SMShan Ma

Shan Ma

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Shan Ma has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Unsteady characteristics analysis of compressors based on the proper orthogonal decomposition method

    by Shan Ma, Xiaolin Sun, Lin Cheng, Yang Yu, Wen Cheng

    An aero-engine is often accompanied by a strong unsteady flow at near-stall condition, and increasing unsteady airflow eventually makes the engine unstable. To explore the unsteady flow characteristics, the Rotor 37 was taken as the research object. The unsteady flow characteristics of the blade tip flow field were analyzed using numerical simulation. The proper orthogonal decomposition (POD) was used to reconstruct the blade field, and the flow characteristics were analyzed. The results indicate that the unsteady characteristics of the tip area are mainly caused by the periodic evolution of the tip leakage vortex (TLV) and tip secondary vortex (TSV), and the interaction between the shock wave and tip leakage flow (TLF) plays a dominant role. The unsteady dominant frequency of the flow field upstream of the leading edge (LE) is consistent with the pressure surface and is ∼0.47 times the blade passing frequency (BPF), which is the main flow frequency. The first four POD modes can reconstruct the flow field well and successfully capture the high-energy pulsation structure in the upstream of the blade and the pressure surface flow field of the LE. The modes 1–2 frequencies are ∼0.48 times BPF, which is basically consistent with the conclusion of the prototype flow field and indicates that the periodicity of the TLV and TSV plays a leading role. The modes 3–4 frequencies are ∼0.96 times BPF, which captures the flow fluctuation near the LE. This fluctuation position is consistent with the TLV and reflects the low speed caused by the TLF.

  • Open Access

    Experimental investigation on periodic characteristics of high-frequency oblique slot plasma synthetic jet actuator

    by Lin Cheng, He-Xia Huang, Xiao-Lin Sun, Shan Ma, Hui-Jun Tan

    A plasma synthetic jet actuator with a high-frequency oblique slot was designed for supersonic flow control. The actuator's periodic operation characteristics were investigated using electrical parameter measurements and high-speed schlieren techniques. Experimental findings indicate that the actuator can stably operate within the frequency range of 0–2400 Hz. With increasing operating frequency, the breakdown voltage, maximum current, and discharge energy decrease, while the energy efficiency of the discharge increases. Moreover, the experiment revealed for the first time that an increase in the number of charged particles within the cavity leads to a decrease in breakdown voltage, and the concentration of charged particles reaches saturation at approximately 1200 Hz. High-speed schlieren observations indicate substantial inter-cycle influences in the periodic jet. At higher operating frequencies, the impact of inter-cycle flow field effects becomes more pronounced. The oblique slot plasma synthetic jet exhibits clear directionality in the distribution of shock waves and jet. The oblique slot jet also shows a significant wall attachment effect. These characteristics are beneficial for enhancing the flow control capability of the actuator. At 1200 Hz, the actuator achieves a discharge efficiency of 63% and a maximum jet front velocity of 309 m/s, showcasing its superior overall performance.


  • Open Access

    Experimental characterization of a modified high-speed plasma synthetic jet actuator with oblique-slot exit

    by Lin Cheng, He-Xia Huang, Xiao-Lin Sun, Shan Ma, Hui-Jun Tan

    In the field of flow control research, oblique jets are known to offer several advantages over vertical jets. To gain a comprehensive insight into the flow field characteristics of a plasma synthetic jet actuator with an oblique-slot exit, the related experiments are conducted. The experiment employed high-speed schlieren imaging techniques and electrical parameter measurements to acquire the flow field characteristics and discharge properties of the oblique-slot actuator, followed by a comparative analysis with a vertical circular orifice actuator. The oblique-slot plasma synthetic jet exhibits a wall-attaching effect and asymmetric flow characteristics, which differ from those of the vertical circular orifice actuator. The actuator generates a wall jet with an initial velocity of 389.5 ± 15.08 m/s, effectively propelling the fluid within the boundary layer. The Mach number of the precursor shock wave in the direction of the jet reaches 1.59, but decreases to just 1.02 in the opposite direction. Over a period in the range of 10–70 μs, the Froude number of the plasma jet decreases from 1841 to 238. The dominant role of the inertial force gradually weakens, while the influence of buoyancy increases, causing the jet boundary to move upward. The oblique-slot jet configuration represents a typical planar jet, exhibiting superior flow control uniformity compared with the vertical circular orifice jet. The results indicate that the high-speed oblique-slot plasma synthetic jet actuator designed in this study possesses distinct advantages over vertical circular orifice actuators for high-speed fluid flow control.


