Elena Scutelnicu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Elena Scutelnicu has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Mihaela Iordachescu
Material Science Department, ETSI Caminos, Polytechnic University of Madrid, 5 Prof. Aranguren St., 28040 Madrid, Spain
11 shared publications - George Simion
Faculty of Engineering, “Dunărea de Jos” University of Galati, 800008 Galati, Romania
6 shared publications - Carmen Catalina Rusu
Manufacturing Engineering Department, Faculty of Engineering, “Dunarea de Jos” University of Galati, 800008 Galati, Romania
5 shared publications - Andrés Valiente
Material Science Department, ETSI Caminos, Polytechnic University of Madrid, 5 Prof. Aranguren St., 28040 Madrid, Spain
4 shared publications - Jose Luis Ocana
Universidad Politécnica de Madrid
4 shared publications - Patricia Santos
Applied Physics and Materials Engineering Department, ETSI Industriales, Polytechnic University of Madrid, 2 José Gutiérrez Abascal St., 28006 Madrid, Spain
4 shared publications
Latest Publications
- Open Access
- 2 March 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (3) , 89
New Insight into Mechanical, Microstructural and Failure Features of Lap-Fillet Autogenous Laser-Welded Similar and Dissimilar Joints of Ultra-Thin Steel Sheets
This research work addresses the mechanical and metallurgical characterisation, as well as the failure features, of two types of lap-fillet autogenous laser-welded joints made of ultra-thin sheets by applying an appropriate welding technology for producing sound welds and flawless joints. Both welded samples, one made only of stainless steel (SS-SS) sheets, and the other made of stainless steel and carbon steel (SS-CS) plates, were subjected to tensile–shear loads that are representative of the in-service conditions. The experimental research was focused on determining, by the digital image correlation (VIC-2D) method, the strain field and the rotation angle of the welded joints that were developed during loading tests of the welded specimens. Comparing to the classical testing method applied to study the joint overall mechanical properties, the novelty of this research consists of local mechanical behaviour assessment of relevant zones from similar and dissimilar welded joints, by using the innovative technique VIC-2D. Based on the analysis of the experimental results, it was found that the maximum rotation angle is 2.5 times higher in the SS-SS similar welded joint, in comparison with the SS-CS dissimilar welded joint. Despite this finding, the SS-CS specimen failed in the CS base material, far from the weld, with the failure phenomenon being preceded by the material yielding and necking. This failure mode is consistent with the detected strength mismatch of the SS-CS joint, with respect to the CS base material. In contrast, the quasi-ductile fracture of the SS-SS welded joint occurred by plastic exhaustion at the boundary between the narrow Heat-Affected Zone (HAZ) of SS and the Fuzion Zone (FZ). These outcomes are consistent with the hardness profile, microstructural heterogeneities found in the lap-fillet welded joints, and the load versus elongation curves that are determined and discussed in this paper. This research provides new insight and original information on the materials’ response to the autogenous laser welding, which will contribute to improving the knowledge on the ultra-thin lap-fillet welded similar and dissimilar steels.
- 2 March 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (3) , 89
Open AccessNew Insight into Mechanical, Microstructural and Failure Features of Lap-Fillet Autogenous Laser-Welded Similar and Dissimilar Joints of Ultra-Thin Steel Sheets
This research work addresses the mechanical and metallurgical characterisation, as well as the failure features, of two types of lap-fillet autogenous laser-welded joints made of ultra-thin sheets by applying an appropriate welding technology for producing sound welds and flawless joints. Both welded samples, one made only of stainless steel (SS-SS) sheets, and the other made of stainless steel and carbon steel (SS-CS) plates, were subjected to tensile–shear loads that are representative of the in-service conditions. The experimental research was focused on determining, by the digital image correlation (VIC-2D) method, the strain field and the rotation angle of the welded joints that were developed during loading tests of the welded specimens. Comparing to the classical testing method applied to study the joint overall mechanical properties, the novelty of this research consists of local mechanical behaviour assessment of relevant zones from similar and dissimilar welded joints, by using the innovative technique VIC-2D. Based on the analysis of the experimental results, it was found that the maximum rotation angle is 2.5 times higher in the SS-SS similar welded joint, in comparison with the SS-CS dissimilar welded joint. Despite this finding, the SS-CS specimen failed in the CS base material, far from the weld, with the failure phenomenon being preceded by the material yielding and necking. This failure mode is consistent with the detected strength mismatch of the SS-CS joint, with respect to the CS base material. In contrast, the quasi-ductile fracture of the SS-SS welded joint occurred by plastic exhaustion at the boundary between the narrow Heat-Affected Zone (HAZ) of SS and the Fuzion Zone (FZ). These outcomes are consistent with the hardness profile, microstructural heterogeneities found in the lap-fillet welded joints, and the load versus elongation curves that are determined and discussed in this paper. This research provides new insight and original information on the materials’ response to the autogenous laser welding, which will contribute to improving the knowledge on the ultra-thin lap-fillet welded similar and dissimilar steels.
