GBGoknur Bayram

Goknur Bayram

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Goknur Bayram has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • PMMA-based electrospun composite fibers for dye adsorption from water

    by İlKnur Çakar, Sertan Yeşil, Göknur Bayram

    Poly (methyl methacrylate) (PMMA) and PMMA/poly (ethylene glycol) (PEG)-based composite fibers were produced using electrospinning technique with two different additives; halloysite nanotubes (HNTs) and boron phosphate (BPO 4 ). The effect of the additives on the morphology, wettability and dye adsorption properties of electrospun fibers were investigated by Scanning Electron Microscopy (SEM), water contact angle measurement and UV-VIS spectrophotometry. The results of SEM analysis indicated that addition of PEG resulted in thinner average fiber diameter and beaded structure. Additionally, it was also observed that incorporating both HNT and BPO 4 to the PMMA solution caused increased fiber diameter which might be due to increased solution viscosity. For PMMA fibers containing 3 wt% HNT, the highest average diameter and water contact angle were measured as 2204 ± 302 nm and 110.29 ± 3.9°, respectively. The produced fibers were tested for the capability to adsorb methylene blue (MB) and methyl orange (MO) from aqueous solutions. Dye adsorption capacity of the samples increased by addition of HNT and BPO 4 . According to adsorption capacity results, PMMA/PEG/BPO 4 composite sample containing 5 wt% BPO 4 , with an adsorption capacity of 0.76 mg/g, was determined as adsorbent for kinetic and isotherm studies. The adsorption kinetics were well described by the pseudo-second-order model, and equilibrium data were correlated with the Langmuir model.


  • Open Access

    Flame retardancy and mechanical properties of polypropylene composites containing intumescent flame retardants, preceramic polymers, and other additives

    by Sibel Donmez, Zeynep Tuzenli, Goknur Bayram, Sevil Savaskan Yilmaz

    This study aims to investigate the flame retardancy and mechanical properties of polypropylene (PP)‐based intumescent flame retardants (IFRs) consisting of melamine phosphate (MP) and pentaerythritol (PER), and different additives; boron phosphate (BP), antimony oxide (AO), and preceramic polymers, namely poly(dimethylsilane) (PDMS) and poly(methylsilsesquioxane) (PMSQ). The composites were produced by twin‐screw extrusion, and then molded by injection molding. Their characterizations were performed with limiting oxygen index (LOI), horizontal burning tests, thermogravimetric analysis (TGA), tensile and impact tests. The total amount of IFRs and the additives in polypropylene was kept constant at 20 wt%. The additive concentration was varied as 1, 3, and 5 wt% in the composites. The highest LOI value of 29% was obtained for PP/MP/PER composite with MP/PER ratio of 3/1. PP/IFR‐based composites with 1 wt% additive exhibited higher LOI and horizontal burning performance than the other composites with 3 and 5 wt% additives. It is revealed that tensile modulus and impact strength of neat PP were improved with the addition of IFRs, and for each type and amount of the additives used in the study.Highlights: Usage of IFRs, preceramic polymers, BP and AO in PP improved flame retardancy. Lower amount of additives (1%) in PP/IFR composites led to higher LOI values. Additive incorporation enhanced tensile modulus and impact strength of neat PP.


  • Open Access

    Influence of nanocomposite preparation techniques on the multifunctional properties of carbon fabric‐reinforced polystyrene‐based composites with carbon nanotubes

    by Berrak Erkmen, Goknur Bayram

    Polystyrene (PS)‐based and carbon fabric‐reinforced polymers (CFRPs) containing elastomer were prepared using the compression molding technique. PS was also reinforced with two types of carbon nanotubes (CNTs), as received and modified with a silane‐coupling agent. Nanocomposites were fabricated with two different methods, masterbatch dilution, and direct melt mixing. The effect of the nanocomposite preparation technique on the mechanical properties, electrical resistivity, and shape memory behavior of the multilayer composites was investigated. The tensile strength and tensile modulus of the multilayer composite containing CNTs modified with silane coupling agent, and prepared with masterbatch dilution method, increased by 33% and 34%, respectively, compared with the composites prepared with melt mixing. With the masterbatch dilution technique, the electrical resistivity was lower, and slightly increased with surface modification of CNTs. In both preparation techniques, the possible combined effect of CNTs and CF on the thermal and electrical conductivity of the composites led to 100% shape recovery lower than 30 s with electrically actuated bending test.


  • Role of formulation additives on the properties of thermoplastic polyether ester elastomer-based and carbon fabric-reinforced multilayer composites

    by Miray Yasar, Hande Celebi, Goknur Bayram

    In this study, multilayer carbon fabric-reinforced composites (CFRC) were manufactured by compression molding technique with the combination of carbon fabric and thermoplastic polyether ester elastomer (TPEE) composites. The TPEE-based polymer layers were prepared as binary, ternary, and quaternary composites using carbon black (CB) or N-(β-aminoethyl)-γ-aminopropyl-trimethoxysilane (AEAP) modified carbon black (mCB), ethylene-glycidyl methacrylate copolymer (EGMA) and/or paraffin oil. The effects of formulation additives on multilayer CFRC were investigated in terms of their mechanical, electrical resistivity, electrically stimulated shape memory properties and morphologies. Tensile modulus of neat TPEE included multilayer CFRC increased slightly with the addition of both mCB and oil to TPEE. The highest impact strength of 112.2 kJ/m2 was obtained for TPEE-mCB-EGMA-Oil containing CFRC multilayer composites, which was 30% higher than CFRC with neat TPEE. All modified and reinforced CFRC exhibited higher electrical conductivities than neat TPEE containing CFRC. Electrically triggered bending test showed that combination of TPEE, mCB, EGMA and oil together with carbon fabric in multilayer structure revealed 80% shape recovery ratio within less than 2 min.


