TKTai-Haur Kuo

Tai-Haur Kuo

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tai-Haur Kuo has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Low-EMI, High-DR Class-D Audio Amplifier With Double-Sided Voltage-Boosting Modulation

    by Jhuang-Wei Cyue, Tai-Haur Kuo

    This article presents a digital-input class-D audio amplifier (CDA) that employs a double-sided voltage-boosting (DSVB) modulation scheme, integrating a capacitively coupled chopper amplifier (CCCA) with a single-inductor buck–boost power stage. The CCCA achieves a high dynamic range (DR) due to its very low noise floor and is implemented with common low-voltage (LV) input devices, while the voltage-boosting power stage achieves a boosted output power ( $P_{\mathrm {OUT}}$ ) with good power efficiency due to its single-stage power delivery. Compared with prior-art CDAs utilizing a capacitive-feedback scheme with two off-chip inductors, this work uses only a single off-chip inductor and has additional output voltage ( $V_{\mathrm {OUT}}$ ) boost capability. The proposed DSVB modulation doubles the effective switching frequency to enhance the LC attenuation, leading to reduced differential-mode electromagnetic interference (EMI) and, unlike typical BD modulation, no modulation-induced common-mode EMI is generated. Compared with the other state-of-the-art LV digital-input CDAs, this work’s CDA, fabricated using a 0.5- $\mu $ m process, achieves the highest DR of 121.3 dB and peak signal-to-noise ratio (PSNR) of 115 dB, as well as a competitive minimal total harmonic distortion plus noise (THD+N) of 0.0019%. It can deliver a maximum $P_{\mathrm {OUT}}$ of 1.6 W into an 8- $\Omega $ load with a peak power efficiency of 87.2%.


  • A 72-dB SNDR 130-MS/s 0.8-mW Pipelined-SAR ADC Using a Distributed Averaging Correlated Level Shifting Ring Amplifier

    by Jia-Ching Wang, Tai-Haur Kuo

    This article presents a 14-b 130-MS/s two-stage pipelined-SAR analog-to-digital converter (ADC) using a distributed averaging correlated level shifting (DACLS) ring amplifier as its residue amplifier (RA). Compared to the prior CLS and ACLS techniques that reduce the RA gain error due to their finite open-loop gain, the proposed DACLS ring amplifier no longer requires an extra level-shifting capacitor ( $C_{\mathrm {LS}}$ ) at the RA output, such that the RA bandwidth can be improved. Furthermore, instead of a single-level shift in the prior arts, the DACLS ring amplifier provides an option for multiple level shifts and thereby accomplishes a greater RA gain error reduction. In addition, a customized bypass-window scheme is applied, which can skip some power-wasting digital-to-analog converter (DAC) switchings by window detection and thus reduces the power consumption of the ADC. To reduce the bit-cycling time of the SAR conversion, a delay-reduced (DR) SAR logic is introduced to increase the ADC speed. The ADC chip is fabricated in 28-nm CMOS technology and occupies an active area of 0.013 mm2. At 130-MS/s and the Nyquist-rate input frequency, the measured SNDR is 72.5 dB, while the power consumption is only 0.82 mW. Without any calibration, the proposed ADC achieves a Walden and a Schreier figure-of-merit (FoM) of 1.8 fJ/conversion step and 181.5 dB, respectively. Compared to the prior-art ADCs with an input bandwidth ≥ 40 MHz and a SNDR > 68 dB, this work shows the best FoMs.


  • Fixed-Switching-Frequency Background Capacitor-Current-Sensor Calibration for DC–DC Converters

