George Simion
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
George Simion has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Elena Scutelnicu
Centre for Advanced Research in Welding, Manufacturing Engineering Department, Faculty of Engineering, “Dunarea de Jos” University of Galati, 80008 Galati, Romania
6 shared publications - Dan Cătălin Bîrsan
Manufacturing Engineering Department, Faculty of Engineering, “Dunarea de Jos” University of Galati, 47 Domneasca St., 800008 Galati, Romania
3 shared publications - Ionelia Voiculescu
Quality Engineering and Industrial Technology Department, Industrial Engineering and Robotics Faculty, National University of Science and Technology Politehnica Bucharest, 313, Splaiul Independentei, 060042 Bucharest, Romania
3 shared publications - B. Georgescu
“Dunarea de Jos” University of Galati, Faculty of Engineering, 47 Domneasca St., 800008 – Galati, Romania
2 shared publications - Carmen Catalina Rusu
Manufacturing Engineering Department, Faculty of Engineering, “Dunarea de Jos” University of Galati, 800008 Galati, Romania
2 shared publications - Andrei Mitru
INCD Turbomotoare COMOTI, Bv. Iuliu Maniu 220D, Bucharest, Romania
1 shared publication
Latest Publications
- 15 December 2025
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 36, 13-24
Comparative Analysis by Finite Element Method of Welding Paths in Aluminium Alloys T-Joints
In recent decades, due to their great advantages, the aluminium alloys have been more and more used in the shipbuilding industry, particularly in the construction of yacht superstructures. Nevertheless, a significant disadvantage of aluminium alloys subjected to welding is their high deformation tendency, which represents an important drawback that needs additional remedial measures. In this study, a finite element analysis was performed, in order to investigate and optimize the design of welding paths used to carry out AA 5083 aluminium alloy T-joints of 6mm thick sheets by Metal Inert Gas (MIG) welding. The research methodology was focused on three case studies, in order to determine and comparatively analyse the Heat Affected Zone extend and the level of stress and displacement. In the first case, the welding beads were successively deposited, following the same welding direction. In the second case, the seams were successively welded, but the welding directions on one side and on the other side of the joint were opposite. In the third case, the seams were simultaneously welded, on both sides of the joint, the welding directions being opposite, as in the previous case study. Based on the research results, it was found that the larger Heat Affected Zone (HAZ) was identified in the third case study, while the total displacement was 25-30% lower, in comparison with the results obtained in the first two case studies. This phenomenon can be explained by the high amount of heat developed simultaneously by two electric arcs and transferred, by conduction, to the base materials. Due to the joining technology applied, that consisted in welding simultaneously on the both sides of the joint, an adequate balance of stress and strain was achieved, determining a lower total displacement.
- 15 December 2025
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 36, 13-24
Comparative Analysis by Finite Element Method of Welding Paths in Aluminium Alloys T-Joints
In recent decades, due to their great advantages, the aluminium alloys have been more and more used in the shipbuilding industry, particularly in the construction of yacht superstructures. Nevertheless, a significant disadvantage of aluminium alloys subjected to welding is their high deformation tendency, which represents an important drawback that needs additional remedial measures. In this study, a finite element analysis was performed, in order to investigate and optimize the design of welding paths used to carry out AA 5083 aluminium alloy T-joints of 6mm thick sheets by Metal Inert Gas (MIG) welding. The research methodology was focused on three case studies, in order to determine and comparatively analyse the Heat Affected Zone extend and the level of stress and displacement. In the first case, the welding beads were successively deposited, following the same welding direction. In the second case, the seams were successively welded, but the welding directions on one side and on the other side of the joint were opposite. In the third case, the seams were simultaneously welded, on both sides of the joint, the welding directions being opposite, as in the previous case study. Based on the research results, it was found that the larger Heat Affected Zone (HAZ) was identified in the third case study, while the total displacement was 25-30% lower, in comparison with the results obtained in the first two case studies. This phenomenon can be explained by the high amount of heat developed simultaneously by two electric arcs and transferred, by conduction, to the base materials. Due to the joining technology applied, that consisted in welding simultaneously on the both sides of the joint, an adequate balance of stress and strain was achieved, determining a lower total displacement.
