Jae Won Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jae Won Kim has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Hyungsu Jang
Department of Energy Engineering, Ulsan National Institute of Science and Technology (UNIST), Ulsan 44919, South Korea
2 shared publications - Jin Young Kim
School of Energy and Chemical Engineering, Ulsan National Institute of Science and Technology (UNIST), Ulsan 44919, Republic of Korea
2 shared publications - Yung Jin Yoon
Department of Energy Engineering, Ulsan National Institute of Science and Technology (UNIST), Ulsan 44919, South Korea
2 shared publications - Bright Walker
Department of Chemistry Kyung Hee University Seoul Republic of Korea
1 shared publication - Dong Suk Kim
Korea KIER-UNIST Advanced Center for Energy, Korea Institute of Energy Research (KIER), Ulsan 44919, South Korea
1 shared publication - Gi-Hwan Kim
Perovtronics Research Center and Department of Energy Engineering, Ulsan National Institute of Science and Technology (UNIST), Ulsan 44919, South Korea
1 shared publication
Latest Publications
- 15 March 2019
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 7 (15) , 4559-4566
Synergistic combination of amorphous indium oxide with tantalum pentoxide for efficient electron transport in low-power electronics
Among transparent metal oxide semiconductors, systems based on indium oxide currently deliver the best combination of electronic characteristics and optical transmittance, outperforming even the well-established polycrystalline silicon devices. Indium oxide has the unique property that uniform, amorphous films yield superior electronic properties compared to microcrystalline films; for this reason, Ga and Zn hetero-elements are usually added to disrupt crystallization and result in uniformly disordered films. However, dopants have a general tendency to increase the complexity and decrease the mobility of semiconductors and their addition might well be avoided if high-quality, amorphous In2O3 films could be grown without them. In this work, we show that this problem can be resolved by exploiting a synergistic interaction between solution-processed indium oxide (In2O3) and underlying tantalum pentoxide (Ta2O5) dielectric films. We observed that amorphous Ta2O5 inhibits crystallization of In2O3 leading to high-quality amorphous thin films with reduced oxygen deficiencies at the semiconductor/dielectric interface. Transparent Ta2O5/In2O3 TFTs with very low operating voltages were demonstrated with effective field-effect mobilities of up to 23.1 cm2 V−1 s−1 at only 3 V drain–source voltage (VDS) using this approach. Additionally, the suppressed carrier density arising from reduced oxygen deficiencies reduced the drain current at 0 V gate bias (I0) by six orders of magnitude from 0.25 mA to 10.8 nA, compared to a SiO2 reference device. These results highlight the importance of considering an underlying dielectric layer to maximize device performance.
- 15 March 2019
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 7 (15) , 4559-4566
Synergistic combination of amorphous indium oxide with tantalum pentoxide for efficient electron transport in low-power electronics
Among transparent metal oxide semiconductors, systems based on indium oxide currently deliver the best combination of electronic characteristics and optical transmittance, outperforming even the well-established polycrystalline silicon devices. Indium oxide has the unique property that uniform, amorphous films yield superior electronic properties compared to microcrystalline films; for this reason, Ga and Zn hetero-elements are usually added to disrupt crystallization and result in uniformly disordered films. However, dopants have a general tendency to increase the complexity and decrease the mobility of semiconductors and their addition might well be avoided if high-quality, amorphous In2O3 films could be grown without them. In this work, we show that this problem can be resolved by exploiting a synergistic interaction between solution-processed indium oxide (In2O3) and underlying tantalum pentoxide (Ta2O5) dielectric films. We observed that amorphous Ta2O5 inhibits crystallization of In2O3 leading to high-quality amorphous thin films with reduced oxygen deficiencies at the semiconductor/dielectric interface. Transparent Ta2O5/In2O3 TFTs with very low operating voltages were demonstrated with effective field-effect mobilities of up to 23.1 cm2 V−1 s−1 at only 3 V drain–source voltage (VDS) using this approach. Additionally, the suppressed carrier density arising from reduced oxygen deficiencies reduced the drain current at 0 V gate bias (I0) by six orders of magnitude from 0.25 mA to 10.8 nA, compared to a SiO2 reference device. These results highlight the importance of considering an underlying dielectric layer to maximize device performance.
- 24 September 2018
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 6 (41) , 20138-20144
The introduction of a perovskite seed layer for high performance perovskite solar cells
Processing for obtaining compact and uniform perovskite photoactive layers has been intensively studied over the last few years to achieve high power conversion efficiencies (PCEs) in solar cells. Particularly, high quality crystal growth of perovskite layers is critical to enhance device performance. We demonstrate an easy and effective new process for high efficiency p–i–n planar heterojunction structures of perovskite solar cells (PeSCs) by using a compact seed perovskite layer (CSPL). The CSPL assists vertical growth of perovskite crystals and obtains the highly crystalline perovskite photoactive layer, which leads to the reduction in the charge transfer resistance and a longer photoluminescence lifetime. The PeSC device with a CSPL shows a remarkably improved PCE, from 15.07% to 19.25%, with a record open circuit voltage (VOC) of 1.16 V in the p–i–n structure with pure crystal perovskite and negligible current density–voltage hysteresis. Additionally, a PCE of 20.37% was achieved in CSPL assisted n–i–p structure PeSCs.
- 24 September 2018
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 6 (41) , 20138-20144
The introduction of a perovskite seed layer for high performance perovskite solar cells
Processing for obtaining compact and uniform perovskite photoactive layers has been intensively studied over the last few years to achieve high power conversion efficiencies (PCEs) in solar cells. Particularly, high quality crystal growth of perovskite layers is critical to enhance device performance. We demonstrate an easy and effective new process for high efficiency p–i–n planar heterojunction structures of perovskite solar cells (PeSCs) by using a compact seed perovskite layer (CSPL). The CSPL assists vertical growth of perovskite crystals and obtains the highly crystalline perovskite photoactive layer, which leads to the reduction in the charge transfer resistance and a longer photoluminescence lifetime. The PeSC device with a CSPL shows a remarkably improved PCE, from 15.07% to 19.25%, with a record open circuit voltage (VOC) of 1.16 V in the p–i–n structure with pure crystal perovskite and negligible current density–voltage hysteresis. Additionally, a PCE of 20.37% was achieved in CSPL assisted n–i–p structure PeSCs.