Carmen Catalina Rusu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Carmen Catalina Rusu has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Elena Scutelnicu
Centre for Advanced Research in Welding, Manufacturing Engineering Department, Faculty of Engineering, “Dunarea de Jos” University of Galati, 80008 Galati, Romania
5 shared publications - Arungalai Vendan Subbiah
Electronics and Communication Department, Dayananda Sagar University, Bangalore 560068, India
2 shared publications - Danut Mihailescu
Manufacturing Engineering Department, Faculty of Engineering, “Dunarea de Jos” University of Galati, 800008 Galati, Romania
2 shared publications - George Simion
Faculty of Engineering, “Dunărea de Jos” University of Galati, 800008 Galati, Romania
2 shared publications - L. R. Mistodie
Dunarea de Jos" University of Galati, Faculty of Engineering, Department of Manufacturing Engineering, Romania
2 shared publications - Luigi Renato Mistodie
Manufacturing Engineering Department, Faculty of Engineering, “Dunarea de Jos” University of Galati, 800008 Galati, Romania
2 shared publications
Latest Publications
- 15 December 2025
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 36, 13-24
Comparative Analysis by Finite Element Method of Welding Paths in Aluminium Alloys T-Joints
In recent decades, due to their great advantages, the aluminium alloys have been more and more used in the shipbuilding industry, particularly in the construction of yacht superstructures. Nevertheless, a significant disadvantage of aluminium alloys subjected to welding is their high deformation tendency, which represents an important drawback that needs additional remedial measures. In this study, a finite element analysis was performed, in order to investigate and optimize the design of welding paths used to carry out AA 5083 aluminium alloy T-joints of 6mm thick sheets by Metal Inert Gas (MIG) welding. The research methodology was focused on three case studies, in order to determine and comparatively analyse the Heat Affected Zone extend and the level of stress and displacement. In the first case, the welding beads were successively deposited, following the same welding direction. In the second case, the seams were successively welded, but the welding directions on one side and on the other side of the joint were opposite. In the third case, the seams were simultaneously welded, on both sides of the joint, the welding directions being opposite, as in the previous case study. Based on the research results, it was found that the larger Heat Affected Zone (HAZ) was identified in the third case study, while the total displacement was 25-30% lower, in comparison with the results obtained in the first two case studies. This phenomenon can be explained by the high amount of heat developed simultaneously by two electric arcs and transferred, by conduction, to the base materials. Due to the joining technology applied, that consisted in welding simultaneously on the both sides of the joint, an adequate balance of stress and strain was achieved, determining a lower total displacement.
- 15 December 2025
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 36, 13-24
Comparative Analysis by Finite Element Method of Welding Paths in Aluminium Alloys T-Joints
In recent decades, due to their great advantages, the aluminium alloys have been more and more used in the shipbuilding industry, particularly in the construction of yacht superstructures. Nevertheless, a significant disadvantage of aluminium alloys subjected to welding is their high deformation tendency, which represents an important drawback that needs additional remedial measures. In this study, a finite element analysis was performed, in order to investigate and optimize the design of welding paths used to carry out AA 5083 aluminium alloy T-joints of 6mm thick sheets by Metal Inert Gas (MIG) welding. The research methodology was focused on three case studies, in order to determine and comparatively analyse the Heat Affected Zone extend and the level of stress and displacement. In the first case, the welding beads were successively deposited, following the same welding direction. In the second case, the seams were successively welded, but the welding directions on one side and on the other side of the joint were opposite. In the third case, the seams were simultaneously welded, on both sides of the joint, the welding directions being opposite, as in the previous case study. Based on the research results, it was found that the larger Heat Affected Zone (HAZ) was identified in the third case study, while the total displacement was 25-30% lower, in comparison with the results obtained in the first two case studies. This phenomenon can be explained by the high amount of heat developed simultaneously by two electric arcs and transferred, by conduction, to the base materials. Due to the joining technology applied, that consisted in welding simultaneously on the both sides of the joint, an adequate balance of stress and strain was achieved, determining a lower total displacement.
