BLBrittany Laing

Brittany Laing

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Brittany Laing has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Adhesion between ethylene‐propylene‐diene monomer and thermoplastics in two‐component injection molding: Effect of dicumylperoxide as curing agent

    by Brittany Laing, Jozefien De Keyzer, David Seveno, Albert Van Bael

    Strong adhesion at the interface is an important aspect in two‐component (2K) injection molding. It was therefore investigated whether dicumylperoxide (DCP) as curing agent in ethylene‐propylene‐diene monomer (EPDM) could stimulate interdiffusion and/or induce chemical bonding with thermoplastics. EPDM mixtures containing DCP concentrations between 2 to 8 parts per hundred rubber (phr) were combined with polar and non‐polar thermoplastics. Changes in EPDM physico‐mechanical bulk properties were analyzed, and the adhesion was evaluated by high temperature contact angle measurements and tensile testing. Results showed that DCP concentration did not influence EPDM‐thermoplastic compatibility. However, EPDM adhesion with polyethylene (PE) did improve when using up to 6 phr DCP (57% adhesion) as crosslinking is promoted. While with polypropylene (PP), adhesion linearly decreased (from 55% to 35% adhesion) with higher DCP concentrations due to prevailing scission reactions. Adhesion through chemical bonding with acrylonitrile‐butadiene‐styrene (ABS) caused better adhesion at 4 phr (43% adhesion) compared to polycarbonate (PC) at 4 phr (13% adhesion) where only limited interdiffusion occurs. Thus, selecting the optimal DCP concentration is highly important to boost adhesion between EPDM and thermoplastics. Furthermore, at these optimal DCP concentrations, physico‐mechanical properties require consideration as these properties were significantly affected.


  • Effect of co‐agents on adhesion between peroxide cured ethylene–propylene–diene monomer and thermoplastics in two‐component injection molding

    by Brittany Laing, Jozefien De Keyzer, David Seveno, Albert Van Bael

    Two‐component (2K) injection‐molded products combining ethylene–propylene–diene monomer (EPDM) with polar or nonpolar thermoplastics require strong interfacial bonding. To optimize the adhesion, co‐agents trimethylolpropane trimethacrylate (TMPT) and triallyl cyanurate (TAC) are compared and concentrations were varied between 0 and 12 parts per hundred rubber (phr). Changes in material compatibility were characterized by contact angle measurements at high temperature, the adhesion was evaluated by tensile testing, and physicomechanical properties of the EPDM bulk were analyzed. Results show that with polypropylene, the adhesion increases to an optimum (3 phr TAC or 6 phr TMPT) independent of the co‐agent type, while for polyethylene only TAC (1.5 phr) effectively boosts adhesion. It is surmised that these optimal concentrations promote crosslinking reactions at the interface. For polycarbonate and acrylonitrile–butadiene–styrene, increasing TAC concentration causes higher adhesion due to improved compatibility. Furthermore, physicomechanical bulk properties change significantly with co‐agent concentrations, making the optimal curing composition application dependent. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48414.


  • Effect of process parameters on the adhesion strength in two‐component injection molding of thermoset rubbers and thermoplastics

    by Gert‐Jan Bex, Wim Six, Brittany Laing, Jozefien De Keyzer, Frederik Desplentere, Albert Van Bael

    Recently, a novel two‐component injection molding process has been developed for combining thermoplastics with thermoset rubbers. This process is of interest for example when thermoplastic parts include seals which are usually produced out of thermoset rubber. The present study evaluates the influence of different process parameters on the bond strength by means of a half factorial experimental design. The considered process parameters are the mold temperature at the interface, the injection temperature, the injection speed, the holding pressure, and the initial roughness of the thermoplastic part at the later interface. The study indicates a large influence of the mold temperature at the interface. Furthermore, the holding pressure only affects the adhesion strength when it is set too low or when the holding time is too short. The other process parameters have no significant effect on the adhesion strength. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46495.