- 15 December 2025
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 36, 13-24
Comparative Analysis by Finite Element Method of Welding Paths in Aluminium Alloys T-Joints
In recent decades, due to their great advantages, the aluminium alloys have been more and more used in the shipbuilding industry, particularly in the construction of yacht superstructures. Nevertheless, a significant disadvantage of aluminium alloys subjected to welding is their high deformation tendency, which represents an important drawback that needs additional remedial measures. In this study, a finite element analysis was performed, in order to investigate and optimize the design of welding paths used to carry out AA 5083 aluminium alloy T-joints of 6mm thick sheets by Metal Inert Gas (MIG) welding. The research methodology was focused on three case studies, in order to determine and comparatively analyse the Heat Affected Zone extend and the level of stress and displacement. In the first case, the welding beads were successively deposited, following the same welding direction. In the second case, the seams were successively welded, but the welding directions on one side and on the other side of the joint were opposite. In the third case, the seams were simultaneously welded, on both sides of the joint, the welding directions being opposite, as in the previous case study. Based on the research results, it was found that the larger Heat Affected Zone (HAZ) was identified in the third case study, while the total displacement was 25-30% lower, in comparison with the results obtained in the first two case studies. This phenomenon can be explained by the high amount of heat developed simultaneously by two electric arcs and transferred, by conduction, to the base materials. Due to the joining technology applied, that consisted in welding simultaneously on the both sides of the joint, an adequate balance of stress and strain was achieved, determining a lower total displacement.
- 15 December 2025
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 36, 13-24
Comparative Analysis by Finite Element Method of Welding Paths in Aluminium Alloys T-Joints
In recent decades, due to their great advantages, the aluminium alloys have been more and more used in the shipbuilding industry, particularly in the construction of yacht superstructures. Nevertheless, a significant disadvantage of aluminium alloys subjected to welding is their high deformation tendency, which represents an important drawback that needs additional remedial measures. In this study, a finite element analysis was performed, in order to investigate and optimize the design of welding paths used to carry out AA 5083 aluminium alloy T-joints of 6mm thick sheets by Metal Inert Gas (MIG) welding. The research methodology was focused on three case studies, in order to determine and comparatively analyse the Heat Affected Zone extend and the level of stress and displacement. In the first case, the welding beads were successively deposited, following the same welding direction. In the second case, the seams were successively welded, but the welding directions on one side and on the other side of the joint were opposite. In the third case, the seams were simultaneously welded, on both sides of the joint, the welding directions being opposite, as in the previous case study. Based on the research results, it was found that the larger Heat Affected Zone (HAZ) was identified in the third case study, while the total displacement was 25-30% lower, in comparison with the results obtained in the first two case studies. This phenomenon can be explained by the high amount of heat developed simultaneously by two electric arcs and transferred, by conduction, to the base materials. Due to the joining technology applied, that consisted in welding simultaneously on the both sides of the joint, an adequate balance of stress and strain was achieved, determining a lower total displacement.
- 15 December 2025
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 36, 55-66
Evaluation of Microstructure, Mechanical and Tribological Properties of AA6061 Reinforced with SiC and CuO Particles by Friction Stir Processing
Friction Stir Processing (FSP) is a great solid-state surface modification method that can be employed to enhance the mechanical and tribological properties of metallic materials by using reinforcement particles. In the present study, AA6061 aluminium alloy plates with 6mm thickness were subjected to FSP process with constant parameters of 1000 rpm rotational speed and 50 mm/min traverse speed, by employing a cylindrical taper pin tool. Silicon carbide (SiC) and copper oxide (CuO) particles were incorporated in various quantities (1 to 4 wt %) to achieve surface metal matrix composites and to evaluate the impact of the reinforcement on the AA6061 alloy mechanical and wear properties. The microstructure investigation, made by optical microscopy method, demonstrated a significant change in grain structure and a uniform distribution of particles in the stir zone. Among four composites samples, the specimen reinforced with 1 wt % SiC and 3 wt % CuO (sample 3) exhibited excellent properties such as tensile strength of 190.7 MPa, elongation of 8.2%, hardness of 72.9 HV, and wear rate of 0.0526 mm³/Nm. The fracture surface analysis, performed by Scanning Electron Microscopy (SEM) technique, revealed reduced number of dimples and absence of visible cracks, as well as improved resistance to fracture and adequate structural integrity. Furthermore, the analysis of the worn surface indicated shallow grooves and minimal debris, confirming diminished abrasive wear. The results achieved by the methods presented above make the optimized FSP-treated AA6061 composite a promising material for industrial applications such as automotive components, aerospace structures, and tooling elements.