- Open Access
- 29 September 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (19) , 10530
Optimization of Parameters in Multi-Spot Projection Welding of Thin Aluminized Steel Sheets
Welding is a technological variant of the electric resistance spot-welding process in which the machined protrusion on the surface is heated and rapidly deformed, and the small molten zone formed at the interface is then forged to form the weld spot. The paper analyses the effects of projection welding parameter values for thin, low-carbon aluminized steel sheets. Two sets of 16 welded samples having three or five protrusions were performed and analyzed using the Taguchi method. The microstructural aspects were analyzed in cross sections made through the welded points, highlighting the expulsion or accumulated effects of the Al-Si alloy protective layer and the formation of intermetallic compounds. To estimate the effect of welding parameters, the samples were subjected to tensile strength tests, and the fracture mode was evaluated. It was found that the values of the breaking forces were close for the two types of samples analyzed, for identical values of the welding regime parameters, but the elongation at break was double in the case of samples with five protrusions. The breaking force increased from 10.9 kN for samples with three protrusions to 11.4 kN for samples with five protrusions, for the same values of welding parameters.
- 29 September 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (19) , 10530
Open AccessOptimization of Parameters in Multi-Spot Projection Welding of Thin Aluminized Steel Sheets
Welding is a technological variant of the electric resistance spot-welding process in which the machined protrusion on the surface is heated and rapidly deformed, and the small molten zone formed at the interface is then forged to form the weld spot. The paper analyses the effects of projection welding parameter values for thin, low-carbon aluminized steel sheets. Two sets of 16 welded samples having three or five protrusions were performed and analyzed using the Taguchi method. The microstructural aspects were analyzed in cross sections made through the welded points, highlighting the expulsion or accumulated effects of the Al-Si alloy protective layer and the formation of intermetallic compounds. To estimate the effect of welding parameters, the samples were subjected to tensile strength tests, and the fracture mode was evaluated. It was found that the values of the breaking forces were close for the two types of samples analyzed, for identical values of the welding regime parameters, but the elongation at break was double in the case of samples with five protrusions. The breaking force increased from 10.9 kN for samples with three protrusions to 11.4 kN for samples with five protrusions, for the same values of welding parameters.
- Open Access
Critical Review on Magnetically Impelled Arc Butt Welding: Challenges, Perspectives and Industrial Applications
Magnetically Impelled Arc Butt (MIAB) welding is a cutting-edge joining method that replaces the conventional welding procedures such as resistance, friction, flash and butt welding. It is a solid-state process that uses a rotating arc to heat up the butt ends of tubes, being followed by a forging process that completes the joining of the workpieces The magnetic flux density and the current interact to develop the Lorentz force that impels the arc along the faying surfaces. This process is found to produce high tensile strength and defect-free welds in ferrous materials and for this reason, it is predominantly employed in automobile applications for joining metallic tubes. Also, this joining procedure can be applied in the fabrication of boilers, heat exchangers, furnace piping in petrochemical industry and other safety-critical high-pressure machinery parts. The MIAB method has several advantages such as a shorter welding cycle, lower input energy requirement and lower loss of material. Compared to other solid-state welding processes, the MIAB welding has an important advantage in terms of cost-efficient welds with better control and reliability. Moreover, there are researchers who have investigated the joining of non-ferrous dissimilar materials using this welding procedure. The studies have been focused on process parametric analysis that involves optimizing and forecasting the magnetic field and thermal profile distribution. This review article provides competitive insights into various design features, computational methods, tests and material characterization, technical issues and workarounds, as well as automation aspects related to the MIAB-welding process. This work will prove to be a quick reference for researchers, useful to identify the research gaps and conflicting ideas that can be further explored for advancements in joining the similar and dissimilar materials.
