XQXiaoqing Qiang

Xiaoqing Qiang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Xiaoqing Qiang has a total of 63 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A vertical four-stage low-speed research compressor: Design and experiments

    by Kailong Xia, Hefang Deng, Lin Fan, Hui Liu, Zhenzhou Ju, Mingmin Zhu, Xiaoqing Qiang, Jinfang Teng

    This paper describes a four-stage, vertical, low-speed research compressor (LSRC) at Shanghai Jiao Tong University (SJTU). The compressor has a casing diameter of 1.5 m and was designed following the Wisler similarity methodology to reproduce the aerodynamics of a rear stage of a modern civil high-pressure compressor. The vertical installation provides an axisymmetric baseline for controlled studies of non-axisymmetric tip clearance. The instrumentation combines interstage five-hole probe traverses, L-shaped probes for intra-passage flow surveys, and an 80-port flush-mounted Kulite array above all four rotor stages. Three experimental campaigns with nine test articles are reported, and repeat runs quantify the uncertainty of efficiency differences. In the first campaign, a single-variable test design isolates rotor and stator contributions to stage loss. In the second campaign, reshaping the stationary end wall of the stator hub cavity raises the design-point efficiency by 1.17 points at the same seal clearance, whereas reducing the seal clearance of the baseline cavity nearly threefold produces no resolved change. In the third campaign, a non-axisymmetric inlet guide vane stagger distribution and a second-harmonic tip clearance distribution on the first rotor reduce the design-point efficiency by 0.55 and 0.63 points, with no resolved change in stall margin. Casing pressure measurements show that the clearance pattern modulates the pressure trough beneath the tip leakage vortex at two cycles per revolution, with an amplitude eight times that of the baseline. These measurements establish the SJTU-LSRC as a multistage platform capable of resolving aerodynamic features that are difficult to isolate in high-speed rigs.

  • Design optimization methods for a compressor rotor under inlet distortion

    by Hefang Deng, Songan Zhang, Honglin He, Mingmin Zhu, Xiaoqing Qiang, Jinfang Teng

  • Aerodynamic performance in a boundary layer ingesting fan with swirl distortion

    by Hefang Deng, Huihui Li, Songan Zhang, Mingmin Zhu, Xiaoqing Qiang, Jinfang Teng


  • Improved Reynolds-averaged Navier–Stokes modeling strategies for a compressor linear cascade with an open clearance

    by Gangduo Zhang, Mingmin Zhu, Hui Liu, Xiaoqing Qiang, Jinfang Teng, Jian Li

    To improve aero engine efficiency, the engine core size must be minimized. This reduction increases blade tip clearance, challenging accurate performance predictions for small aspect ratio open clearance cascades using Reynolds-averaged Navier–Stokes (RANS) simulations. While direct numerical simulations and large eddy simulations (LES) are effective, their high computational costs limit practicality in compressor design. Thus, enhancing RANS accuracy under open clearance conditions is critical. The study explores whether different modeling standards are needed for large clearance and identifies criteria for turbulence model modification and mesh configurations. Data-driven modifications to turbulence model have improved tip leakage flow predictions in regular cascades. Altering mesh topology has also enhanced predictions. Both approaches are applied individually and combined in RANS simulations, compared with LES results from a controlled diffusion airfoil cascade. The generalized K-Omega (GEKO) turbulence model is modified using data-driven methods based on LES results. Optimization minimizes differences in total pressure loss and blade surface static pressure coefficients between LES and RANS simulations. Based on optimization via neural networks and the non-dominated Sorting Genetic Algorithm II, the modified GEKO model matches LES results for loss distributions, though improvements in static pressure predictions are limited. Mesh topology modifications, including capped mesh and tangential direction adjustments, are tested individually and in combination. Comparison among four configurations shown superior performance when both modifications are applied. Combining these methods enhances RANS simulation accuracy for loss and static pressure predictions in open clearance cascades. Validation against experimental results confirms the approach's potential for accurate performance predictions.