- Open Access
- 13 November 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 7136-7146
Corrosion behaviour of medium entropy alloy deposited on low carbon steel substrate by innovative welding method
- 13 November 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 7136-7146
Open AccessCorrosion behaviour of medium entropy alloy deposited on low carbon steel substrate by innovative welding method
- Open Access
- 30 December 2023
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 34, 57-64
A Synthetic Approach to Cold Pressure Welding on Cogged Surfaces
Pressure welding on cogged surfaces represents a new technological variant of the cold welding. The components that are made from a material with higher plasticity (aluminium, lead etc.), having flat surfaces, are pressed on or between the harder material components (copper, brass, carbon/stainless steel, titanium, etc.) that have cogged surfaces. The main particularity of this technique is to achieve an appropriate joint by deforming only the component with higher plasticity. Due to the low degree of deformation needed, reduced pressure forces are applied in comparison with the classical cold pressure welding. The welding in isolated catching nodes is achieved by gripping, while the aluminium is gliding on the flanks of the teeth. The tensile strength of the joint is relatively low reaching up to 10% of the aluminium part, but can be improved by applying a heat treatment. Welded joints were made in various combinations, resulting in bimetallic or multilayered workpieces. Due to the negligible contact resistance, these joints can be appropriately used for applications in the electrotechnical field.
- 30 December 2023
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 34, 57-64
Open AccessA Synthetic Approach to Cold Pressure Welding on Cogged Surfaces
Pressure welding on cogged surfaces represents a new technological variant of the cold welding. The components that are made from a material with higher plasticity (aluminium, lead etc.), having flat surfaces, are pressed on or between the harder material components (copper, brass, carbon/stainless steel, titanium, etc.) that have cogged surfaces. The main particularity of this technique is to achieve an appropriate joint by deforming only the component with higher plasticity. Due to the low degree of deformation needed, reduced pressure forces are applied in comparison with the classical cold pressure welding. The welding in isolated catching nodes is achieved by gripping, while the aluminium is gliding on the flanks of the teeth. The tensile strength of the joint is relatively low reaching up to 10% of the aluminium part, but can be improved by applying a heat treatment. Welded joints were made in various combinations, resulting in bimetallic or multilayered workpieces. Due to the negligible contact resistance, these joints can be appropriately used for applications in the electrotechnical field.
- Open Access
Critical Review on Magnetically Impelled Arc Butt Welding: Challenges, Perspectives and Industrial Applications
Magnetically Impelled Arc Butt (MIAB) welding is a cutting-edge joining method that replaces the conventional welding procedures such as resistance, friction, flash and butt welding. It is a solid-state process that uses a rotating arc to heat up the butt ends of tubes, being followed by a forging process that completes the joining of the workpieces The magnetic flux density and the current interact to develop the Lorentz force that impels the arc along the faying surfaces. This process is found to produce high tensile strength and defect-free welds in ferrous materials and for this reason, it is predominantly employed in automobile applications for joining metallic tubes. Also, this joining procedure can be applied in the fabrication of boilers, heat exchangers, furnace piping in petrochemical industry and other safety-critical high-pressure machinery parts. The MIAB method has several advantages such as a shorter welding cycle, lower input energy requirement and lower loss of material. Compared to other solid-state welding processes, the MIAB welding has an important advantage in terms of cost-efficient welds with better control and reliability. Moreover, there are researchers who have investigated the joining of non-ferrous dissimilar materials using this welding procedure. The studies have been focused on process parametric analysis that involves optimizing and forecasting the magnetic field and thermal profile distribution. This review article provides competitive insights into various design features, computational methods, tests and material characterization, technical issues and workarounds, as well as automation aspects related to the MIAB-welding process. This work will prove to be a quick reference for researchers, useful to identify the research gaps and conflicting ideas that can be further explored for advancements in joining the similar and dissimilar materials.
