Hamsavathi Kannan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hamsavathi Kannan has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Madappa V. R. Sivasubramanian
Department of Civil Engineering, National Institute of Technology Puducherry, Karaikal 609609, India
3 shared publications - Helen Negash Shiferaw
Graduate School of Science and Technology, University of Tsukuba, Tsukuba 305-8573, Japan
1 shared publication - Shamsher Bahadur Singh
Department of Civil Engineering, Birla Institute of Technology and Science, Pilani, India
1 shared publication Shoya Furukawa
1 shared publication- Toshiyuki Kanakubo
Department of Engineering Mechanics and Energy, University of Tsukuba, Tsukuba 305-8573, Japan
1 shared publication - Veerappan Sathish Kumar
Department of Civil Engineering, National Institute of Technology Puducherry, Karaikal 609609, India
1 shared publication
Latest Publications
- Open Access
- 5 November 2026
- Published by Bentham Science Publishers Ltd. in The Open Construction & Building Technology Journal
- Vol. 20 (1)
Bending Performance and Evaluation of Tensile Properties of Polyester Fiber Reinforced Ductile Fiber Reinforced Cementitious Composite (PES-DFRCC)
Introduction/Objective: This study investigates the flexural and equivalent tensile behaviour of polyester fiber-reinforced ductile fiber-reinforced cementitious composite (PES-DFRCC) incorporating commercially available Indian-manufactured polyester fibers. The influence of fiber volume fraction on the flexural response and equivalent tensile properties was evaluated through four-point bending tests and inverse section analysis. This study presents the first experimental investigation of PES-DFRCC using this methodology and establishes its equivalent tensile stress–strain behaviour. Methods: Beam specimens containing different polyester fiber volume fractions were tested under four-point bending in accordance with ISO 21914:2019. Load, axial deformation, and deflection measurements were recorded, and tensile properties were determined through inverse section analysis based on the observed flexural response. Results: The PES-DFRCC specimens exhibited multiple microcracking and pronounced deflection-hardening behavior under bending. The evaluated average tensile strength ranged from 0.34 to 2.41 MPa, while the corresponding average ultimate tensile strain varied from 0.276% to 0.450%, depending on the fiber content. Discussion: The formation of multiple microcracks contributed to enhanced ductility and energy absorption capacity, indicating the effectiveness of polyester fibers in improving the post-cracking performance of cementitious composites. Conclusion: The newly developed PES-DFRCC demonstrated significant ductile behavior, characterized by multiple cracking, deflection hardening, and improved tensile performance. These findings highlight the potential of polyester fiber reinforcement for developing durable and ductile cementitious materials for structural applications.
- 5 November 2026
- Published by Bentham Science Publishers Ltd. in The Open Construction & Building Technology Journal
- Vol. 20 (1)
Open AccessBending Performance and Evaluation of Tensile Properties of Polyester Fiber Reinforced Ductile Fiber Reinforced Cementitious Composite (PES-DFRCC)
Introduction/Objective: This study investigates the flexural and equivalent tensile behaviour of polyester fiber-reinforced ductile fiber-reinforced cementitious composite (PES-DFRCC) incorporating commercially available Indian-manufactured polyester fibers. The influence of fiber volume fraction on the flexural response and equivalent tensile properties was evaluated through four-point bending tests and inverse section analysis. This study presents the first experimental investigation of PES-DFRCC using this methodology and establishes its equivalent tensile stress–strain behaviour. Methods: Beam specimens containing different polyester fiber volume fractions were tested under four-point bending in accordance with ISO 21914:2019. Load, axial deformation, and deflection measurements were recorded, and tensile properties were determined through inverse section analysis based on the observed flexural response. Results: The PES-DFRCC specimens exhibited multiple microcracking and pronounced deflection-hardening behavior under bending. The evaluated average tensile strength ranged from 0.34 to 2.41 MPa, while the corresponding average ultimate tensile strain varied from 0.276% to 0.450%, depending on the fiber content. Discussion: The formation of multiple microcracks contributed to enhanced ductility and energy absorption capacity, indicating the effectiveness of polyester fibers in improving the post-cracking performance of cementitious composites. Conclusion: The newly developed PES-DFRCC demonstrated significant ductile behavior, characterized by multiple cracking, deflection hardening, and improved tensile performance. These findings highlight the potential of polyester fiber reinforcement for developing durable and ductile cementitious materials for structural applications.
