Jean-Baptiste Doucet
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jean-Baptiste Doucet has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Benjamin Reig
Laboratoire d’Analyse et d’Architecture des Systemes-Centre National de la Recherche Scientifique (LAAS-CNRS), 7 Avenue du Colonel Roche, 31400 Toulouse, France
2 shared publications - Thierry Camps
CNRS, LAAS-MICA, 7 Avenue du Colonel Roche, 31400 Toulouse, France
2 shared publications - Veronique Bardinal
Université de Toulouse, LAAS-CNRS, CNRS, Toulouse, France
2 shared publications - Clement Tronche
LAAS-CNRS, Université de Toulouse, CNRS, INP-ENSEEIHT, 31400 Toulouse, France
1 shared publication - Emmanuelle Daran
CNRS, LAAS, Univ de Toulouse, 7 avenue du colonel Roche, F-31400 Toulouse, France
1 shared publication - Fabien Mesnilgrente
LAAS-CNRS, Université de Toulouse, CNRS, INP, UPS, F-31400 Toulouse, France
1 shared publication
Latest Publications
- Open Access
- 13 December 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (24) , 5484
Implementation of Integrated VCSEL-Based Optical Feedback Interferometry Microfluidic Sensor System with Polymer Microoptics
Using the optical feedback interferometry (OFI) technique, we demonstrated a miniaturized and compact sensor system based on a dedicated optical source for flowmetry at the micro-scale. In the system, polymer microlenses were integrated directly on a VCSEL (vertical-cavity surface-emitting laser) chip and the microfluidic channel chip surface using polymer-based micro-fabrication technologies. In particular, at a post-process stage, we integrated a collimation lens on a VCSEL chip of small dimensions (200 µm × 200 µm × 150 µm). This process was enabled by the soft-printing of dry thick resist films and through direct laser writing technology. We performed flow rate measurements using this new compact system, with a conventional bulk glass lens configuration for system performance evaluation. A maximum 33 dB signal-to-noise ratio was achieved from this novel ultra-compact system. To our knowledge, this is the highest signal level achieved by existing OFI based flowmetry sensors.
- 13 December 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (24) , 5484
Open AccessImplementation of Integrated VCSEL-Based Optical Feedback Interferometry Microfluidic Sensor System with Polymer Microoptics
Using the optical feedback interferometry (OFI) technique, we demonstrated a miniaturized and compact sensor system based on a dedicated optical source for flowmetry at the micro-scale. In the system, polymer microlenses were integrated directly on a VCSEL (vertical-cavity surface-emitting laser) chip and the microfluidic channel chip surface using polymer-based micro-fabrication technologies. In particular, at a post-process stage, we integrated a collimation lens on a VCSEL chip of small dimensions (200 µm × 200 µm × 150 µm). This process was enabled by the soft-printing of dry thick resist films and through direct laser writing technology. We performed flow rate measurements using this new compact system, with a conventional bulk glass lens configuration for system performance evaluation. A maximum 33 dB signal-to-noise ratio was achieved from this novel ultra-compact system. To our knowledge, this is the highest signal level achieved by existing OFI based flowmetry sensors.
- 12 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 21 (4) , 41-48
Advances in Polymer-Based Optical MEMS Fabrication for VCSEL Beam Shaping
In this paper, we discuss the design, fabrication, and characterization of electrothermally actuated polymer-based microoptical electromechanical microsystems (MOEMS) for active microoptics in vertical cavity surface emitting laser (VCSEL) devices. We describe in particular the principle of a SU8-based MOEMS designed for single-mode VCSEL beam active focusing. The ultimate objective is the realization of parallel compact optical scanners for sensing applications using collective and low-cost technologies. After discussing the advantages of the epoxy resist SU-8 for fabricating an integrated movable lens on active optical devices, we present our latest advances in technology for ensuring precise MOEMS fabrication on small III-V samples and for achieving accurate alignment of lenses on suspended circular membranes. Finally, we present our first results on the beam focusing of multimode VCSELs, which demonstrate the feasibility of our approach and could provide new insights in the MEMS-VCSEL field.
- 12 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 21 (4) , 41-48
Advances in Polymer-Based Optical MEMS Fabrication for VCSEL Beam Shaping
In this paper, we discuss the design, fabrication, and characterization of electrothermally actuated polymer-based microoptical electromechanical microsystems (MOEMS) for active microoptics in vertical cavity surface emitting laser (VCSEL) devices. We describe in particular the principle of a SU8-based MOEMS designed for single-mode VCSEL beam active focusing. The ultimate objective is the realization of parallel compact optical scanners for sensing applications using collective and low-cost technologies. After discussing the advantages of the epoxy resist SU-8 for fabricating an integrated movable lens on active optical devices, we present our latest advances in technology for ensuring precise MOEMS fabrication on small III-V samples and for achieving accurate alignment of lenses on suspended circular membranes. Finally, we present our first results on the beam focusing of multimode VCSELs, which demonstrate the feasibility of our approach and could provide new insights in the MEMS-VCSEL field.