Open AccessCritical Review on Magnetically Impelled Arc Butt Welding: Challenges, Perspectives and Industrial Applications
Magnetically Impelled Arc Butt (MIAB) welding is a cutting-edge joining method that replaces the conventional welding procedures such as resistance, friction, flash and butt welding. It is a solid-state process that uses a rotating arc to heat up the butt ends of tubes, being followed by a forging process that completes the joining of the workpieces The magnetic flux density and the current interact to develop the Lorentz force that impels the arc along the faying surfaces. This process is found to produce high tensile strength and defect-free welds in ferrous materials and for this reason, it is predominantly employed in automobile applications for joining metallic tubes. Also, this joining procedure can be applied in the fabrication of boilers, heat exchangers, furnace piping in petrochemical industry and other safety-critical high-pressure machinery parts. The MIAB method has several advantages such as a shorter welding cycle, lower input energy requirement and lower loss of material. Compared to other solid-state welding processes, the MIAB welding has an important advantage in terms of cost-efficient welds with better control and reliability. Moreover, there are researchers who have investigated the joining of non-ferrous dissimilar materials using this welding procedure. The studies have been focused on process parametric analysis that involves optimizing and forecasting the magnetic field and thermal profile distribution. This review article provides competitive insights into various design features, computational methods, tests and material characterization, technical issues and workarounds, as well as automation aspects related to the MIAB-welding process. This work will prove to be a quick reference for researchers, useful to identify the research gaps and conflicting ideas that can be further explored for advancements in joining the similar and dissimilar materials.
- 15 December 2022
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 33, 89-94
Numerical Modelling of Thermo-Mechanical Effects Developed in Resistance Spot Welding of E304 Steel with Copper Interlayer
Resistance spot welding is a joining technique of two metal plates, employing pressure and heat. This welding process uses the metals’ electrical resistance to generate the heat that is needed to form the joints from similar or dissimilar metals. In the specialized literature, there are studies for different types of welding processes on the influence of using an interlayer material in both similar and dissimilar joints. In most of the cases, when the parameter optimisation was performed the results lead to an increase in the joint’s strength. In this paper, it is studied the resistance spot welding of 1mm thick E304 stainless steel sheets with and without a copper foil interlayer, using the same welding parameters for both cases. The tensile test of the joints showed a decrease in the resistance of the ones with copper foil interlayer and so, for this combination of materials, optimization of the welding parameters was performed using finite element analysis.
- 15 December 2022
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 33, 89-94
Numerical Modelling of Thermo-Mechanical Effects Developed in Resistance Spot Welding of E304 Steel with Copper Interlayer
Resistance spot welding is a joining technique of two metal plates, employing pressure and heat. This welding process uses the metals’ electrical resistance to generate the heat that is needed to form the joints from similar or dissimilar metals. In the specialized literature, there are studies for different types of welding processes on the influence of using an interlayer material in both similar and dissimilar joints. In most of the cases, when the parameter optimisation was performed the results lead to an increase in the joint’s strength. In this paper, it is studied the resistance spot welding of 1mm thick E304 stainless steel sheets with and without a copper foil interlayer, using the same welding parameters for both cases. The tensile test of the joints showed a decrease in the resistance of the ones with copper foil interlayer and so, for this combination of materials, optimization of the welding parameters was performed using finite element analysis.
- Open Access
Study on the Weldability of Copper—304L Stainless Steel Dissimilar Joint Performed by Robotic Gas Tungsten Arc Welding
The welding process of dissimilar metals, with distinct chemical, physical, thermal, and structural properties, needs to be studied and treated with special attention. The main objectives of this research were to investigate the weldability of the dissimilar joint made between the 99.95% Cu pipe and the 304L stainless steel plate by robotic Gas Tungsten Arc Welding (GTAW), without filler metal and without preheating of materials, and to find the optimum welding regime. Based on repeated adjustments of the main process parameters—welding speed, oscillation frequency, pulse frequency, main welding current, pulse current, and decrease time of welding current at the process end—it was determined the optimum process and, further, it was possible to carry out joints free of cracks and porosity, with full penetration, proper compactness, and sealing properties, that ensure safety in operating conditions. The microstructure analysis revealed the fusion zone as a multi-element alloy with preponderant participation of Cu that has resulted from mixing the non-ferrous elements and iron. Globular Cu- or Fe-rich compounds were developed during welding, being detected by Scanning Electron Microscope (SEM). Moreover, the Energy Dispersive X-ray Analysis (EDAX) recorded the existence of a narrow double mixing zone formed at the interface between the fusion zone and the 304L stainless steel that contains about 66 wt.% Fe, 18 wt.% Cr, 8 wt.% Cu, and 4 wt.% Ni. Due to the formation of Fe-, Cr-, and Ni-rich compounds, a hardness increase up to 127 HV0.2 was noticed in the fusion zone, in comparison with the copper material, where the average measured microhardness was 82 HV0.2. The optimization of the robotic welding regime was carried out sequentially, by adjusting the parameters values, and, further, by analyzing the effects of welding on the geometry and on the appearance of the weld bead. Finally, employing the optimum welding regime—14 cm/min welding speed, 125 A main current, 100 A pulse current, 2.84 Hz oscillation frequency, and 5 Hz pulse frequency—appropriate dissimilar joints, without imperfections, were achieved.