  • Open Access

    A New Segmented Suction Slot Design Based on the Performance of Compressor Cascade

    by Fengming Li, Ganchao Zhao, Lu Ye, Dongfeng Yan, Shan Ma

    To develop an effective suction slot arrangement, computational fluid dynamics simulation software and a high subsonic compressor cascade were used to simulate different suction slots. Based on the effects of various suction slots on the cascade performance under various operating conditions, a novel segmented suction slot structure Seg3 was proposed. The results of the study revealed that in the vicinity of the operating conditions ( ), a full-blade height suction slot should be installed at least 5% of the chord length downstream of the corner separation point to effectively remove the separation. For small and medium incidences, the best performance was observed for suction slot SS5, which was located at 60% of the chord length downstream of the leading edge. Analyzing the effects of SS5 and Seg3 on the cascade performance revealed that when the incidence was less than 4°, the reductions in the total pressure loss coefficients for ζsuc of SS5 and Seg3 both exceeded 8.2%. When the incidence was 4° or greater, the ζsuc increased slightly for SS5, whereas it decreased for Seg3, and the ζsuc was reduced. For a 3° incidence, for example, Seg3 reduced the ζsuc and passage blockage by 12.74% and 8.41%, respectively, and increased the static pressure rise coefficient by 18.55% from the baseline values. Thus, the segmented suction slot proposed in this paper outperformed conventional full-blade height suction slots.


  • Open Access

    Influence of a Wavy Blade-End Applied in an Axial Compressor Cascade on the Secondary Flow of the Passage

    by S. Ma, F. Li, L. Gui, D. Chen, T. Duan

    To improve the compressor performances at variable conditions, in this research, we used numerical simulation software to analyze and discuss the effects of three kinks of a wavy blade-end on an axial compressor cascade. One of the wavy blade-ends was a traditional structure with a wavy leading edge and a trailing edge (WBE_P). The other two wavy blades were new structures with a straight trailing edge and a wavy leading edge (WBE_R, WBE_S). The difference between WBE_R and WBE_S was that the blade profile used to form the wavy blade was different. For WBE_R, we obtained the wavy leading edge by rotating the element at different heights, and the trailing edge was the center of a circle. For WBE_S, we obtained the wavy leading edge by using a new element with a different camber angle. Because of the new geometry involving some discussions of a variety of parameters, we further discussed the geometric parameters and structure to guide the design and optimization of the blade. We drew some conclusions at the stable condition (6° incidence). For the first case (WBE_P), when the wavelength of the wavy blade-end was increased to 0.3 times the blade height, the total pressure loss was enhanced. When the wavelength was 0.2 times the blade height, the amplitude was 0.06 times the pitch, the minimum area of blocked range (Ab) and the total pressure loss coefficient ζ could be obtained, and the ζ and Ab were decreased by 5.49%, and 12.72% compared with the baseline. Furthermore, to weaken the influence of changed blade profile on the exit airflow angle, we proposed WBE_P and WBE_R with new structures. We further improved the flow-field characteristics of WBE_P by WBE_R, and the ζ and Ab decreased by 5.84% and 13.79% compared with the baseline. Additionally, the stall point was delayed from 7.5° to 7.7° incidence. Therefore, the wavy blade-end applied in the leading edge had a greater contribution to improving the flow characteristic, and the straight trailing edge was beneficial to maintaining the exit flow angle. WBE_S with a smoother blade surface did not show an advantage compared with WBE_R. WBE_R with a wavy blade-end leading edge and a straight trailing edge showed an advantage in improving the cascade performance, which was suitable for use in the stator from the last stage of a high-load axial compressor.

  • Influences of key parameters on flow features in the curved ducts with equal area

    by Xiao-Lin Sun, Shan Ma

    Curved ducts are widely used in aircraft engines to improve some capability of aero-engines. Complex internal flow characteristics would be induced by the curvature in such components. In this study, the influence of parameters, including the arc angle α, the curvature radius R i, and the height H, on the local accelerating and transonic flow in the curved ducts with equal area were studied numerically and theoretically under different nozzle pressure ratios (NPRs). The range of the Re number based on the height of the duct and the velocity at the inlet was [ ] ∼ [ ]. The shear stress transport κ-ω turbulent model was proved by the test data to suitably simulate the flow field in curved ducts because it could accurately predict the flow separations under adverse pressure gradients. The uncertainty of the pressure scan value to obtain the test data was ±0.05%. Numerical results showed that the effect of α on the flow characteristics of the curved ducts is little. The maximum Ma number in the curved section reduces with the increase of R i, and that grows with the increase of H. The range of the maximum Ma number was 1.20∼1.80. The critical NPRs, which decided the special flow features, were found in the curved ducts. The critical NPR rises with the increase of R i; however, the effect of H on the critical NPR is irregular due to the flow separations located near the lower wall induced by the large adverse pressure gradient. The theoretical results based on the small perturbation theory of transonic flow in the polar coordinate system proved that the distribution of sonic line was just dependent on the inner diameter R1, the outer diameter R2, and the arc angle θmax of the curved section. The critical mass flow and the critical NPR2 are only related to R1 and R2.


