D. Philip Selvaraj
Research Subjects
D. Philip Selvaraj has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- K. John Joshua
PSN college of Engineering and Technology
4 shared publications - Ebenezer Jacob Dhas Darwin Selvi
Division of Mechanical Engineering, Karunya Institute of Technology and Sciences, Coimbatore, India
3 shared publications P. Chandramohan
2 shared publicationsP. George
Department of Mechanical Engineering School of Engineering & Information Technology, Manipal Academy of Higher Education Dubai Campus Dubai 345050 UAE
2 shared publicationsP. Ramkumar
Department of Mechanical Engineering, Karunya University, Coimbatore-6411114, Tamil Nadu, India
2 shared publicationsP. Richard Philip
Karpagam College of Engineering
2 shared publications
Latest Publications
- 7 September 2026
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 57 (9) , 937-959
Multi–criteria optimization of cutting parameters during dry computer numerical controlled milling of martensitic stainless steels 410 and 420 using grey relational analysis
This study optimized cutting parameters for dry computer numerical control milling of martensitic stainless steels (410/420) using grey relational analysis and identified the optimal parameters as a spindle speed of 1500 min −1 , a depth of cut of 0.3 mm, and feed rate of 30 mm/min, achieving a balanced reduction in R a (0.62 μm– 0.66 μm) and F c 164 – 200 N) and with a balanced temperature of 44 – 48 °C. Analysis of variance revealed that the depth of cut was the dominant factor, contributing 57 % (martensitic stainless steel 410) and 62 % (martensitic stainless steel 420) to the grey relational grade variance. This was followed by the feed rate (27 % and 25 %, respectively) and the spindle speed (12 % and 10 %, respectively). The intermediate spindle speed of 1500 rpm softened the cutting zone, reducing F c and R a . Normal probability plots confirmed residual normality, validating the reliability of the experiment. Surface plots revealed peak grey relational grade values at a medium spindle speed and a low depth of cut/feed. Scanning electron microscope is employed for tool wear analysis. This study shows that parameter synergy, rather than individual adjustments, is essential for multi‐objective optimization in hard‐to‐machine steels.
- 7 September 2026
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 57 (9) , 937-959
Multi–criteria optimization of cutting parameters during dry computer numerical controlled milling of martensitic stainless steels 410 and 420 using grey relational analysis
This study optimized cutting parameters for dry computer numerical control milling of martensitic stainless steels (410/420) using grey relational analysis and identified the optimal parameters as a spindle speed of 1500 min −1 , a depth of cut of 0.3 mm, and feed rate of 30 mm/min, achieving a balanced reduction in R a (0.62 μm– 0.66 μm) and F c 164 – 200 N) and with a balanced temperature of 44 – 48 °C. Analysis of variance revealed that the depth of cut was the dominant factor, contributing 57 % (martensitic stainless steel 410) and 62 % (martensitic stainless steel 420) to the grey relational grade variance. This was followed by the feed rate (27 % and 25 %, respectively) and the spindle speed (12 % and 10 %, respectively). The intermediate spindle speed of 1500 rpm softened the cutting zone, reducing F c and R a . Normal probability plots confirmed residual normality, validating the reliability of the experiment. Surface plots revealed peak grey relational grade values at a medium spindle speed and a low depth of cut/feed. Scanning electron microscope is employed for tool wear analysis. This study shows that parameter synergy, rather than individual adjustments, is essential for multi‐objective optimization in hard‐to‐machine steels.
- 21 March 2026
- Published by Springer Nature in Interactions
- Vol. 247 (1) , 85
Mathematical model development for cutting temperature of AMS 5659- 15-5 PH stainless steel in milling operation using response surface methodology
- 21 March 2026
- Published by Springer Nature in Interactions
- Vol. 247 (1) , 85
Mathematical model development for cutting temperature of AMS 5659- 15-5 PH stainless steel in milling operation using response surface methodology
- 23 February 2026
- Published by Springer Nature in Interactions
- Vol. 247 (1) , 42
Material selection and development of button controlled automatic gear changer for two wheelers
- 23 February 2026
- Published by Springer Nature in Interactions
- Vol. 247 (1) , 42
Material selection and development of button controlled automatic gear changer for two wheelers
- 28 January 2025
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 56 (2) , 281-289
Effect of machining parameters on the machinability of 15‐5 precipitation hardened stainless steel during dry turning
This research presents the studies on the effect of machining variables and the empirical modeling of machinability output responses during dry turning of 15–5 precipitation‐hardened stainless steel (PHSS) using the taguchi meta‐heuristic algorithm. L9 orthogonal array (OA) robust experimental design was selected for conducting the dry turning operations. The input variables included cutting velocity, depth of cut, and feed rate, while the output responses measured were surface roughness (Ra) and cutting force (Fc). The influence of these process variables was determined through analysis of variance (ANOVA). ANOVA results revealed that cutting speed, feed rate and depth of cut were impacting the average surface roughness by 36 %, 29 %, and 31 %, respectively and influencing the cutting force by 2 %, 16 %, and 72 %, respectively, during turning operation. Empirical models for predicting cutting force and surface roughness were developed using the Taguchi meta‐heuristic algorithm. The optimization process resulted in a significant reduction in surface roughness, with Ra decreasing by 17 % and a notable decrease in cutting force, Fc, by 8 %. These numerical improvements indicate that the proposed optimization approach substantially enhances machining performance, validating its effectiveness.