- 15 December 2025
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 36, 55-66
Evaluation of Microstructure, Mechanical and Tribological Properties of AA6061 Reinforced with SiC and CuO Particles by Friction Stir Processing
Friction Stir Processing (FSP) is a great solid-state surface modification method that can be employed to enhance the mechanical and tribological properties of metallic materials by using reinforcement particles. In the present study, AA6061 aluminium alloy plates with 6mm thickness were subjected to FSP process with constant parameters of 1000 rpm rotational speed and 50 mm/min traverse speed, by employing a cylindrical taper pin tool. Silicon carbide (SiC) and copper oxide (CuO) particles were incorporated in various quantities (1 to 4 wt %) to achieve surface metal matrix composites and to evaluate the impact of the reinforcement on the AA6061 alloy mechanical and wear properties. The microstructure investigation, made by optical microscopy method, demonstrated a significant change in grain structure and a uniform distribution of particles in the stir zone. Among four composites samples, the specimen reinforced with 1 wt % SiC and 3 wt % CuO (sample 3) exhibited excellent properties such as tensile strength of 190.7 MPa, elongation of 8.2%, hardness of 72.9 HV, and wear rate of 0.0526 mm³/Nm. The fracture surface analysis, performed by Scanning Electron Microscopy (SEM) technique, revealed reduced number of dimples and absence of visible cracks, as well as improved resistance to fracture and adequate structural integrity. Furthermore, the analysis of the worn surface indicated shallow grooves and minimal debris, confirming diminished abrasive wear. The results achieved by the methods presented above make the optimized FSP-treated AA6061 composite a promising material for industrial applications such as automotive components, aerospace structures, and tooling elements.
- Open Access
- 27 October 2025
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 9 (11) , 351
On Combined Tensile-Shear Performance of Laser-Welded Dissimilar Overlap Joints Made of Austenitic Stainless Steel and Low-Carbon Steel
This paper addresses the mechanical characterization of dissimilar overlap joints made by autogenous laser welding between thin sheets of low-carbon steel (CS) and austenitic stainless steel (SS) with an optimized welding technology able to produce sound overlap joints. This involved applying the laser beam from the CS-side to reduce the SS overheating. The research is focused on the analysis of combined tensile-shear behavior of the weld and of the heat-affected zones. During testing, the applied tensile-shear load rotates the weld connecting the CS and SS plates. The rotation angle transmitted to the free ends of the plates, together with relevant strain fields, were measured by using a digital image correlation system, VIC-2D. Thus, it was found that the weld acts as a non-linear hinge which experiences a sudden loss of stiffness when strain concentrations develop from the weld ligament edges towards the loaded sides of the plates. The welded joint fails by yielding localization and necking in the CS plate, far from the weld. This mode of failure is a consequence of the weld and heat-affected zone strength mismatches of 1.09 and 1.33, respectively. These values are consistent with the hardness profile and the documented microstructural heterogeneities.
- 27 October 2025
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 9 (11) , 351
Open AccessOn Combined Tensile-Shear Performance of Laser-Welded Dissimilar Overlap Joints Made of Austenitic Stainless Steel and Low-Carbon Steel
This paper addresses the mechanical characterization of dissimilar overlap joints made by autogenous laser welding between thin sheets of low-carbon steel (CS) and austenitic stainless steel (SS) with an optimized welding technology able to produce sound overlap joints. This involved applying the laser beam from the CS-side to reduce the SS overheating. The research is focused on the analysis of combined tensile-shear behavior of the weld and of the heat-affected zones. During testing, the applied tensile-shear load rotates the weld connecting the CS and SS plates. The rotation angle transmitted to the free ends of the plates, together with relevant strain fields, were measured by using a digital image correlation system, VIC-2D. Thus, it was found that the weld acts as a non-linear hinge which experiences a sudden loss of stiffness when strain concentrations develop from the weld ligament edges towards the loaded sides of the plates. The welded joint fails by yielding localization and necking in the CS plate, far from the weld. This mode of failure is a consequence of the weld and heat-affected zone strength mismatches of 1.09 and 1.33, respectively. These values are consistent with the hardness profile and the documented microstructural heterogeneities.