  • Optimization study on the influence of little blades’ spatial position on a compressor cascade performance

    by Shan Ma, Xiaolin Sun

    To reveal the importance of little blades’ spatial position to improve the cascade performance at different condition, the pitchwise and axial direction of the little blades on the end-wall are adopted as the optimization variables to complete a double-objective optimization. Meanwhile, the three-dimensional flow field characteristics of the cascade with and without little blades are analyzed comparatively. The study found that as the optimal solutions are obtained at the three bigger incidences (3°, 5°, and 7°), the optimal position is always close to the leading edge of blade and far away from the blade suction surface, and the more intuitive design suggestions are given in this article. Moreover, at the near design conditions (−1°, 0°, and 1°), little blades increase the total pressure loss and reduce the static pressure, which are considered unsuitable for improving the cascade performance. If the stable operation range are the main performance indicators, the optimization of the little blades’ spatial position should be completed at the near stall condition (7° incidence). If the conditions with mid-range incidences (2°< i Opt_Act3, Opt_Act5, and Opt_Act7), the induced vortices resist the effect of axial reverse pressure gradient and pass through the blade passage, which is the main reason for the total pressure loss reduction. Appropriate spatial position of little blades not only strengthens the capability to prevent the low-energy fluids accumulating in the corner region near the end-wall, but exhibits sufficient advantage to weaken the boundary layer.


  • Applications of little blades in a high-load compressor cascade with leaned blade

    by Shan Ma, Xiaolin Sun

    The development of boundary layer affects the compressor cascade performance to a certain extent. Therefore, the compound lean and little blades are selected to redistribute the boundary layer, and the influences of these two flow control technologies on the axial compressor cascade performance are further studied. The calculated results showed that appropriate high pressure region on the blade suction surface near the end-wall is helpful to reduce the total pressure loss of compressor cascade, which can be achieved by positive lean technique. Meanwhile, the maximum stable operation boundary can be expanded by the application of positive leaned blade. On the other hand, the introduction of negative lean angle not only increases the total pressure loss of cascade, but reduces the stable operation range. As the little blades are introduced in the negative lean compressor cascade, the stable operation range is significantly improved by the introduction of little blades. Especially the cascade with −10° lean angle, the maximum stable operation boundary is increased from 1° to 6°. In the positive lean compressor cascade, although more low-energy fluid is accumulated on the blade suction surface near the mid-span, the little blades still show an active role in reducing the total pressure loss and expending the stable operation range, because the influence range of induced vortex reaches 30%span. The results provide a reference for improving the aerodynamic performance of compressor stator, especially when more low-energy fluid is blocked in the range near the mid-span.


  • Effects of segmented layer suction and micro-vortex generator on a high-load compressor cascade performance

    by Shan Ma, Wuli Chu, Xiaolin Sun, Zhengtao Guo, Song Yan

    The axial location of full-span boundary layer suction is studied to explore the influences of suction slot on the cascade performance. At the design condition, the slot with 50% axial location shows a superior capability to reduce the total pressure loss. At the near stall condition, the more upstream of the suction slot is moved, the more total pressure loss is reduced, and the suction slot with a location of 0.7 axial chord length cannot effectively reduces the total pressure loss in all conditions. Moreover, a rearranged segmented suction slot according to the distribution characteristics of the flow reversal region is developed and compared with full-span boundary layer suction. The segmented suction slot shows significant advantages in delaying the stall occurrence, and the stall point is delayed from 7.9° to 10.0° compared with the baseline. According to a quantitative analysis method selected to measure the performances of flow control technologies, the wake loss is significantly reduced by the segmented suction slot. Finally, a set of micro-vortex generator is introduced in the cascade with a segmented suction slot, and the conclusion indicates that the portion near the end-wall is very effective to reduce the flow loss.


  • Compressible flow characteristics in bent duct with constant flow section

    by Xiao-Lin Sun, Shan Ma, Zhan-Xue Wang, Jing-Wei Shi, Li Zhou

    The components with large curvature features are widely applied in aero-engines. Complex flow features are induced due to large curvature under high-subsonic even transonic incoming flow condition. In this study, the formation mechanisms of local acceleration in bent duct are investigated. To this end, the cold fluid test of a 60° bent duct with constant flow section was conducted. The surface static pressures and the schlieren flow visualizations were obtained. Then the three-dimensional numerical simulations based on the experimental model were computed using computational fluid dynamics software. The simulations were conducted using five different turbulence models to compare with the experimental data. The validation study shows that the shear stress transfer (SST) κ-ω turbulence model is suitably used for the simulations. Results show that three different flow situations were shown for the bent duct at diverse nozzle pressure ratios (NPRs). One situation was shown by the case at NPR = 1.5, in which the whole flow field is subsonic, and just two jet edges are shown by the schlieren images. One situation was shown by the case at NPR = 1.8, in which a local supersonic region is induced near the lower wall at the hind side of the bent section, and a small shock wave is observed. The other one situation was shown by the cases at NPR = 2.0, 2.5 and 3.0, in which the air flow in the whole passage reaches supersonic speeds and an oblique shock wave is shown for each case.