Alexandre Torre
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alexandre Torre has a total of 161 co-authors. Here are the top co-authors by number of shared publications:
- Benoit Lacroix
CEA-IRFM, St-Paul Lez Durance, France
20 shared publications - Louis Zani
Fusion for Energy, Garching, Germany
20 shared publications - Quentin Le Coz
CEA-IRFM, St-Paul Lez Durance, France
18 shared publications - Sylvie Nicollet
CEAIRFM, Cadarache, Saint-Paul-lez-Durance, France
12 shared publications - Alexandre Louzguiti
ITER Organization, Saint-Paul-lez-Durance, France
10 shared publications - Daniel Ciazynski
IRFM, CEA, Saint-Paul-lez-Durance France 13108
10 shared publications
Latest Publications
- 20 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 4203505
The SupraFusion French Program: Development of HTS Technologies for Fusion and Wide Societal Applications
The French government has recently launched the SupraFusion Research Program lead by CEA (Commissariat à l'Energie Atomique) and CNRS (Centre National de Recherche Scientifique) with the partnership of multiple other universities. This national program has been granted 50 M€ in order to boost the development of High Temperature Superconductors (HTS) technology towards large societal applications, using the vector of nuclear fusion as a powerful driver for this research and innovation. In order to achieve this goal, the Progam has been built around five technological bricks covering the whole life cycle of the technology. The first brick aims to the characterization and modelling of REBCO tapes increasing confidence in magnet designs and qualification. The second one targets the development of high current & high field conductors matching the main constraints and performances needed by the magnets. The third brick will study HTS coils quench protection and propose new technological solutions to ensure magnets safety. The fourth aims to design, manufacture and test in nominal conditions a large-scale demonstrator achieving about 20 T and 100 MJ of stored energy to prove this technology viability for fusion and other large-scale applications. The fifth brick will propose designs for future HTS compact fusion plants towards energy production. Finally, in order to enable the spread of HTS technology in the society, this large national program will also launch an open call to support technological bricks as well as studies targeting the use of HTS technology in other societal applications that could be MRI, wind generators, motors, high energy physics, etc. This paper will present the French SupraFusion scientific program challenges and objectives.
- 20 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 4203505
The SupraFusion French Program: Development of HTS Technologies for Fusion and Wide Societal Applications
The French government has recently launched the SupraFusion Research Program lead by CEA (Commissariat à l'Energie Atomique) and CNRS (Centre National de Recherche Scientifique) with the partnership of multiple other universities. This national program has been granted 50 M€ in order to boost the development of High Temperature Superconductors (HTS) technology towards large societal applications, using the vector of nuclear fusion as a powerful driver for this research and innovation. In order to achieve this goal, the Progam has been built around five technological bricks covering the whole life cycle of the technology. The first brick aims to the characterization and modelling of REBCO tapes increasing confidence in magnet designs and qualification. The second one targets the development of high current & high field conductors matching the main constraints and performances needed by the magnets. The third brick will study HTS coils quench protection and propose new technological solutions to ensure magnets safety. The fourth aims to design, manufacture and test in nominal conditions a large-scale demonstrator achieving about 20 T and 100 MJ of stored energy to prove this technology viability for fusion and other large-scale applications. The fifth brick will propose designs for future HTS compact fusion plants towards energy production. Finally, in order to enable the spread of HTS technology in the society, this large national program will also launch an open call to support technological bricks as well as studies targeting the use of HTS technology in other societal applications that could be MRI, wind generators, motors, high energy physics, etc. This paper will present the French SupraFusion scientific program challenges and objectives.
- 25 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-6
Magnet Design Activities at CEA for EU-DEMO LAR Baseline 2024
In 2024, a new EU-DEMO baseline (called LAR for Low Aspect Ratio) was released which substantially changed the constraints on the magnets systems, with a key driver for changes the magnet systems being mechanical considerations. This paper will briefly list changes in the new baseline, and give an overview of updates to the CEA design toolbox MADMACS, particularly the implementation of fatigue analysis for the pulsed central solenoid (CS), and consideration of hybrid low/high-temperature superconducting CS coils. The new fatigue tool is later used to perform sensitivity analysis on the assumed parameters for Walker exponent and residual stress, with results showing that further study of these parameters should be of high priority. Summaries of new preliminary toroidal field (TF) coil and CS designs, based on ITER-like approaches, are also given. The final TF design required modifications to the winding pack dimensions, and the CS could only meet all the requirements using HTS inner turns, new jacket materials, and relaxations in fatigue assumptions. Therefore, it is clear that the LAR baseline has not yet resolved the static and fatigue concerns for the magnet systems, when considering ITER-like TF and CS solutions, but that this may be possible with further development.
