Ebenezer Jacob Dhas Darwin Selvi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ebenezer Jacob Dhas Darwin Selvi has a total of 71 co-authors. Here are the top co-authors by number of shared publications:
- K. Leo Dev Wins
Department of Mechanical Engineering Karunya Institute of Technology and Sciences Coimbatore 641114 Tamilnadu India
11 shared publications C. Velmurugan
7 shared publicationsB. Anuja Beatrice
Department of Computer Applications, Sri Krishna Arts and Science College, Coimbatore, India
6 shared publicationsK. Leo Dev Wins
6 shared publicationsPradeep George
Department of Mechanical Engineering and Energy, De Montfort University, Dubai, UAE
6 shared publications- .R. Raja
Associate Professor, Department of Mechanical Engineering, Karunya Institute of Technology and Sciences, Coimbatore, Tamil Nadu, India
4 shared publications
Latest Publications
- Open Access
Reinforcement-Matrix Interactions and Strengthening Model Validity in Magnesium Matrix Composites: A Critical Review
Magnesium matrix composites are attractive for weight-critical structures, yet the way their strength is explained has hardly changed in two decades. Most studies partition the yield-strength gain into load transfer, Hall–Petch, Orowan, and thermal-mismatch increments and combine them by a linear, root-sum-square, or compound rule. Reinforcement alters the interphase chemistry, the recrystallised grain structure and texture, the relative contribution of twinning and non-basal slip to deformation, and the kinetics of matrix precipitation. The inputs to all terms in the equation change simultaneously, so the terms are not independent in these systems. A sensitivity analysis of the equation for a typical nanoparticle-reinforced alloy showed that the predicted gain at 1 vol% reinforcement could be as low as 100 MPa or as high as 220 MPa. Independent predictions typically miss the experimental results by 10–165%. Twinning-sensitive behaviour is almost never included in strengthening analyses. We propose a minimum evidence chain for strengthening analyses: a matrix control processed identically to the reinforced alloy, measured rather than assumed inputs, compression and load-unload-reload tests on the reinforced alloy, texture-aware coupled models with uncertainty, and blind validation outside the calibration window. This approach could move strengthening analyses from post hoc accounting towards predictive design.
Open AccessReinforcement-Matrix Interactions and Strengthening Model Validity in Magnesium Matrix Composites: A Critical Review
Magnesium matrix composites are attractive for weight-critical structures, yet the way their strength is explained has hardly changed in two decades. Most studies partition the yield-strength gain into load transfer, Hall–Petch, Orowan, and thermal-mismatch increments and combine them by a linear, root-sum-square, or compound rule. Reinforcement alters the interphase chemistry, the recrystallised grain structure and texture, the relative contribution of twinning and non-basal slip to deformation, and the kinetics of matrix precipitation. The inputs to all terms in the equation change simultaneously, so the terms are not independent in these systems. A sensitivity analysis of the equation for a typical nanoparticle-reinforced alloy showed that the predicted gain at 1 vol% reinforcement could be as low as 100 MPa or as high as 220 MPa. Independent predictions typically miss the experimental results by 10–165%. Twinning-sensitive behaviour is almost never included in strengthening analyses. We propose a minimum evidence chain for strengthening analyses: a matrix control processed identically to the reinforced alloy, measured rather than assumed inputs, compression and load-unload-reload tests on the reinforced alloy, texture-aware coupled models with uncertainty, and blind validation outside the calibration window. This approach could move strengthening analyses from post hoc accounting towards predictive design.
- 7 October 2026
- Published by Taylor & Francis in Welding International
- p. 1-14
Analysis of tensile properties, fracture characteristics, and microstructural features in friction stir welding of dissimilar aluminium alloys reinforced with Al 2 O 3
1. Aluminium alloys are extensively used in shipbuilding, aerospace, and automotive industries due to their high strength-to-weight ratio, good ductility, and corrosion resistance. In many structur...
- 7 October 2026
- Published by Taylor & Francis in Welding International
- p. 1-14
Analysis of tensile properties, fracture characteristics, and microstructural features in friction stir welding of dissimilar aluminium alloys reinforced with Al 2 O 3
1. Aluminium alloys are extensively used in shipbuilding, aerospace, and automotive industries due to their high strength-to-weight ratio, good ductility, and corrosion resistance. In many structur...