- Open Access
- 11 December 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (24) , 11543
Fatigue, Fracture, and Damage Tolerance of Ultrahigh-Strength Martensitic Tendon-Rods for Structural Engineering
The paper addresses the fatigue resistance, fracture behavior, and damage tolerance of a new type of ultrahigh-strength bar for prestressing concrete made of a low-alloy lath martensitic steel. The fracture tests show that the bar steel has a medium-high fracture toughness of 75 MPa m1/2 and a fatigue cracking resistance that fits the Paris-Erdogan Law as most of Eurocode 3 structural steels. The damage tolerance analysis combines two failure assessment diagrams (FADs), the first focused on the damage level and the second on toughness and yielding capacity as material properties of the bar steel, whose influence and interaction are determinant for failure. The location of the experimental failure data in the FADs indicates that the steel is endowed with a combination of strength, ductility, and toughness able to prevent unexpected failures. The damage micro-mechanisms revealed from the examination of broken specimens differ from fatigue to fracture cracking, but in a manner consistent with the observed mechanical behavior and microstructure of the bar steel.
- 11 December 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (24) , 11543
Open AccessFatigue, Fracture, and Damage Tolerance of Ultrahigh-Strength Martensitic Tendon-Rods for Structural Engineering
The paper addresses the fatigue resistance, fracture behavior, and damage tolerance of a new type of ultrahigh-strength bar for prestressing concrete made of a low-alloy lath martensitic steel. The fracture tests show that the bar steel has a medium-high fracture toughness of 75 MPa m1/2 and a fatigue cracking resistance that fits the Paris-Erdogan Law as most of Eurocode 3 structural steels. The damage tolerance analysis combines two failure assessment diagrams (FADs), the first focused on the damage level and the second on toughness and yielding capacity as material properties of the bar steel, whose influence and interaction are determinant for failure. The location of the experimental failure data in the FADs indicates that the steel is endowed with a combination of strength, ductility, and toughness able to prevent unexpected failures. The damage micro-mechanisms revealed from the examination of broken specimens differ from fatigue to fracture cracking, but in a manner consistent with the observed mechanical behavior and microstructure of the bar steel.
- Open Access
- 20 November 2024
- Published by MDPI AG in Preprints.org
Fatigue, Fracture and Damage Tolerance of Ultrahigh-Strength Martensitic Tendon-Rods for Structural Engineering
The paper addresses the fatigue resistance, fracture behavior and damage tolerance of a new type of ultrahigh-strength bar for prestressing concrete made of a low-alloy lath martensitic steel. The fracture tests showed that the bar steel has a medium-high fracture toughness of 75 MPa√m and a fatigue cracking resistance that fits the Paris-Erdogan Law as most of Eurocode 3 structural steels. The damage tolerance analysis combines two Failure Assessment Diagrams – FADs, respectively involving the damage level and the toughness, and yielding capacity influences on the failure of the bar steel. The location of the experimental failure data in the FADs indicate that the steel is endowed with a combination of strength, ductility and toughness able to prevent unexpected failures. The damage micro-mechanisms revealed from the examination of broken specimens differ from fatigue to fracture cracking, but in a manner consistent with the observed mechanical behavior and microstructure of the bar steel.
- 20 November 2024
- Published by MDPI AG in Preprints.org
Open AccessFatigue, Fracture and Damage Tolerance of Ultrahigh-Strength Martensitic Tendon-Rods for Structural Engineering
The paper addresses the fatigue resistance, fracture behavior and damage tolerance of a new type of ultrahigh-strength bar for prestressing concrete made of a low-alloy lath martensitic steel. The fracture tests showed that the bar steel has a medium-high fracture toughness of 75 MPa√m and a fatigue cracking resistance that fits the Paris-Erdogan Law as most of Eurocode 3 structural steels. The damage tolerance analysis combines two Failure Assessment Diagrams – FADs, respectively involving the damage level and the toughness, and yielding capacity influences on the failure of the bar steel. The location of the experimental failure data in the FADs indicate that the steel is endowed with a combination of strength, ductility and toughness able to prevent unexpected failures. The damage micro-mechanisms revealed from the examination of broken specimens differ from fatigue to fracture cracking, but in a manner consistent with the observed mechanical behavior and microstructure of the bar steel.