Open AccessCritical Review on Magnetically Impelled Arc Butt Welding: Challenges, Perspectives and Industrial Applications
Magnetically Impelled Arc Butt (MIAB) welding is a cutting-edge joining method that replaces the conventional welding procedures such as resistance, friction, flash and butt welding. It is a solid-state process that uses a rotating arc to heat up the butt ends of tubes, being followed by a forging process that completes the joining of the workpieces The magnetic flux density and the current interact to develop the Lorentz force that impels the arc along the faying surfaces. This process is found to produce high tensile strength and defect-free welds in ferrous materials and for this reason, it is predominantly employed in automobile applications for joining metallic tubes. Also, this joining procedure can be applied in the fabrication of boilers, heat exchangers, furnace piping in petrochemical industry and other safety-critical high-pressure machinery parts. The MIAB method has several advantages such as a shorter welding cycle, lower input energy requirement and lower loss of material. Compared to other solid-state welding processes, the MIAB welding has an important advantage in terms of cost-efficient welds with better control and reliability. Moreover, there are researchers who have investigated the joining of non-ferrous dissimilar materials using this welding procedure. The studies have been focused on process parametric analysis that involves optimizing and forecasting the magnetic field and thermal profile distribution. This review article provides competitive insights into various design features, computational methods, tests and material characterization, technical issues and workarounds, as well as automation aspects related to the MIAB-welding process. This work will prove to be a quick reference for researchers, useful to identify the research gaps and conflicting ideas that can be further explored for advancements in joining the similar and dissimilar materials.
- Top Cited PapersOpen Access
Wire Arc Additive Manufacturing: Review on Recent Findings and Challenges in Industrial Applications and Materials Characterization
Wire arc additive manufacturing (WAAM) is a fusion manufacturing process in which the heat energy of an electric arc is employed for melting the electrodes and depositing material layers for wall formation or for simultaneously cladding two materials in order to form a composite structure. This directed energy deposition-arc (DED-arc) method is advantageous and efficient as it produces large parts with structural integrity due to the high deposition rates, reduced wastage of raw material, and low consumption of energy in comparison with the conventional joining processes and other additive manufacturing technologies. These features have resulted in a constant and continuous increase in interest in this modern manufacturing technique which demands further studies to promote new industrial applications. The high demand for WAAM in aerospace, automobile, nuclear, moulds, and dies industries demonstrates compatibility and reflects comprehensiveness. This paper presents a comprehensive review on the evolution, development, and state of the art of WAAM for non-ferrous materials. Key research observations and inferences from the literature reports regarding the WAAM applications, methods employed, process parameter control, optimization and process limitations, as well as mechanical and metallurgical behavior of materials have been analyzed and synthetically discussed in this paper. Information concerning constraints and enhancements of the wire arc additive manufacturing processes to be considered in terms of wider industrial applicability is also presented in the last part of this paper.
Top Cited PapersOpen AccessWire Arc Additive Manufacturing: Review on Recent Findings and Challenges in Industrial Applications and Materials Characterization
Wire arc additive manufacturing (WAAM) is a fusion manufacturing process in which the heat energy of an electric arc is employed for melting the electrodes and depositing material layers for wall formation or for simultaneously cladding two materials in order to form a composite structure. This directed energy deposition-arc (DED-arc) method is advantageous and efficient as it produces large parts with structural integrity due to the high deposition rates, reduced wastage of raw material, and low consumption of energy in comparison with the conventional joining processes and other additive manufacturing technologies. These features have resulted in a constant and continuous increase in interest in this modern manufacturing technique which demands further studies to promote new industrial applications. The high demand for WAAM in aerospace, automobile, nuclear, moulds, and dies industries demonstrates compatibility and reflects comprehensiveness. This paper presents a comprehensive review on the evolution, development, and state of the art of WAAM for non-ferrous materials. Key research observations and inferences from the literature reports regarding the WAAM applications, methods employed, process parameter control, optimization and process limitations, as well as mechanical and metallurgical behavior of materials have been analyzed and synthetically discussed in this paper. Information concerning constraints and enhancements of the wire arc additive manufacturing processes to be considered in terms of wider industrial applicability is also presented in the last part of this paper.