- 28 January 2025
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 56 (2) , 281-289
Effect of machining parameters on the machinability of 15‐5 precipitation hardened stainless steel during dry turning
This research presents the studies on the effect of machining variables and the empirical modeling of machinability output responses during dry turning of 15–5 precipitation‐hardened stainless steel (PHSS) using the taguchi meta‐heuristic algorithm. L9 orthogonal array (OA) robust experimental design was selected for conducting the dry turning operations. The input variables included cutting velocity, depth of cut, and feed rate, while the output responses measured were surface roughness (Ra) and cutting force (Fc). The influence of these process variables was determined through analysis of variance (ANOVA). ANOVA results revealed that cutting speed, feed rate and depth of cut were impacting the average surface roughness by 36 %, 29 %, and 31 %, respectively and influencing the cutting force by 2 %, 16 %, and 72 %, respectively, during turning operation. Empirical models for predicting cutting force and surface roughness were developed using the Taguchi meta‐heuristic algorithm. The optimization process resulted in a significant reduction in surface roughness, with Ra decreasing by 17 % and a notable decrease in cutting force, Fc, by 8 %. These numerical improvements indicate that the proposed optimization approach substantially enhances machining performance, validating its effectiveness.
- 29 August 2024
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (3) , 035549
Effect of machining parameters on average surface roughness during computer numerical controlled dry milling of high strength AISI 420 martensitic stainless steel
This study focuses on developing an empirical model for average surface roughness during computer numerical controlled (CNC) dry milling of AISI 420 martensitic stainless steel, utilizing response surface methodology (RSM). Experiments were designed with three levels of axial depth of cut, feed rate, and spindle speed to quantify their impact on surface roughness. The RSM-Box-Behnken design was employed to construct the empirical model. Model adequacy was validated through residual analysis and analysis of variance (ANOVA). Analysis of the main effects and interaction effects revealed that the primary influences on average surface roughness were the feed rate, spindle speed, and axial depth of cut, while interaction effects were less significant. Optimal cutting conditions were determined to be a spindle speed of 1500 rpm, a feed rate of 30 mm min−1, and an axial depth of cut of 0.3 mm. The model’s validity was further confirmed through additional validation tests.
- 29 August 2024
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (3) , 035549
Effect of machining parameters on average surface roughness during computer numerical controlled dry milling of high strength AISI 420 martensitic stainless steel
This study focuses on developing an empirical model for average surface roughness during computer numerical controlled (CNC) dry milling of AISI 420 martensitic stainless steel, utilizing response surface methodology (RSM). Experiments were designed with three levels of axial depth of cut, feed rate, and spindle speed to quantify their impact on surface roughness. The RSM-Box-Behnken design was employed to construct the empirical model. Model adequacy was validated through residual analysis and analysis of variance (ANOVA). Analysis of the main effects and interaction effects revealed that the primary influences on average surface roughness were the feed rate, spindle speed, and axial depth of cut, while interaction effects were less significant. Optimal cutting conditions were determined to be a spindle speed of 1500 rpm, a feed rate of 30 mm min−1, and an axial depth of cut of 0.3 mm. The model’s validity was further confirmed through additional validation tests.
- 21 August 2020
- Published by Springer Nature
- p. 869-877
Some Studies on Surface Roughness of AISI 304 Austenitic Stainless Steel in Dry Turning Operation
- 21 August 2020
- Published by Springer Nature
- p. 869-877
Some Studies on Surface Roughness of AISI 304 Austenitic Stainless Steel in Dry Turning Operation
- Open Access
- 1 June 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 872 (1) , 012064
Green composite materials for green technology in the automotive industry
The utilization of inexhaustible assets is a significant achievement towards viable individual versatility. Using natural fibers is a worthwhile input towards the ecological mindful of individual transportation. There were numerous advantages related with green initiative which includes better acoustic properties, weight and cost saving potential along with better working conditions. This research contributes a review in the expansive field of green composites searching out for materials with possibilities to be applied on vehicle body parts. The usefulness of the regular fiber composites for car industry was outlined. In addition, this work distinguishes a different method for assessing natural fiber composites compared with general desired criteria. This leads to a situation that natural fiber is no longer an environmental waste by its large scale industrial application which is being discussed here. Here different criteria levels were given to the categorize natural fibers. This criteria serves as a basic tool for the engineers while selecting the natural fiber composites based on its practical application. The automobile business is in the driving seat of green composites since it is here that the need is most prominent. Today we’re not offering materials that will change the landscape in the way that metal replacement did, but we are beginning to offer natural fiber composites that will present improvements, particularly in areas such as impact resistance, chemical resistance and, in some cases, process cost.