- Open Access
- 13 November 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 7136-7146
Corrosion behaviour of medium entropy alloy deposited on low carbon steel substrate by innovative welding method
- 13 November 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 7136-7146
Open AccessCorrosion behaviour of medium entropy alloy deposited on low carbon steel substrate by innovative welding method
- Open Access
- 24 July 2024
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 30 (Supplement)
The Influence of the Re-Melting on the Microstructure and Corrosion Resistance of New Welding Material
High-entropy alloys (HEA) have gained significant attention in the materials sector due to a new and innovative approach to alloy design. This concept was introduced by Yeh et al. and Cantor et al. [ 1, 2]. HEAs, in contrast to metallic materials, typically contain five or more multi-principal elements, with each constituent element having a concentration ranging from 5 to 35 atomic percent.
- 24 July 2024
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 30 (Supplement)
Open AccessThe Influence of the Re-Melting on the Microstructure and Corrosion Resistance of New Welding Material
High-entropy alloys (HEA) have gained significant attention in the materials sector due to a new and innovative approach to alloy design. This concept was introduced by Yeh et al. and Cantor et al. [ 1, 2]. HEAs, in contrast to metallic materials, typically contain five or more multi-principal elements, with each constituent element having a concentration ranging from 5 to 35 atomic percent.
- Open Access
Critical Review on Magnetically Impelled Arc Butt Welding: Challenges, Perspectives and Industrial Applications
Magnetically Impelled Arc Butt (MIAB) welding is a cutting-edge joining method that replaces the conventional welding procedures such as resistance, friction, flash and butt welding. It is a solid-state process that uses a rotating arc to heat up the butt ends of tubes, being followed by a forging process that completes the joining of the workpieces The magnetic flux density and the current interact to develop the Lorentz force that impels the arc along the faying surfaces. This process is found to produce high tensile strength and defect-free welds in ferrous materials and for this reason, it is predominantly employed in automobile applications for joining metallic tubes. Also, this joining procedure can be applied in the fabrication of boilers, heat exchangers, furnace piping in petrochemical industry and other safety-critical high-pressure machinery parts. The MIAB method has several advantages such as a shorter welding cycle, lower input energy requirement and lower loss of material. Compared to other solid-state welding processes, the MIAB welding has an important advantage in terms of cost-efficient welds with better control and reliability. Moreover, there are researchers who have investigated the joining of non-ferrous dissimilar materials using this welding procedure. The studies have been focused on process parametric analysis that involves optimizing and forecasting the magnetic field and thermal profile distribution. This review article provides competitive insights into various design features, computational methods, tests and material characterization, technical issues and workarounds, as well as automation aspects related to the MIAB-welding process. This work will prove to be a quick reference for researchers, useful to identify the research gaps and conflicting ideas that can be further explored for advancements in joining the similar and dissimilar materials.
Open AccessCritical Review on Magnetically Impelled Arc Butt Welding: Challenges, Perspectives and Industrial Applications
Magnetically Impelled Arc Butt (MIAB) welding is a cutting-edge joining method that replaces the conventional welding procedures such as resistance, friction, flash and butt welding. It is a solid-state process that uses a rotating arc to heat up the butt ends of tubes, being followed by a forging process that completes the joining of the workpieces The magnetic flux density and the current interact to develop the Lorentz force that impels the arc along the faying surfaces. This process is found to produce high tensile strength and defect-free welds in ferrous materials and for this reason, it is predominantly employed in automobile applications for joining metallic tubes. Also, this joining procedure can be applied in the fabrication of boilers, heat exchangers, furnace piping in petrochemical industry and other safety-critical high-pressure machinery parts. The MIAB method has several advantages such as a shorter welding cycle, lower input energy requirement and lower loss of material. Compared to other solid-state welding processes, the MIAB welding has an important advantage in terms of cost-efficient welds with better control and reliability. Moreover, there are researchers who have investigated the joining of non-ferrous dissimilar materials using this welding procedure. The studies have been focused on process parametric analysis that involves optimizing and forecasting the magnetic field and thermal profile distribution. This review article provides competitive insights into various design features, computational methods, tests and material characterization, technical issues and workarounds, as well as automation aspects related to the MIAB-welding process. This work will prove to be a quick reference for researchers, useful to identify the research gaps and conflicting ideas that can be further explored for advancements in joining the similar and dissimilar materials.