    by Yi-Wei Huang, Tai-Haur Kuo

    Background capacitor-current-sensor (CCS) calibration (CAL) is proposed for dc–dc converters to achieve fast load-transient response for small undershoot $V_{\mathrm {US}}$ , overshoot $V_{\mathrm {OS}}$ , and short settling time $t_{\mathrm {S}}$ in the output voltage $V_{\mathrm {O}}$ . The CCS’ impedance $Z_{\mathrm {Cs}}$ is calibrated to a scaled replica of the output capacitor’s impedance $Z_{\mathrm {Co}}$ , which varies with printed-circuit-board parasitics, process-voltage-temperature variations, and aging. Thus, the CCS shunts a current $I_{\mathrm {Cs}}$ equal to a scaled output-capacitor current $I_{\mathrm {Co}}$ , which instantly and accurately reflects load-current $I_{\mathrm {load}}$ transients. The CAL operates at a fixed switching frequency $f_{\mathrm {SW}}$ . At this $f_{\mathrm {SW}}$ , although $Z_{\mathrm {Cs}}$ is dominated by its inductive part, this work can still calibrate its capacitive and resistive parts based on the time derivatives dV O / dt and dI Cs / dt , respectively. This fixed- $f_{\mathrm {SW}}$ CAL overcomes the bottleneck of the prior state-of-the-art CCS CAL, which must hop $f_{\mathrm {SW}}$ to lower values to calibrate $Z_{\mathrm {Cs}}$ capacitive and resistive parts, thereby enlarging $V_{\mathrm {O}}$ steady-state ripples and transient fluctuations during CAL. Thus, only this fixed- $f_{\mathrm {SW}}$ CAL is suitable for background operation. Moreover, this CAL can be interrupted by a load-transient or dynamic-voltage-scaling event and be reactivated in quasi-steady state. The shortest CAL period is 8.8 $\mu \text{s}$ at $f_{\mathrm {SW}} = 30$ MHz without interruption. A buck converter with this CCS CAL is fabricated in 0.18- $\mu \text{m}$ CMOS process and occupies 2.25 mm 2 . Under a 2-A/4-ns step-up (step-down) load transient, the measured $V_{\mathrm {US}}$ ( $V_{\mathrm {OS}}$ ) and $t_{\mathrm {S}}$ are 36 mV (29 mV) and 56 ns (45 ns), respectively. Compared with prior state of the arts, this work achieves much smaller $V_{\mathrm {O}}$ ripples and fluctuations during CAL, shorter CAL period, and faster load-transient response.


  • A 0.4-mA-Quiescent-Current, 0.00091%-THD+N Class-D Audio Amplifier With Low-Complexity Frequency Equalization for PWM-Residual- Aliasing Reduction

    by Yi-Zhi Qiu, Shih-Hsiung Chien, Tai-Haur Kuo

    This article proposes a low-complexity frequency equalization technique for pulsewidth modulation (PWM)-residual-aliasing reduction in closed-loop Class-D audio amplifiers to achieve both low total harmonic distortion plus noise (THD+N) and low quiescent current. Based on the comprehensive analysis on the phase shift delay between the audio input and the loop filter’s output for the prior PWM-residual-aliasing reduction technique, the proposed technique minimizes the non-idealities via a frequency-equalization path to enhance the cancellation ability of high-frequency PWM switching components. In this way, the PWM-residual-aliasing distortion is greatly suppressed, thereby permitting Class-D audio amplifiers to achieve a further-reduced THD+N for the entire audio band while operating at a low switching frequency ( $f_{\mathrm {SW}}$ ), leading to less quiescent current consumption. Moreover, due to the minimized phase shift delay, the required bias current of the loop filter’s first operational amplifier for the target THD+N can be reduced, resulting in even lower quiescent current. Compared with other state of the arts, this work’s high-fidelity second-order Class-D audio amplifier, fabricated with cost-efficient 0.5- $\mu \text{m}$ CMOS technology, not only achieves a competitive minimal THD+N of 0.00091% for a 1-kHz input as well as the lowest maximal THD+N of 0.0027% over the entire audio band while operating at a low $f_{\mathrm {SW}}$ of 168 kHz but also features both the highest figure of merit (FOM) of 2536 and the lowest quiescent current of 0.4 mA, surpassing the prior arts by a factor of 2.3.