- 1 June 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 872 (1) , 012064
Open AccessGreen composite materials for green technology in the automotive industry
The utilization of inexhaustible assets is a significant achievement towards viable individual versatility. Using natural fibers is a worthwhile input towards the ecological mindful of individual transportation. There were numerous advantages related with green initiative which includes better acoustic properties, weight and cost saving potential along with better working conditions. This research contributes a review in the expansive field of green composites searching out for materials with possibilities to be applied on vehicle body parts. The usefulness of the regular fiber composites for car industry was outlined. In addition, this work distinguishes a different method for assessing natural fiber composites compared with general desired criteria. This leads to a situation that natural fiber is no longer an environmental waste by its large scale industrial application which is being discussed here. Here different criteria levels were given to the categorize natural fibers. This criteria serves as a basic tool for the engineers while selecting the natural fiber composites based on its practical application. The automobile business is in the driving seat of green composites since it is here that the need is most prominent. Today we’re not offering materials that will change the landscape in the way that metal replacement did, but we are beginning to offer natural fiber composites that will present improvements, particularly in areas such as impact resistance, chemical resistance and, in some cases, process cost.
- 30 October 2019
- Published by Blue Eyes Intelligence Engineering and Sciences Engineering and Sciences Publication (BEIESP) in International Journal of Innovative Technology and Exploring Engineering
- Vol. 8 (12) , 4709-4711
Optimization of Cutting Force of AISI 304 Austenitic Stainless Steel in a Wet Turning Process
The objective of this research work is to optimize the machining variables of AISI 304 austenitic stainless steel during wet turning operation. The input parameters considered are depth, feed and cutting speed. The output response considered is cutting force. Taguchi technique is used to find the optimum machining conditions for cutting force. ANOVA is used to determine the effect of input variables on the cutting force. ANOVA results indicated that the most significant variable affecting the cutting force during the wet turning process is depth of cut.
- 30 October 2019
- Published by Blue Eyes Intelligence Engineering and Sciences Engineering and Sciences Publication (BEIESP) in International Journal of Innovative Technology and Exploring Engineering
- Vol. 8 (12) , 4709-4711
Optimization of Cutting Force of AISI 304 Austenitic Stainless Steel in a Wet Turning Process
The objective of this research work is to optimize the machining variables of AISI 304 austenitic stainless steel during wet turning operation. The input parameters considered are depth, feed and cutting speed. The output response considered is cutting force. Taguchi technique is used to find the optimum machining conditions for cutting force. ANOVA is used to determine the effect of input variables on the cutting force. ANOVA results indicated that the most significant variable affecting the cutting force during the wet turning process is depth of cut.
- 30 September 2019
- Published by Blue Eyes Intelligence Engineering and Sciences Engineering and Sciences Publication (BEIESP) in International Journal of Recent Technology and Engineering (IJRTE)
- Vol. 8 (3) , 5840-5843
Optimization of milling parameters of ASTM a 995 grade 4A Duplex Stainless Steel using Taguchi Technique
This work explains the optimization of milling variables of duplex stainless steel by employing Taguchi technique. The milling tests are carried out at three levels of feeds and spindle speeds. The average of results and ANOVA are employed to investigate the machining performances. The results exposed that the feed and spindle speed are the most important variables influencing the cutting force and surface finish. It is determined that, the spindle speed is the most important variable influencing the tool wear. Confirmation tests are conducted at optimum machining conditions in order to verify the predicted results and the error is within 5%.
- 30 September 2019
- Published by Blue Eyes Intelligence Engineering and Sciences Engineering and Sciences Publication (BEIESP) in International Journal of Recent Technology and Engineering (IJRTE)
- Vol. 8 (3) , 5840-5843
Optimization of milling parameters of ASTM a 995 grade 4A Duplex Stainless Steel using Taguchi Technique
This work explains the optimization of milling variables of duplex stainless steel by employing Taguchi technique. The milling tests are carried out at three levels of feeds and spindle speeds. The average of results and ANOVA are employed to investigate the machining performances. The results exposed that the feed and spindle speed are the most important variables influencing the cutting force and surface finish. It is determined that, the spindle speed is the most important variable influencing the tool wear. Confirmation tests are conducted at optimum machining conditions in order to verify the predicted results and the error is within 5%.