Eric Ng
Eric Ng has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Ahmed Ben Ayed
Department of Electrical and Computer Engineering, University of Waterloo, Waterloo, ON, Canada
2 shared publications - Patrick Mitran
Department of Electrical and Computer Engineering, University of Waterloo, Waterloo, Canada
2 shared publications - Slim Boumaiza
University of Waterloo
2 shared publications - Giovanni Scarlato
RF/MMIC Group, Department of Electrical and Computer Engineering, University of Waterloo, Waterloo, ON, Canada
1 shared publication - Yehia Beltagy
Department of Electrical and Computer Engineering, University of Waterloo, Waterloo, ON, Canada
1 shared publication
Latest Publications
- Open Access
- 13 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 100627-100636
Digital Predistortion of Millimeter-Wave Hybrid Beamforming Transmitters Using Observation Receivers With Low-Bit Resolution Analog-to-Digital Converter
This paper proposes a new digital predistortion (DPD) scheme for linearizing millimeter-wave hybrid beamforming transmitters using observation receivers with low-bit resolution analog-to-digital converters (ADCs). To train the DPD function required to compensate for the distortions exhibited by a given sub-array (also called main sub-array), an error signal is produced by out-of-phase combining the main sub-array transmitted signal and the one generated by another sub-array (also called auxiliary sub-array) using anti-beamforming modules. The error signal is then frequency down-converted and digitized using a low-bit resolution ADC. Proof-of-concept validation experiments are conducted by applying the proposed DPD system to linearize an off-the-shelf hybrid-beamforming array comprised of four 64-element sub-arrays, operating at 28 GHz and driven with up to 800 MHz orthogonal frequency-division multiplexing modulated signals. Using the proposed DPD scheme, an observation receiver with a 4-bit ADC was sufficient to improve the adjacent channel power ratio by 10 dB and the error vector magnitude was reduced from 5.8% to 1.6%. These results are similar to those obtained using an observation receiver with 16-bit ADC.
- 13 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 100627-100636
Open AccessDigital Predistortion of Millimeter-Wave Hybrid Beamforming Transmitters Using Observation Receivers With Low-Bit Resolution Analog-to-Digital Converter
This paper proposes a new digital predistortion (DPD) scheme for linearizing millimeter-wave hybrid beamforming transmitters using observation receivers with low-bit resolution analog-to-digital converters (ADCs). To train the DPD function required to compensate for the distortions exhibited by a given sub-array (also called main sub-array), an error signal is produced by out-of-phase combining the main sub-array transmitted signal and the one generated by another sub-array (also called auxiliary sub-array) using anti-beamforming modules. The error signal is then frequency down-converted and digitized using a low-bit resolution ADC. Proof-of-concept validation experiments are conducted by applying the proposed DPD system to linearize an off-the-shelf hybrid-beamforming array comprised of four 64-element sub-arrays, operating at 28 GHz and driven with up to 800 MHz orthogonal frequency-division multiplexing modulated signals. Using the proposed DPD scheme, an observation receiver with a 4-bit ADC was sufficient to improve the adjacent channel power ratio by 10 dB and the error vector magnitude was reduced from 5.8% to 1.6%. These results are similar to those obtained using an observation receiver with 16-bit ADC.
- 16 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 67 (11) , 4479-4492
Digital Predistortion of Millimeter-Wave RF Beamforming Arrays Using Low Number of Steering Angle-Dependent Coefficient Sets
This paper proposes a single-input single-output (SISO) digital predistortion (DPD) model for linearizing millimeter-wave (mm-wave) RF beamforming arrays. It starts with a dual-input power amplifier (PA) model that accounts for steering angle-dependent load modulation effects. This dual-input model is then transformed into a SISO model under the assumption of weak PA nonlinearity and RF beamforming architecture. The underlying coefficients of the SISO array model incorporate the beamforming weights, antenna cross-coupling, channel coefficients, and any possible phase-shifter gain variation with phase shift setting. An over-the-air (OTA) measurement setup is finally developed to validate the capacity of a SISO DPD model to linearize two different arrays-under-test with 4 and 64 elements and radiating mm-wave modulated signals with 320- and 800-MHz bandwidth. Although, in principle, the DPD coefficients should be retrained for each steering angle, experimental results have shown that the same set of coefficients can be used over a wide range of steering angles, and only a few sets of trained DPD coefficients are sufficient to minimize the distortion in a mm-wave RF beamforming array across a 120° steering range.
- 16 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 67 (11) , 4479-4492
Digital Predistortion of Millimeter-Wave RF Beamforming Arrays Using Low Number of Steering Angle-Dependent Coefficient Sets
This paper proposes a single-input single-output (SISO) digital predistortion (DPD) model for linearizing millimeter-wave (mm-wave) RF beamforming arrays. It starts with a dual-input power amplifier (PA) model that accounts for steering angle-dependent load modulation effects. This dual-input model is then transformed into a SISO model under the assumption of weak PA nonlinearity and RF beamforming architecture. The underlying coefficients of the SISO array model incorporate the beamforming weights, antenna cross-coupling, channel coefficients, and any possible phase-shifter gain variation with phase shift setting. An over-the-air (OTA) measurement setup is finally developed to validate the capacity of a SISO DPD model to linearize two different arrays-under-test with 4 and 64 elements and radiating mm-wave modulated signals with 320- and 800-MHz bandwidth. Although, in principle, the DPD coefficients should be retrained for each steering angle, experimental results have shown that the same set of coefficients can be used over a wide range of steering angles, and only a few sets of trained DPD coefficients are sufficient to minimize the distortion in a mm-wave RF beamforming array across a 120° steering range.