- 7 September 2026
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 57 (9) , 937-959
Multi–criteria optimization of cutting parameters during dry computer numerical controlled milling of martensitic stainless steels 410 and 420 using grey relational analysis
This study optimized cutting parameters for dry computer numerical control milling of martensitic stainless steels (410/420) using grey relational analysis and identified the optimal parameters as a spindle speed of 1500 min −1 , a depth of cut of 0.3 mm, and feed rate of 30 mm/min, achieving a balanced reduction in R a (0.62 μm– 0.66 μm) and F c 164 – 200 N) and with a balanced temperature of 44 – 48 °C. Analysis of variance revealed that the depth of cut was the dominant factor, contributing 57 % (martensitic stainless steel 410) and 62 % (martensitic stainless steel 420) to the grey relational grade variance. This was followed by the feed rate (27 % and 25 %, respectively) and the spindle speed (12 % and 10 %, respectively). The intermediate spindle speed of 1500 rpm softened the cutting zone, reducing F c and R a . Normal probability plots confirmed residual normality, validating the reliability of the experiment. Surface plots revealed peak grey relational grade values at a medium spindle speed and a low depth of cut/feed. Scanning electron microscope is employed for tool wear analysis. This study shows that parameter synergy, rather than individual adjustments, is essential for multi‐objective optimization in hard‐to‐machine steels.
- 7 September 2026
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 57 (9) , 937-959
Multi–criteria optimization of cutting parameters during dry computer numerical controlled milling of martensitic stainless steels 410 and 420 using grey relational analysis
This study optimized cutting parameters for dry computer numerical control milling of martensitic stainless steels (410/420) using grey relational analysis and identified the optimal parameters as a spindle speed of 1500 min −1 , a depth of cut of 0.3 mm, and feed rate of 30 mm/min, achieving a balanced reduction in R a (0.62 μm– 0.66 μm) and F c 164 – 200 N) and with a balanced temperature of 44 – 48 °C. Analysis of variance revealed that the depth of cut was the dominant factor, contributing 57 % (martensitic stainless steel 410) and 62 % (martensitic stainless steel 420) to the grey relational grade variance. This was followed by the feed rate (27 % and 25 %, respectively) and the spindle speed (12 % and 10 %, respectively). The intermediate spindle speed of 1500 rpm softened the cutting zone, reducing F c and R a . Normal probability plots confirmed residual normality, validating the reliability of the experiment. Surface plots revealed peak grey relational grade values at a medium spindle speed and a low depth of cut/feed. Scanning electron microscope is employed for tool wear analysis. This study shows that parameter synergy, rather than individual adjustments, is essential for multi‐objective optimization in hard‐to‐machine steels.
- 18 September 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (7) , 6853-6865
Microstructure and Mechanical Properties of Copper Metal Matrix Composites Reinforced with Hybrid Ceramic and Fuse Holder Scrap
- 18 September 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (7) , 6853-6865
Microstructure and Mechanical Properties of Copper Metal Matrix Composites Reinforced with Hybrid Ceramic and Fuse Holder Scrap
- 1 September 2025
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 56 (9) , 1173-1182
Advanced solid‐state processing techniques for enhanced strengthening of lightweight materials: the evolution of high entropy alloy composites
Recent advancements in material science have advanced high‐entropy alloy (HEA) composites through sophisticated solid‐state processing techniques, achieving remarkable mechanical properties for lightweight applications. Methods like non‐equilibrium solidification, magnetic field‐assisted processing, and laser shock peening have enhanced dispersion strengthening, yielding composites with a 35 % increase in yield strength and 40 % improved hardness compared to traditional aluminum alloys. Integrating micro/nanoscale reinforcements ‐ such as 5 vol.‐% graphene nanoplatelets or 2 wt.‐% carbon nanotubes ‐ with aluminum matrices via mechanical ball‐milling and ultrasound‐assisted exfoliation ensures uniform dispersion, reducing clustering by 60 %. Machine learning algorithms optimize processing parameters, improving particle distribution homogeneity by 25 %. Dispersion strengthening, driven by 10 nm – 50 nm particles, impedes dislocation motion, boosting wear resistance by 30 %. Biomimetic liquid‐state processing, mimicking nacre‐like structures, and responsive nanoparticles enable adaptive responses, enhancing fatigue life by 20 %. These advancements facilitate applications in aerospace, biomedical, and energy sectors, promising transformative impacts. Continued research into sustainable synthesis and hybrid nano composites will further elevate material performance, redefining technological capabilities in material science.