  • A 10-GS/s NRZ/Mixing DAC With Switching-Glitch Compensation Achieving SFDR >64/50 dBc Over the First/Second Nyquist Zone

    by Hung-Yi Huang, Xin-Yu Chen, Tai-Haur Kuo

    This article presents a high-linearity wide-bandwidth current-steering digital-to-analog converter (DAC). To overcome the code-dependent current-switching glitch effect, which seriously degrades the DAC linearity, a switching-glitch compensation (SGC) technique, which is realized with glitch duplicators, is proposed to generate a complementary amount of switching glitch at the DAC output. Hence, the amount of switching glitch at the DAC output becomes code-independent, thus improving the linearity of the DAC output. In addition, a decorrelator is proposed to randomize the mismatch effect of the glitch duplicators, thus eliminating the mismatch-induced spur at the DAC output spectrum. A 14-bit 10-GS/s non-return-to-zero (NRZ)/Mixing DAC with SGC is realized in 28-nm CMOS. Measurement results show that the spurious free-dynamic range (SFDR) is improved up to around 20 dB by the SGC. Therefore, this DAC with SGC achieves an SFDR >64 dBc over the entire first Nyquist zone and >50 dBc over the entire second Nyquist zone. Compared to prior state-of-the-art CMOS DACs with an output frequency $(f_{\mathrm {out}}) \ge3.4$ GHz, this DAC with SGC achieves a 12.5-dB better SFDR with $f_{\mathrm {out}}$ near 10 GHz and a 1.4x higher $f_{\mathrm {out}}$ with an SFDR larger than 50 dBc.


  • A 3 mW 6-bit 4 GS/s Subranging ADC With Subrange-Dependent Embedded References

    by Chung-Ming Yang, Tai-Haur Kuo

    A subranging analog-to-digital converter (ADC) with reference-embedded comparators (RECs) is proposed. By adjusting the bias current and/or body voltage of the REC's input differential pair, the REC offset can be adjusted to a specific voltage equal to a reference voltage referred to henceforth as the embedded reference. For the ADC's coarse stage, RECs with wide-range embedded references are implemented by adjusting the bias currents using current source arrays to cover the full-scale input. By contrast, for the ADC's fine stage, RECs with narrow-range embedded references are implemented by adjusting the body voltage. In addition, the centers of the embedded references in the different ADC subranges are created by current source arrays, which are digitally scaled according to the coarse ADC's output codes. As a result, the reference-voltage-switching network used in conventional subranging ADCs is not required, and hence the speed of the ADC is increased. Moreover, to eliminate the effects of process variation, the bias currents and body voltages in the RECs are calibrated with an auxiliary resistor ladder. After the calibration, the resistor ladder is removed. Consequently, no resistor ladder is used during normal operation, which greatly saves power. A 3 mW 6-bit 4 GS/s REC-based subranging ADC is implemented in 28-nm CMOS technology. With a near Nyquist frequency input, the ADC achieves SNDRs of 31.8 dB and 30.7 dB at 3.6 GS/s and 4 GS/s, respectively. Moreover, at 3.6 GS/s, the ADC has a Walden Figure-of-Merit (FoM W ) of 22.7 fJ/conv-step, which is the best compared with prior state-of-the-art 6-bit high-speed ADCs.


  • Transient Output-Current Regulator With Background Calibration Applied to a Buck Converter for Fast Load-Transient Response

    by Yi-Wei Huang, Ting-Yu Yu, Tai-Haur Kuo

    A transient output-current regulator (TOCR) is presented and merged into a buck converter to achieve fast load-transient response for stepwise load-current Iload profiles, leading to small undershoot/overshoot voltage VUS/VOS and short settling time tS in the output voltage VO. The TOCR instantly detects an Iload transient and triggers a compensation current IU/ID. Moreover, background calibration of the IU/ID is proposed to ensure the sum of inductor current IL and IU/ID accurately tracks Iload under PVT variations. The prototype chip, fabricated in a 0.18-μm CMOS process, occupies 1.89 mm2. Under 0.45-A and 1-A Iload transients, the measured VO remains within 1% of its nominal 1.8 V, with VUS and VOS both being less than 18 mV and a negligible tS. Compared with other state of the arts, this work achieves the fastest load-transient response with the smallest VUS/VOS and shortest tS.