Open AccessStudy on the Weldability of Copper—304L Stainless Steel Dissimilar Joint Performed by Robotic Gas Tungsten Arc Welding
The welding process of dissimilar metals, with distinct chemical, physical, thermal, and structural properties, needs to be studied and treated with special attention. The main objectives of this research were to investigate the weldability of the dissimilar joint made between the 99.95% Cu pipe and the 304L stainless steel plate by robotic Gas Tungsten Arc Welding (GTAW), without filler metal and without preheating of materials, and to find the optimum welding regime. Based on repeated adjustments of the main process parameters—welding speed, oscillation frequency, pulse frequency, main welding current, pulse current, and decrease time of welding current at the process end—it was determined the optimum process and, further, it was possible to carry out joints free of cracks and porosity, with full penetration, proper compactness, and sealing properties, that ensure safety in operating conditions. The microstructure analysis revealed the fusion zone as a multi-element alloy with preponderant participation of Cu that has resulted from mixing the non-ferrous elements and iron. Globular Cu- or Fe-rich compounds were developed during welding, being detected by Scanning Electron Microscope (SEM). Moreover, the Energy Dispersive X-ray Analysis (EDAX) recorded the existence of a narrow double mixing zone formed at the interface between the fusion zone and the 304L stainless steel that contains about 66 wt.% Fe, 18 wt.% Cr, 8 wt.% Cu, and 4 wt.% Ni. Due to the formation of Fe-, Cr-, and Ni-rich compounds, a hardness increase up to 127 HV0.2 was noticed in the fusion zone, in comparison with the copper material, where the average measured microhardness was 82 HV0.2. The optimization of the robotic welding regime was carried out sequentially, by adjusting the parameters values, and, further, by analyzing the effects of welding on the geometry and on the appearance of the weld bead. Finally, employing the optimum welding regime—14 cm/min welding speed, 125 A main current, 100 A pulse current, 2.84 Hz oscillation frequency, and 5 Hz pulse frequency—appropriate dissimilar joints, without imperfections, were achieved.
- Open Access
Effect of Diffusion on Dissimilar Welded Joint between Al0.8CoCrFeNi High-Entropy Alloy and S235JR Structural Steel
This research focused on the investigation of the metallurgical behavior of the Al0.8CoCrFeNi high-entropy alloy and S235JR structural steel, welded with (Ni, Fe)-rich filler metal, by the Gas Tungsten Arc Welding (GTAW) method. The electric arc and the welding pool were protected against the contamination with gases from the environment, by employing high-purity Ar 4.8 inert gas that plays an important role in reducing the oxidation effects and the development of cracks in the weld and the adjacent areas. The microstructure and microhardness analysis did not reveal the existence of fragile phases, cracks, inadequate penetration, or other imperfections, showing an appropriate adhesion between the deposited metal and the substrates. At the interface between the Ni-rich weld metal and the high-entropy alloy, a higher hardness (448 HV0.2) than in the base material (358 HV0.2) was measured. Energy-dispersive X-ray analysis (EDS), performed at the interface between the weld metal and the base materials, did not show significant modifications of Co, Fe, and Cr percentages. However, during the investigation, significant variations in Al and Ni concentrations were observed, caused by the fast diffusion of chemical elements, and the development of hard (Ni, Al)-rich compounds. In some areas of the deposited metal, located at a distance of about 10 µm from the interface, the percentages of Ni and Al were higher than in the high-entropy alloy base material, being around 41% by weight Ni and over 13% by weight Al, while the concentrations of the Co, Cr, and Fe elements proportionally decreased (i.e., approximately 14% by weight Co, 12% by weight Cr, and 17% by weight Fe). The development of Ni3Al and NiAl compounds was also noticed, whose formation was determined by the local chemical concentration and the temperature reached in the vicinity of the diffusion zone. The XRD analysis showed a group of X-ray peaks in the Al0.8CrFeCoNi alloy that corresponded to both α-type—BCC and FCC phases. The crystallite size of the high-entropy alloy investigated was found to be 22.05 nm. Despite the diffusion phenomenon, if filler materials and process parameters are appropriately selected, quality joints of high-entropy alloys and structural steels can be carried out under good welding conditions.