- 1 September 2025
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 56 (9) , 1173-1182
Advanced solid‐state processing techniques for enhanced strengthening of lightweight materials: the evolution of high entropy alloy composites
Recent advancements in material science have advanced high‐entropy alloy (HEA) composites through sophisticated solid‐state processing techniques, achieving remarkable mechanical properties for lightweight applications. Methods like non‐equilibrium solidification, magnetic field‐assisted processing, and laser shock peening have enhanced dispersion strengthening, yielding composites with a 35 % increase in yield strength and 40 % improved hardness compared to traditional aluminum alloys. Integrating micro/nanoscale reinforcements ‐ such as 5 vol.‐% graphene nanoplatelets or 2 wt.‐% carbon nanotubes ‐ with aluminum matrices via mechanical ball‐milling and ultrasound‐assisted exfoliation ensures uniform dispersion, reducing clustering by 60 %. Machine learning algorithms optimize processing parameters, improving particle distribution homogeneity by 25 %. Dispersion strengthening, driven by 10 nm – 50 nm particles, impedes dislocation motion, boosting wear resistance by 30 %. Biomimetic liquid‐state processing, mimicking nacre‐like structures, and responsive nanoparticles enable adaptive responses, enhancing fatigue life by 20 %. These advancements facilitate applications in aerospace, biomedical, and energy sectors, promising transformative impacts. Continued research into sustainable synthesis and hybrid nano composites will further elevate material performance, redefining technological capabilities in material science.
- 28 July 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (3) , 035527
Corrosion studies on Al 7075/boron carbide/titanium/graphite hybrid composites for heat exchangers
In this study, hybrid composites of Al7075 reinforced with boron carbide (B4C), titanium (Ti), and graphite (Gr) were synthesized using the stir casting technique and was investigated to assess their suitability for aerospace applications. Six different compositions were prepared by varying the vol% of B4C and Ti and maintaining a constant vol% of graphite in all composites. The physical and structural characteristics were analyzed through density measurements, porosity evaluation, and x-ray diffraction (XRD) analysis. The experimental and theoretical density values showed a decreasing trend with increased reinforcement, Porosity values were found to decrease with higher Ti content. XRD confirmed the presence of Al matrix phases along with B4C, Ti, and graphite, , indicating uniform distribution and phase stability. Corrosion resistance was assessed using static immersion tests, polarization studies, Nyquist plots, and Bode plots. The base alloy demonstrated susceptibility to galvanic corrosion, with minimal passivation. Composites with boron carbide showed moderate corrosion rate (−1.479 mm y−1), and those with titanium exhibited remarkable improvements (−1.116 mm y−1). The polarization curves of the reinforced composites displayed lower current densities in the anodic region with an Ecorr and Icorr value of 776.856 mV and 8.332 mA for composite reinforced with boron carbide and 727.265 mV and 8.001 mA for composites reinforced with titanium, indicating enhanced passivation and reduced corrosion rates. Nyquist plots revealed larger semicircular arcs for titanium-reinforced composites, signifying higher charge transfer resistance (Rct). Among the tested compositions, the hybrid composite with 7 vol% Ti, 3 vol% B4C, and 2 vol% Gr exhibited improved passivation, and superior corrosion resistance.