  • A Calibration-Free 14-b 0.7-mW 100-MS/s Pipelined-SAR ADC Using a Weighted- Averaging Correlated Level Shifting Technique

    by Jia-Ching Wang, Tsung-Chih Hung, Tai-Haur Kuo

    This article presents a 14-b 100-MS/s single-channel pipelined-successive-approximation register (SAR) ADC using a weighted-averaging correlated level shifting (WACLS) technique. For a closed-loop residue amplification, the error voltage due to the finite operational amplifier (opamp) gain can be ideally removed by the proposed WACLS technique with a low-gain opamp. In addition, the opamp bandwidth degradation, by an extra level-shift capacitor (CLS) in two-phase amplification CLS-based circuits, can be relaxed and minimized in WACLS. Furthermore, a speed-enhancement scheme is provided to alleviate the speed degradation owing to one extra amplification phase and long bit-cycling time from two-phase amplification and SAR circuits, respectively. A modified reference swapping (RS) technique is applied to diminish the capacitor mismatch error without any calibration. A quick startup ring amplifier design is introduced for duty-cycled control power saving. The chip is implemented in the 28-nm CMOS technology and occupies an active area of 0.018 mm². At 100 MS/s and Nyquist-rate input, the measured SNDR is 71.7 dB with 0.7-mW power consumption only. The calibration-free ADC achieves Walden and Schreier figure-of-merit of 2.2 fJ/conversion-step and 180.2 dB, respectively. Compared with the prior-art ADCs with sampling frequency > 100 MS/s and SNDR > 65 dB, this work advances the state-of-the-art by 3x and 5.3 dB, respectively.


  • A 0.07-mm2 162-mW DAC Achieving >65 dBc SFDR and < −70 dBc IM3 at 10 GS/s With Output Impedance Compensation and Concentric Parallelogram Routing

    by Hung-Yi Huang, Tai-Haur Kuo

    A digital-to-analog converter (DAC) with small-size non-cascoded current cells is proposed to achieve small area, low-power consumption, and high linearity over a wide bandwidth. An output impedance compensation (OIC) technique using a compensation resistor, implemented by a PMOS with code-dependent gate voltage control, is proposed to remedy the nonlinearity induced by the insufficient output impedance of the non-cascoded current cells. In addition, a proposed concentric parallelogram routing (CPR) technique, in which the subcells of each current cell are arranged such that they form a parallelogram shape with a common centroid, is used to reduce both the mismatch error and the routing-induced timing skew among the current cells. The DAC, implemented in a 28-nm CMOS process, achieves >65-dBc spurious-free dynamic range (SFDR) and <; -70-dBc third-order intermodulation distortion (IM3) over the entire Nyquist bandwidth at 10 GS/s while consuming 162 mW from a single 1.1 V supply.


  • A Reconfigurable and Extendable Single-Inductor Single-Path Three-Switch Converter for Indoor Photovoltaic Energy Harvesting

    by Peng-Chang Huang, Tai-Haur Kuo

    This article proposes a single-path three-switch (1P3S) single-inductor dual-input dual-output (SIDIDO) converter to manage power among a photovoltaic (PV) module, battery, and load for indoor PV energy harvesting. For low duty-cycle applications, the 1P3S converter increases efficiency in the PV-to-battery-to-load path by eliminating inductor-sharing power switches. This article also proposes a reconfigurable controller to achieve reconfigurability and extendibility that the 1P3S converter can be reconfigured as a dual-path three-switch (2P3S) SIDIDO converter, combined as a dual-path six-switch (2P6S) SIDIDO converter, or extended as a paralleled-1P3S converter for high energy efficiency in various applications with different PV and load power profiles. To identify each converter's advantageous applications, the efficiencies of the 1P3S, reconfigured 2P3S, and combined 2P6S converters were analyzed under dynamic PV and load powers. The chip is fabricated in the 0.5-μm CMOS process with a 1.24-mm² chip area. The measured peak efficiencies for the 1P3S, 2P3S, and 2P6S converters are 95.0%, 95.2%, and 90.0%, respectively, while the measured quiescent currents are 210, 130, and 140 nA, respectively. Compared with the state-of-the-art 2P3S and 2P6S converters, the reconfigured 2P3S and combined 2P6S converters with the proposed IC, respectively, achieve higher efficiency through appropriate switch sizes and on-time optimizations.