- Open Access
Study on the Weldability of Copper—304L Stainless Steel Dissimilar Joint Performed by Robotic Gas Tungsten Arc Welding
The welding process of dissimilar metals, with distinct chemical, physical, thermal, and structural properties, needs to be studied and treated with special attention. The main objectives of this research were to investigate the weldability of the dissimilar joint made between the 99.95% Cu pipe and the 304L stainless steel plate by robotic Gas Tungsten Arc Welding (GTAW), without filler metal and without preheating of materials, and to find the optimum welding regime. Based on repeated adjustments of the main process parameters—welding speed, oscillation frequency, pulse frequency, main welding current, pulse current, and decrease time of welding current at the process end—it was determined the optimum process and, further, it was possible to carry out joints free of cracks and porosity, with full penetration, proper compactness, and sealing properties, that ensure safety in operating conditions. The microstructure analysis revealed the fusion zone as a multi-element alloy with preponderant participation of Cu that has resulted from mixing the non-ferrous elements and iron. Globular Cu- or Fe-rich compounds were developed during welding, being detected by Scanning Electron Microscope (SEM). Moreover, the Energy Dispersive X-ray Analysis (EDAX) recorded the existence of a narrow double mixing zone formed at the interface between the fusion zone and the 304L stainless steel that contains about 66 wt.% Fe, 18 wt.% Cr, 8 wt.% Cu, and 4 wt.% Ni. Due to the formation of Fe-, Cr-, and Ni-rich compounds, a hardness increase up to 127 HV0.2 was noticed in the fusion zone, in comparison with the copper material, where the average measured microhardness was 82 HV0.2. The optimization of the robotic welding regime was carried out sequentially, by adjusting the parameters values, and, further, by analyzing the effects of welding on the geometry and on the appearance of the weld bead. Finally, employing the optimum welding regime—14 cm/min welding speed, 125 A main current, 100 A pulse current, 2.84 Hz oscillation frequency, and 5 Hz pulse frequency—appropriate dissimilar joints, without imperfections, were achieved.
Open AccessStudy on the Weldability of Copper—304L Stainless Steel Dissimilar Joint Performed by Robotic Gas Tungsten Arc Welding
The welding process of dissimilar metals, with distinct chemical, physical, thermal, and structural properties, needs to be studied and treated with special attention. The main objectives of this research were to investigate the weldability of the dissimilar joint made between the 99.95% Cu pipe and the 304L stainless steel plate by robotic Gas Tungsten Arc Welding (GTAW), without filler metal and without preheating of materials, and to find the optimum welding regime. Based on repeated adjustments of the main process parameters—welding speed, oscillation frequency, pulse frequency, main welding current, pulse current, and decrease time of welding current at the process end—it was determined the optimum process and, further, it was possible to carry out joints free of cracks and porosity, with full penetration, proper compactness, and sealing properties, that ensure safety in operating conditions. The microstructure analysis revealed the fusion zone as a multi-element alloy with preponderant participation of Cu that has resulted from mixing the non-ferrous elements and iron. Globular Cu- or Fe-rich compounds were developed during welding, being detected by Scanning Electron Microscope (SEM). Moreover, the Energy Dispersive X-ray Analysis (EDAX) recorded the existence of a narrow double mixing zone formed at the interface between the fusion zone and the 304L stainless steel that contains about 66 wt.% Fe, 18 wt.% Cr, 8 wt.% Cu, and 4 wt.% Ni. Due to the formation of Fe-, Cr-, and Ni-rich compounds, a hardness increase up to 127 HV0.2 was noticed in the fusion zone, in comparison with the copper material, where the average measured microhardness was 82 HV0.2. The optimization of the robotic welding regime was carried out sequentially, by adjusting the parameters values, and, further, by analyzing the effects of welding on the geometry and on the appearance of the weld bead. Finally, employing the optimum welding regime—14 cm/min welding speed, 125 A main current, 100 A pulse current, 2.84 Hz oscillation frequency, and 5 Hz pulse frequency—appropriate dissimilar joints, without imperfections, were achieved.