- 28 July 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (3) , 035527
Corrosion studies on Al 7075/boron carbide/titanium/graphite hybrid composites for heat exchangers
In this study, hybrid composites of Al7075 reinforced with boron carbide (B4C), titanium (Ti), and graphite (Gr) were synthesized using the stir casting technique and was investigated to assess their suitability for aerospace applications. Six different compositions were prepared by varying the vol% of B4C and Ti and maintaining a constant vol% of graphite in all composites. The physical and structural characteristics were analyzed through density measurements, porosity evaluation, and x-ray diffraction (XRD) analysis. The experimental and theoretical density values showed a decreasing trend with increased reinforcement, Porosity values were found to decrease with higher Ti content. XRD confirmed the presence of Al matrix phases along with B4C, Ti, and graphite, , indicating uniform distribution and phase stability. Corrosion resistance was assessed using static immersion tests, polarization studies, Nyquist plots, and Bode plots. The base alloy demonstrated susceptibility to galvanic corrosion, with minimal passivation. Composites with boron carbide showed moderate corrosion rate (−1.479 mm y−1), and those with titanium exhibited remarkable improvements (−1.116 mm y−1). The polarization curves of the reinforced composites displayed lower current densities in the anodic region with an Ecorr and Icorr value of 776.856 mV and 8.332 mA for composite reinforced with boron carbide and 727.265 mV and 8.001 mA for composites reinforced with titanium, indicating enhanced passivation and reduced corrosion rates. Nyquist plots revealed larger semicircular arcs for titanium-reinforced composites, signifying higher charge transfer resistance (Rct). Among the tested compositions, the hybrid composite with 7 vol% Ti, 3 vol% B4C, and 2 vol% Gr exhibited improved passivation, and superior corrosion resistance.
- 28 January 2025
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 56 (2) , 281-289
Effect of machining parameters on the machinability of 15‐5 precipitation hardened stainless steel during dry turning
This research presents the studies on the effect of machining variables and the empirical modeling of machinability output responses during dry turning of 15–5 precipitation‐hardened stainless steel (PHSS) using the taguchi meta‐heuristic algorithm. L9 orthogonal array (OA) robust experimental design was selected for conducting the dry turning operations. The input variables included cutting velocity, depth of cut, and feed rate, while the output responses measured were surface roughness (Ra) and cutting force (Fc). The influence of these process variables was determined through analysis of variance (ANOVA). ANOVA results revealed that cutting speed, feed rate and depth of cut were impacting the average surface roughness by 36 %, 29 %, and 31 %, respectively and influencing the cutting force by 2 %, 16 %, and 72 %, respectively, during turning operation. Empirical models for predicting cutting force and surface roughness were developed using the Taguchi meta‐heuristic algorithm. The optimization process resulted in a significant reduction in surface roughness, with Ra decreasing by 17 % and a notable decrease in cutting force, Fc, by 8 %. These numerical improvements indicate that the proposed optimization approach substantially enhances machining performance, validating its effectiveness.
- 28 January 2025
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 56 (2) , 281-289
Effect of machining parameters on the machinability of 15‐5 precipitation hardened stainless steel during dry turning
This research presents the studies on the effect of machining variables and the empirical modeling of machinability output responses during dry turning of 15–5 precipitation‐hardened stainless steel (PHSS) using the taguchi meta‐heuristic algorithm. L9 orthogonal array (OA) robust experimental design was selected for conducting the dry turning operations. The input variables included cutting velocity, depth of cut, and feed rate, while the output responses measured were surface roughness (Ra) and cutting force (Fc). The influence of these process variables was determined through analysis of variance (ANOVA). ANOVA results revealed that cutting speed, feed rate and depth of cut were impacting the average surface roughness by 36 %, 29 %, and 31 %, respectively and influencing the cutting force by 2 %, 16 %, and 72 %, respectively, during turning operation. Empirical models for predicting cutting force and surface roughness were developed using the Taguchi meta‐heuristic algorithm. The optimization process resulted in a significant reduction in surface roughness, with Ra decreasing by 17 % and a notable decrease in cutting force, Fc, by 8 %. These numerical improvements indicate that the proposed optimization approach substantially enhances machining performance, validating its effectiveness.
