectronics Reliability
- Vol. 53 (6) , 885-891
RFID tags for cryogenic applications: Experimental and numerical analysis of thermo-mechanical behaviour
- 1 June 2013
- Published by Elsevier in Microelectronics Reliability
- Vol. 53 (6) , 885-891
RFID tags for cryogenic applications: Experimental and numerical analysis of thermo-mechanical behaviour
- 22 May 2012
- Published by Springer Nature in MRS Proceedings
- Vol. 1401
An Improved In-line Inkjet Printing Process for 3D Multilayer Passive Devices
- 22 May 2012
- Published by Springer Nature in MRS Proceedings
- Vol. 1401
An Improved In-line Inkjet Printing Process for 3D Multilayer Passive Devices
- 9 March 2012
- Published by Springer Nature in Journal of Materials Science
- Vol. 47 (20) , 7110-7116
Impact of variable frequency microwave and rapid thermal sintering on microstructure of inkjet-printed silver nanoparticles
- 9 March 2012
- Published by Springer Nature in Journal of Materials Science
- Vol. 47 (20) , 7110-7116
Impact of variable frequency microwave and rapid thermal sintering on microstructure of inkjet-printed silver nanoparticles
- 10 August 2011
- Published by Springer Nature in MRS Proceedings
- Vol. 1335
Tailoring the Crystallographic Texture and Electrical Properties of Inkjet-printed Interconnects for Use in Microelectronics
- 10 August 2011
- Published by Springer Nature in MRS Proceedings
- Vol. 1335
Tailoring the Crystallographic Texture and Electrical Properties of Inkjet-printed Interconnects for Use in Microelectronics
- 1 September 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Wire-bonding on inkjet-printed silver pads reinforced by electroless plating for chip on flexible board packages
The nanoporous nature of the inkjet printed silver nanoparticles entail low hardness and surface effective contact area for being compatible with pads that are suitable for wire-bonding in electronic packaging. Electroless nickel plating is a selective metal deposition technique which can brings the required thickness and hardness for further pads processing. Here, a 1.7 μm thick nickel layer is deposited on top of 600 nm thick printed and sintered silver nanoparticles using Kapton polyimide as substrate. Prior to plating, a special attention was put on tuning microstructures of printed silver pads by sintering nanoparticles at various temperature ramps (0.1, 10 and 50°C/s) up to 200°C. Results show that fast sintering exhibits the lowest electrical resistivity which is suitable in printed interconnects. However, wire-bonding on nickel pads is best achieved when low sintering ramp is used. This slow sintering presents the highest adhesion strength at the nickel/silver interface since the pores dimensions were restricted to the nanoscale. The validation of the optimized bonding process came from the low electrical contact resistance between plated nickel and the bonded gold wire, and from the wire-pull test which is in accordance with the MIL-STD 883 standard. The actual results show that a compromise has to be found when emphasis is on patterning low resistive interconnects or stiff pads for wire-bonding applications. This compromise is tailored by the sintering engineering.
- 1 September 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Wire-bonding on inkjet-printed silver pads reinforced by electroless plating for chip on flexible board packages
The nanoporous nature of the inkjet printed silver nanoparticles entail low hardness and surface effective contact area for being compatible with pads that are suitable for wire-bonding in electronic packaging. Electroless nickel plating is a selective metal deposition technique which can brings the required thickness and hardness for further pads processing. Here, a 1.7 μm thick nickel layer is deposited on top of 600 nm thick printed and sintered silver nanoparticles using Kapton polyimide as substrate. Prior to plating, a special attention was put on tuning microstructures of printed silver pads by sintering nanoparticles at various temperature ramps (0.1, 10 and 50°C/s) up to 200°C. Results show that fast sintering exhibits the lowest electrical resistivity which is suitable in printed interconnects. However, wire-bonding on nickel pads is best achieved when low sintering ramp is used. This slow sintering presents the highest adhesion strength at the nickel/silver interface since the pores dimensions were restricted to the nanoscale. The validation of the optimized bonding process came from the low electrical contact resistance between plated nickel and the bonded gold wire, and from the wire-pull test which is in accordance with the MIL-STD 883 standard. The actual results show that a compromise has to be found when emphasis is on patterning low resistive interconnects or stiff pads for wire-bonding applications. This compromise is tailored by the sintering engineering.