  • Controlling the foam morphology of supercritical CO2‐processed poly(methyl methacrylate) with CO2‐philic hybrid nanoparticles

    by Merve Ozkutlu, Goknur Bayram, Cerag Dilek

    Highly CO2‐philic nanoparticles, octatrimethylsiloxy polyhedral oligomeric silsesquioxanes (POSS) are used to increase the affinity of poly(methyl methacrylate) (PMMA) to CO2 in supercritical carbon dioxide (scCO2) foaming, thus to improve its foaming performance and the foam morphology. PMMA and PMMA‐POSS composite foams were produced based on the two‐factorial design, at the upper and lower experimental conditions of pressure, temperature, processing time, and venting rate. The foams of PMMA‐5% POSS composites exhibited smaller average pore sizes and higher pore densities than neat PMMA and PMMA‐0.5% POSS composites. The smallest average pore diameter (0.3 μm) and the highest pore density (6.33 × 1012 cm−3) were obtained with this composite processed at 35°C, 32 MPa, for 24 h and depressurized with fast‐venting rate (0.4 MPa/s). ScCO2 processing decreased the density of the polymer by more than 50%.


  • Improvement in mechanical, electrical, and shape memory properties of the polystyrene‐based carbon fiber‐reinforced polymer composites containing carbon nanotubes

    by Berrak Erkmen, Goknur Bayram

    Carbon fiber‐reinforced polymers based on polystyrene matrix containing elastomer and carbon nanotubes (CNTs) were produced by compression molding. The effects of carbon fabric (CF) concentration and silane treatment on the morphology, mechanical, electrical, and shape memory properties of the multilayer composites were investigated. The SEM analyses showed that fibers of the silane‐treated CFs were more homogeneously covered with the polymer layers than the untreated CFs. The tensile strength and modulus of the composites increased by 521% and 125%, respectively, with an increasing number of CF plies from one to five. Upon silane treatment, the tensile strength of the multilayer composite improved by 26%, and the tensile modulus decreased by 18.4%. Electrical conductivities of the composites were in the semiconductor region due to the presence of both CNTs and CFs. 100% shape recovery less than a minute recovery time was obtained for all the composites with electrically triggered bending test.


  • Effects of mixing sequence on epoxy/polyether polyol/organoclay ternary nanocomposites

    by Isil Isik-Gulsac, Ulku Yilmazer, Goknur Bayram

    The effects of mixing sequence of the polyether polyol and curing agent (triethylenetetramine) on mechanical and thermal properties and morphology of epoxy/polyether polyol/organoclay ternary nanocomposites are investigated in this study. The polyether polyol domain size data are relatively unchanged with mixing order both in epoxy/polyether polyol blends and in ternary nanocomposites. Generally, impact strength data of the ternary nanocomposites prepared by the second addition order are higher than the ones produced by the first addition order. Flexural strength and strain at break may be accepted as unaltered generally for the ternary nanocomposites with respect to addition order. Except for the sample containing 3 wt-% Cloisite ® 30B and 3 wt. % polyether polyol, flexural modulus data are close to each other in ternary nanocomposites. The highest flexural modulus is obtained for the 5 wt-% Cloisite ® 30B and 3 wt-% polyether polyol sample prepared by the second addition order, as 2978 ± 27 MPa.


  • Poly(methyl methacrylate) hybrid syntactic foams with hollow glass microspheres and polyhedral oligomeric silsesquioxanes

    by Merve Ozkutlu, Cerag Dilek, Goknur Bayram

    The study aims to produce poly(methyl methacrylate) (PMMA)‐based lower density syntactic foams with hollow glass microspheres (HGMs) and to improve their mechanical properties by the addition of polyhedral oligomeric silsesquioxanes (POSSs) while maintaining the thermal properties of the neat polymer. First to understand the effect of POSS addition, PMMA–POSS composites with octaisobutyl and octaphenyl POSS were produced through extrusion. Higher relative flexural and impact strengths were obtained with POSS addition to PMMA. Obtaining more enhanced properties with octaphenyl POSS, PMMA‐HGM‐POSS hybrid syntactic foams were prepared with this additive. In general, the specific flexural strength and modulus of the PMMA syntactic foams were improved with the POSS loading, while the lower density and thermal properties of the PMMA syntactic foams were maintained. PMMA hybrid syntactic foams with 15 wt % HGMs and 0.25 wt % POSS exhibited 37.6% improvement in the specific flexural modulus with respect to the neat PMMA. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48368.


  • Flame retardancy and mechanical properties of pet‐based composites containing phosphorus and boron‐based additives

    by Mert Kilinc, Gaye O. Cakal, Goknur Bayram, Inci Eroglu, Saim Özkar

    Flame retardancy of poly(ethylene terephthalate), PET, was improved using different flame retardant additives such as triphenylphosphate, triphenylphosphine oxide, zinc borate, and boron phosphate (BP). Composites were prepared using a twin screw extruder and subsequently injection molded for characterization purposes. The flame retardancy of the composites was determined by the limiting oxygen index (LOI) test. Smoke emission during fire was also evaluated in terms of percent light transmittance. Thermal stability and tensile properties of PET‐based composites were compared with PET through TGA and tensile test, respectively. The LOI of the flame retardant composites increased from 21% of neat PET, up to 36% with the addition of 5% BP and 5% triphenyl phosphate to the matrix. Regarding the smoke density analysis, BP was determined as an effective smoke suppressant for PET. Enhanced tensile properties were obtained for the flame retardant PET‐based composites with respect to PET. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42016.