  • Non-uniform fillet optimum design for a low aspect-ratio compressor cascade under different boundary layer thicknesses

    by Gangduo Zhang, Mingmin Zhu, Songan Zhang, Hui Liu, Xiaoqing Qiang, Jinfang Teng

    To meet the demands for higher thermal efficiency in aero engines, reducing the engine core size is necessary. However, this reduction leads to unscalable geometric features, such as larger blade fillets and more complex inflow conditions, posing challenges for small aspect ratio compressors. Variable fillets have proven effective in controlling corner blockage in compressor cascades under regular boundary layer conditions. This study optimized non-uniform fillet designs for cascades with characteristics of high-pressure compressor rear stages. Two optimization procedures were conducted under two boundary layers, targeting total pressure loss coefficients at design and near-stall conditions. The optimized fillet design achieved up to 5.1% loss reduction at 0° incidence and 30.5% at 6° incidence. The flow mechanism analysis revealed that the optimized non-uniform fillet enhances performance by increasing flow acceleration near the suction peak, reducing blockage, and minimizing local velocity gradients in the corner region. Design criteria for non-uniform fillets were proposed: (1) increasing fillet size from the leading edge to the suction peak and decreasing it toward the trailing edge to enhance acceleration; (2) matching fillet width to blockage size near the end wall to restrain blockage; (3) limiting fillet size near the trailing edge to avoid stronger wakes. To validate these criteria, the non-uniform fillet design was applied to a small aspect ratio Controlled Diffusion Airfoil compressor cascade. The cascade achieved a minimum of 5.1% and a maximum of 15.1% total pressure loss reduction at various incidences. The results confirm the potential of non-uniform fillet design in controlling corner flow.


  • Stall mechanisms of a transonic compressor rotor with axisymmetric and nonaxisymmetric tip clearance layouts

    by Kailong Xia, Huihui Li, Hefang Deng, Huayin Chen, Mingmin Zhu, Xiaoqing Qiang, Jinfang Teng

    This study employs full-annulus unsteady simulations to explore the unsteady tip flow and stall mechanisms in a transonic compressor with axisymmetric (ASY) and nonaxisymmetric (NASY) tip clearance layouts. The investigation highlights the impact of second-harmonic clearance distributions, caused by casing ovalization, on aerodynamic stability and stall behavior. While the stall inception from near stall to stall conditions shows similar characteristics (spike-type inception) for both layouts, the NASY layout results in distinct stall mechanisms. A second-harmonic axial momentum distribution of tip leakage flow is observed before stall onset, aligned with the clearance distribution. After stall onset, this pattern deteriorates, particularly in regions with increasing clearance, where enhanced axial momentum and faster stall cell propagation (approximately 75% of the rotational speed) are observed. In contrast, sectors with decreasing clearance exhibit weaker stall intensity and propagation speed comparable to the ASY layout (62.5% of the rotational speed). These dynamics reduce the stall margin of the transonic compressor with NASY clearances. A circumferential stall cell propagation model is developed, capturing the distinct propagation characteristics in NASY layouts. This study emphasizes the necessity of accounting for nonaxisymmetric clearance effects in modeling and predicting compressor stall behavior and stability.


  • On the Mechanism of Rotating Stall in a Boundary Layer Ingesting Fan

    by Hefang Deng, Songan Zhang, Kai-Long Xia, Xiaoqing Qiang, Mingmin Zhu, Jinfang Teng

    Next-generation boundary layer ingesting (BLI) aircraft can achieve significant reductions in fuel burns compared to conventional aircraft. One of the challenges for BLI aircraft is the need for the fan to continuously operate with inlet distortions. However, until now the effect of real BLI distortions on rotating stall remains unclear. In this work, full-annulus unsteady simulations are conducted to analyze the mechanism of rotating stalls in a boundary layer ingesting fan. The complete stall hysteresis loop at BLI distortions is investigated. Similar to the uniform inflow, the fan at the BLI distortions also exhibits the spike-type rotating stalls, and its stall inception is also attributed to the radial vortex structure caused by the shear interaction between the incoming flow and backflow. However, at the BLI distortions, the evolution process of rotating stall is accompanied by the growth and decay of disturbances because of the significant variation of the inflow condition around the whole annulus. Only when the stall disturbance becomes large enough can it propagate circumferentially across the whole annulus to form the full stall cell. In addition, due to the significant decrease in total pressure ratio, the fan at the BLI distortions is easier to exit the rotating stall compared to the uniform inflow. These results enhance the understanding of the rotating stall mechanism not only for BLI fans but also for many turbine engines that suffer from inlet distortions.