- 3 August 2025
- Published by Springer Nature
- p. 645-652
Numerical Analysis of Steel Reinforced ECC Coupling Beam
- 3 August 2025
- Published by Springer Nature
- p. 645-652
Numerical Analysis of Steel Reinforced ECC Coupling Beam
- Open Access
- 31 July 2025
- Published by MDPI AG in Construction Materials
- Vol. 5 (3) , 51
Experimental and Numerical Investigation of Shear Performance of RC Deep Beams Strengthened with Engineered Cementitious Composites
Reinforced concrete (RC) deep beams constructed with low-strength concrete are susceptible to sudden splitting failures in the strut region due to shear–compression stresses. To mitigate this vulnerability, various strengthening techniques, including steel plates, fiber-reinforced polymer sheets, and cementitious composites, have been explored to confine the strut area. This study investigates the structural performance of RC deep beams with low-strength concrete, strengthened externally using an Engineered Cementitious Composite (ECC) layer. To ensure effective confinement and uniform shear distribution, shear reinforcement was provided at equal intervals with configurations of zero, one, and two vertical shear reinforcements. Four-point bending tests revealed that the ECC layer significantly enhanced the shear capacity, increasing load-carrying capacity by 51.6%, 54.7%, and 46.7% for beams with zero, one, and two shear reinforcements, respectively. Failure analysis through non-linear finite element modeling corroborated experimental observations, confirming shear–compression failure characterized by damage in the concrete struts. The strut-and-tie method, modified to incorporate the tensile strength of ECC and shear reinforcement actual stress values taken from the FE analysis, was used to predict the shear capacity. The predicted values were within 10% of the experimental results, underscoring the reliability of the analytical approach. Overall, this study demonstrates the effectiveness of ECC in improving shear performance and mitigating strut failure in RC deep beams made with low-strength concrete.
- 31 July 2025
- Published by MDPI AG in Construction Materials
- Vol. 5 (3) , 51
Open AccessExperimental and Numerical Investigation of Shear Performance of RC Deep Beams Strengthened with Engineered Cementitious Composites
Reinforced concrete (RC) deep beams constructed with low-strength concrete are susceptible to sudden splitting failures in the strut region due to shear–compression stresses. To mitigate this vulnerability, various strengthening techniques, including steel plates, fiber-reinforced polymer sheets, and cementitious composites, have been explored to confine the strut area. This study investigates the structural performance of RC deep beams with low-strength concrete, strengthened externally using an Engineered Cementitious Composite (ECC) layer. To ensure effective confinement and uniform shear distribution, shear reinforcement was provided at equal intervals with configurations of zero, one, and two vertical shear reinforcements. Four-point bending tests revealed that the ECC layer significantly enhanced the shear capacity, increasing load-carrying capacity by 51.6%, 54.7%, and 46.7% for beams with zero, one, and two shear reinforcements, respectively. Failure analysis through non-linear finite element modeling corroborated experimental observations, confirming shear–compression failure characterized by damage in the concrete struts. The strut-and-tie method, modified to incorporate the tensile strength of ECC and shear reinforcement actual stress values taken from the FE analysis, was used to predict the shear capacity. The predicted values were within 10% of the experimental results, underscoring the reliability of the analytical approach. Overall, this study demonstrates the effectiveness of ECC in improving shear performance and mitigating strut failure in RC deep beams made with low-strength concrete.