- Open Access
Metallurgical and Mechanical Characterization of Low Carbon Steel—Stainless Steel Dissimilar Joints Made by Laser Autogenous Welding
This paper addresses the metallurgical and mechanical characterization of dissimilar joints made by laser autogenous welding between thin sheets of low-carbon steel (CS) and austenitic stainless steel (SS). The welding technology applied, previously optimized to produce sound dissimilar joints, is based on the heat source displacement from the weld gap centerline towards CS, in order to reduce the SS overheating. The research includes optical microscopy observations, energy dispersive X-ray analysis (EDX) to assess the wt% of Cr, Ni, and Fe in all regions of the dissimilar welded joint, hardness measurements, and tensile tests of transverse-welded flat specimens. In comparison with classical determination of the joint overall mechanical characteristics, the novelty of this research consists of experimental assessment of the local mechanical behavior of the fusion and heat affected zones by using a digital image correlation technique (VIC-2D). This is an efficient tool for determining the constitutive properties of the joint, useful for modelling the mechanical behavior of materials and for verifying the engineering predictions. The results show that the positive difference in yielding between the weld metal and the base materials protects the joint from being plastically deformed. As a consequence, the tensile loading of flat transverse specimens generates the strain localization and failure in CS, far away from the weld.
Open AccessMetallurgical and Mechanical Characterization of Low Carbon Steel—Stainless Steel Dissimilar Joints Made by Laser Autogenous Welding
This paper addresses the metallurgical and mechanical characterization of dissimilar joints made by laser autogenous welding between thin sheets of low-carbon steel (CS) and austenitic stainless steel (SS). The welding technology applied, previously optimized to produce sound dissimilar joints, is based on the heat source displacement from the weld gap centerline towards CS, in order to reduce the SS overheating. The research includes optical microscopy observations, energy dispersive X-ray analysis (EDX) to assess the wt% of Cr, Ni, and Fe in all regions of the dissimilar welded joint, hardness measurements, and tensile tests of transverse-welded flat specimens. In comparison with classical determination of the joint overall mechanical characteristics, the novelty of this research consists of experimental assessment of the local mechanical behavior of the fusion and heat affected zones by using a digital image correlation technique (VIC-2D). This is an efficient tool for determining the constitutive properties of the joint, useful for modelling the mechanical behavior of materials and for verifying the engineering predictions. The results show that the positive difference in yielding between the weld metal and the base materials protects the joint from being plastically deformed. As a consequence, the tensile loading of flat transverse specimens generates the strain localization and failure in CS, far away from the weld.
- 18 December 2020
- Published by ICI Bucharest in Studies in Informatics and Control
- Vol. 29 (4) , 433-443
An IoT Environmental and Motion Assistance System for the Smart Mobility Context
- 18 December 2020
- Published by ICI Bucharest in Studies in Informatics and Control
- Vol. 29 (4) , 433-443
An IoT Environmental and Motion Assistance System for the Smart Mobility Context
- Open Access
- 18 December 2019
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 30, 34-42
Condition-Based Maintenance Model for the Optimization of Smart Manufacturing Processes
The research focused on the elaboration of the Condition-Based Maintenance (CBM) for the optimization of Smart Manufacturing Processes (SMP) using three types of condition monitoring (CM). The paper presents some considerations regarding the Smart Manufacturing Processes (SMP), especially focused on the Additive Manufacturing (AM) process, by Fused Deposition Modelling (FDM) technology and the way in which the CM and mathematical and probabilistic models can be used, for achieving CBM. The experiments focused on testing three different types of CM: vibration (by vibrometers), sound (by sound level meters) and temperature (by thermal camera and infrared thermography). The experiments and results were analysed, data were processed and a probabilistic model was designed, based on statistical methods, using features/key indicators and their thresholds values. Furthermore, a specific model based on Bayesian network was developed, for achieving CBM of the SMP, specifically to the AM/FDM process. This technique and approach can represent a successful integration of a large number of data monitoring sets and complex modelling and analysis capabilities which can lead in the end to an optimisation of the SMP.