Open AccessEffect of Diffusion on Dissimilar Welded Joint between Al0.8CoCrFeNi High-Entropy Alloy and S235JR Structural Steel
This research focused on the investigation of the metallurgical behavior of the Al0.8CoCrFeNi high-entropy alloy and S235JR structural steel, welded with (Ni, Fe)-rich filler metal, by the Gas Tungsten Arc Welding (GTAW) method. The electric arc and the welding pool were protected against the contamination with gases from the environment, by employing high-purity Ar 4.8 inert gas that plays an important role in reducing the oxidation effects and the development of cracks in the weld and the adjacent areas. The microstructure and microhardness analysis did not reveal the existence of fragile phases, cracks, inadequate penetration, or other imperfections, showing an appropriate adhesion between the deposited metal and the substrates. At the interface between the Ni-rich weld metal and the high-entropy alloy, a higher hardness (448 HV0.2) than in the base material (358 HV0.2) was measured. Energy-dispersive X-ray analysis (EDS), performed at the interface between the weld metal and the base materials, did not show significant modifications of Co, Fe, and Cr percentages. However, during the investigation, significant variations in Al and Ni concentrations were observed, caused by the fast diffusion of chemical elements, and the development of hard (Ni, Al)-rich compounds. In some areas of the deposited metal, located at a distance of about 10 µm from the interface, the percentages of Ni and Al were higher than in the high-entropy alloy base material, being around 41% by weight Ni and over 13% by weight Al, while the concentrations of the Co, Cr, and Fe elements proportionally decreased (i.e., approximately 14% by weight Co, 12% by weight Cr, and 17% by weight Fe). The development of Ni3Al and NiAl compounds was also noticed, whose formation was determined by the local chemical concentration and the temperature reached in the vicinity of the diffusion zone. The XRD analysis showed a group of X-ray peaks in the Al0.8CrFeCoNi alloy that corresponded to both α-type—BCC and FCC phases. The crystallite size of the high-entropy alloy investigated was found to be 22.05 nm. Despite the diffusion phenomenon, if filler materials and process parameters are appropriately selected, quality joints of high-entropy alloys and structural steels can be carried out under good welding conditions.
- Open Access
- 31 December 2021
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 32, 37-46
Numerical Model Developed for Thermo-Mecahnical Analysis in AlCrFeMnNiHf0.05–Armox 500 Steel Welded Joint
High entropy alloys are a new category of materials that contain at least four main chemical elements. One of the main advantages over the traditional alloys is the ability to maintain their properties at low or high temperatures. Researchers have investigated the possibility of welding these alloys so that they can be used in industrial applications. Good results have been obtained by welding butt joints of thin sheets, without the use of filler materials. In this paper it is investigated the possibility of welding overlap joints, with applications in the military field, of medium-thickness plates of AlCrFeMnNiHf0.05high entropy alloy on an Armox 500 steel support plate, using filler materials available on the market. The research focuses on the numerical simulation of three welding processes commonly used in on-site repair operations, namely manual metal arc, metal inert gas, and tungsten inert gas.
- 31 December 2021
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 32, 37-46
Open AccessNumerical Model Developed for Thermo-Mecahnical Analysis in AlCrFeMnNiHf0.05–Armox 500 Steel Welded Joint
High entropy alloys are a new category of materials that contain at least four main chemical elements. One of the main advantages over the traditional alloys is the ability to maintain their properties at low or high temperatures. Researchers have investigated the possibility of welding these alloys so that they can be used in industrial applications. Good results have been obtained by welding butt joints of thin sheets, without the use of filler materials. In this paper it is investigated the possibility of welding overlap joints, with applications in the military field, of medium-thickness plates of AlCrFeMnNiHf0.05high entropy alloy on an Armox 500 steel support plate, using filler materials available on the market. The research focuses on the numerical simulation of three welding processes commonly used in on-site repair operations, namely manual metal arc, metal inert gas, and tungsten inert gas.