- 29 August 2024
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (3) , 035549
Effect of machining parameters on average surface roughness during computer numerical controlled dry milling of high strength AISI 420 martensitic stainless steel
This study focuses on developing an empirical model for average surface roughness during computer numerical controlled (CNC) dry milling of AISI 420 martensitic stainless steel, utilizing response surface methodology (RSM). Experiments were designed with three levels of axial depth of cut, feed rate, and spindle speed to quantify their impact on surface roughness. The RSM-Box-Behnken design was employed to construct the empirical model. Model adequacy was validated through residual analysis and analysis of variance (ANOVA). Analysis of the main effects and interaction effects revealed that the primary influences on average surface roughness were the feed rate, spindle speed, and axial depth of cut, while interaction effects were less significant. Optimal cutting conditions were determined to be a spindle speed of 1500 rpm, a feed rate of 30 mm min−1, and an axial depth of cut of 0.3 mm. The model’s validity was further confirmed through additional validation tests.
- 29 August 2024
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (3) , 035549
Effect of machining parameters on average surface roughness during computer numerical controlled dry milling of high strength AISI 420 martensitic stainless steel
This study focuses on developing an empirical model for average surface roughness during computer numerical controlled (CNC) dry milling of AISI 420 martensitic stainless steel, utilizing response surface methodology (RSM). Experiments were designed with three levels of axial depth of cut, feed rate, and spindle speed to quantify their impact on surface roughness. The RSM-Box-Behnken design was employed to construct the empirical model. Model adequacy was validated through residual analysis and analysis of variance (ANOVA). Analysis of the main effects and interaction effects revealed that the primary influences on average surface roughness were the feed rate, spindle speed, and axial depth of cut, while interaction effects were less significant. Optimal cutting conditions were determined to be a spindle speed of 1500 rpm, a feed rate of 30 mm min−1, and an axial depth of cut of 0.3 mm. The model’s validity was further confirmed through additional validation tests.
- 14 August 2024
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 55 (9) , 1276-1282
Effect of tungsten carbide and titanium dioxide particles on the properties of aluminium alloy 5052 hybrid composites
Aerospace and automotive industries, among others, utilize reinforced aluminium metal matrix composite materials extensively. Aluminium alloy 5052 matrix was reinforced with tungsten carbide and titanium dioxide particulate reinforcements by varying their weight fractions, to fabricate the hybrid composites. The melt‐stir casting route was used to process the materials, and their characteristics were determined by measuring Vickers microhardness, tensile strength and peak elongation. The cost‐effectiveness and productivity of the melt‐stir casting route led to its selection. Investigations were carried out to assess how reinforcement particles were mixed into the aluminium alloy matrix using scanning electron microscopy and energy‐dispersive x‐ray analysis. The microstructure of aluminium alloy 5052 showed a distinct homogenous structural integrity. Adding tungsten carbide and titanium dioxide particles to aluminium alloy 5052 led to a 6.57 % rise in the Vickers microhardness value. The tensile strength of the hybrid composites made of aluminium, tungsten carbide, and titanium dioxide increased by as much as 8.7 %. The findings demonstrated that all of the hybrid composites failed due to particle fracture and ductile fracture in the case of the as‐cast aluminium alloy 5052.
- 14 August 2024
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 55 (9) , 1276-1282
Effect of tungsten carbide and titanium dioxide particles on the properties of aluminium alloy 5052 hybrid composites
Aerospace and automotive industries, among others, utilize reinforced aluminium metal matrix composite materials extensively. Aluminium alloy 5052 matrix was reinforced with tungsten carbide and titanium dioxide particulate reinforcements by varying their weight fractions, to fabricate the hybrid composites. The melt‐stir casting route was used to process the materials, and their characteristics were determined by measuring Vickers microhardness, tensile strength and peak elongation. The cost‐effectiveness and productivity of the melt‐stir casting route led to its selection. Investigations were carried out to assess how reinforcement particles were mixed into the aluminium alloy matrix using scanning electron microscopy and energy‐dispersive x‐ray analysis. The microstructure of aluminium alloy 5052 showed a distinct homogenous structural integrity. Adding tungsten carbide and titanium dioxide particles to aluminium alloy 5052 led to a 6.57 % rise in the Vickers microhardness value. The tensile strength of the hybrid composites made of aluminium, tungsten carbide, and titanium dioxide increased by as much as 8.7 %. The findings demonstrated that all of the hybrid composites failed due to particle fracture and ductile fracture in the case of the as‐cast aluminium alloy 5052.