- 18 December 2019
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 30, 34-42
Open AccessCondition-Based Maintenance Model for the Optimization of Smart Manufacturing Processes
The research focused on the elaboration of the Condition-Based Maintenance (CBM) for the optimization of Smart Manufacturing Processes (SMP) using three types of condition monitoring (CM). The paper presents some considerations regarding the Smart Manufacturing Processes (SMP), especially focused on the Additive Manufacturing (AM) process, by Fused Deposition Modelling (FDM) technology and the way in which the CM and mathematical and probabilistic models can be used, for achieving CBM. The experiments focused on testing three different types of CM: vibration (by vibrometers), sound (by sound level meters) and temperature (by thermal camera and infrared thermography). The experiments and results were analysed, data were processed and a probabilistic model was designed, based on statistical methods, using features/key indicators and their thresholds values. Furthermore, a specific model based on Bayesian network was developed, for achieving CBM of the SMP, specifically to the AM/FDM process. This technique and approach can represent a successful integration of a large number of data monitoring sets and complex modelling and analysis capabilities which can lead in the end to an optimisation of the SMP.
- 5 April 2017
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 33 (7) , 718-726
Experimental investigations on the polypropylene behavior during ultrasonic welding
The polypropylene material meets the needs and requirements in automotive industry due to its features such as wide range of physical properties, ease of processing, and low cost. This research has focused on the investigation of the behavior of polypropylene during ultrasonic welding process. The lap welded samples were examined by modern methods such as Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), and Fourier Transform Infrared Spectroscopy (FTIR). Also, the morphology of the non-welded and welded regions of the polypropylene samples was analyzed by Scanning Electronic Microscopy (SEM) method. TGA and DSC results showed a negligible difference between the mass loss of the molded and the welded propylene materials. Furthermore, the SEM images revealed the formation of voids in close correlation with vibration amplitude. The weld strength and bond integrity appears to be higher for higher vibrations, emphasizing that the lap joint interface strength is higher when the tendency of voids formation is decreasing. The stress-strain curve of the material, plotted for three ultrasonic welding variants, illustrated that increasing the main process parameters (pressure, time, and vibration amplitude) makes the weld strength higher, but a decrease in plasticity was noticed in the welded polypropylene samples.
- 5 April 2017
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 33 (7) , 718-726
Experimental investigations on the polypropylene behavior during ultrasonic welding
The polypropylene material meets the needs and requirements in automotive industry due to its features such as wide range of physical properties, ease of processing, and low cost. This research has focused on the investigation of the behavior of polypropylene during ultrasonic welding process. The lap welded samples were examined by modern methods such as Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), and Fourier Transform Infrared Spectroscopy (FTIR). Also, the morphology of the non-welded and welded regions of the polypropylene samples was analyzed by Scanning Electronic Microscopy (SEM) method. TGA and DSC results showed a negligible difference between the mass loss of the molded and the welded propylene materials. Furthermore, the SEM images revealed the formation of voids in close correlation with vibration amplitude. The weld strength and bond integrity appears to be higher for higher vibrations, emphasizing that the lap joint interface strength is higher when the tendency of voids formation is decreasing. The stress-strain curve of the material, plotted for three ultrasonic welding variants, illustrated that increasing the main process parameters (pressure, time, and vibration amplitude) makes the weld strength higher, but a decrease in plasticity was noticed in the welded polypropylene samples.