- 25 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-6
Magnet Design Activities at CEA for EU-DEMO LAR Baseline 2024
In 2024, a new EU-DEMO baseline (called LAR for Low Aspect Ratio) was released which substantially changed the constraints on the magnets systems, with a key driver for changes the magnet systems being mechanical considerations. This paper will briefly list changes in the new baseline, and give an overview of updates to the CEA design toolbox MADMACS, particularly the implementation of fatigue analysis for the pulsed central solenoid (CS), and consideration of hybrid low/high-temperature superconducting CS coils. The new fatigue tool is later used to perform sensitivity analysis on the assumed parameters for Walker exponent and residual stress, with results showing that further study of these parameters should be of high priority. Summaries of new preliminary toroidal field (TF) coil and CS designs, based on ITER-like approaches, are also given. The final TF design required modifications to the winding pack dimensions, and the CS could only meet all the requirements using HTS inner turns, new jacket materials, and relaxations in fatigue assumptions. Therefore, it is clear that the LAR baseline has not yet resolved the static and fatigue concerns for the magnet systems, when considering ITER-like TF and CS solutions, but that this may be possible with further development.
- 21 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Update on CIRCE Mechanical Toolbox for Fusion Magnet System Analysis
Future fusion devices rely on the use of high-field magnetic systems built with high-temperature superconductors (HTS). The interaction between intense magnetic fields and large operating currents induces significant mechanical stresses, which limit the deployment of HTS in fusion magnets. Efficient and reliable analysis tools are therefore essential to evaluate mechanical integrity during the early stages of design. CIRCE (Cast3M Investigation and Research for Coils mechanical Evaluation) is a mechanical toolbox developed to provide fast and parametric assessments of coil systems. It combines simplified electromagnetic and mechanical formulations within a fully parametric framework, enabling magnet designers to identify critical stress regions and determine optimal coil shapes for a given plasma configuration. This paper presents recent updates to CIRCE. A new regularized Biot–Savart formulation enables Lorentz force computation for arbitrary coil geometries. The mechanical beam model has been enhanced and extended to support non-planar coils. Additionally, a local 2D axisymmetric model has been implemented to evaluate transverse stresses at the conductor level. These improvements have been applied to the DEMO-LAR Tokamak and HELIAS 5-B baselines.
- 21 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Update on CIRCE Mechanical Toolbox for Fusion Magnet System Analysis
Future fusion devices rely on the use of high-field magnetic systems built with high-temperature superconductors (HTS). The interaction between intense magnetic fields and large operating currents induces significant mechanical stresses, which limit the deployment of HTS in fusion magnets. Efficient and reliable analysis tools are therefore essential to evaluate mechanical integrity during the early stages of design. CIRCE (Cast3M Investigation and Research for Coils mechanical Evaluation) is a mechanical toolbox developed to provide fast and parametric assessments of coil systems. It combines simplified electromagnetic and mechanical formulations within a fully parametric framework, enabling magnet designers to identify critical stress regions and determine optimal coil shapes for a given plasma configuration. This paper presents recent updates to CIRCE. A new regularized Biot–Savart formulation enables Lorentz force computation for arbitrary coil geometries. The mechanical beam model has been enhanced and extended to support non-planar coils. Additionally, a local 2D axisymmetric model has been implemented to evaluate transverse stresses at the conductor level. These improvements have been applied to the DEMO-LAR Tokamak and HELIAS 5-B baselines.
- 6 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Optimizing Cooling Strategies for CORC Conductors in High-Field Fusion Applications
This work presents a comparative thermal–hydraulic analysis of a CORC (Conductor On Round Core) cable under two classes of external perturbation, fast (20 ms) and slow (1 s), with the goal of evaluating its stability against quench. Four configurations are modeled, each differing in helium flow topology: adiabatic, 1-channel, 2-channel, and 3-channel. The simulations include the effect of thermal contact resistance and friction factor uncertainty in the tape bundle. Results show that under fast perturbations, helium's contribution to stability is limited unless it is in direct contact with the superconducting tapes, while for slow perturbations, helium cooling plays a dominant stabilizing role. Since stability must be achieved across the temperature range from ∼ 4.5 K to 20 K, helium emerges as a key actor in any cooling strategy designed for these conditions. The addition of a relief channel in the 3-channel configuration effectively reduces pressure buildup during fast transients with minimal stability penalty and further enhances performance under slow perturbations.
- 6 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Optimizing Cooling Strategies for CORC Conductors in High-Field Fusion Applications
This work presents a comparative thermal–hydraulic analysis of a CORC (Conductor On Round Core) cable under two classes of external perturbation, fast (20 ms) and slow (1 s), with the goal of evaluating its stability against quench. Four configurations are modeled, each differing in helium flow topology: adiabatic, 1-channel, 2-channel, and 3-channel. The simulations include the effect of thermal contact resistance and friction factor uncertainty in the tape bundle. Results show that under fast perturbations, helium's contribution to stability is limited unless it is in direct contact with the superconducting tapes, while for slow perturbations, helium cooling plays a dominant stabilizing role. Since stability must be achieved across the temperature range from ∼ 4.5 K to 20 K, helium emerges as a key actor in any cooling strategy designed for these conditions. The addition of a relief channel in the 3-channel configuration effectively reduces pressure buildup during fast transients with minimal stability penalty and further enhances performance under slow perturbations.
- 22 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-6
Study of CORC Conductors With Respect to Individual Tape Properties
CEA has been studying the advantages of a conductor based on an assembly of CORC cables in the high field zone of a hybrid Central Solenoid (CS) magnet for EU-DEMO. To this end, the detailed study of geometrical and electrical parameters of a CORC structure are studied in order to evaluate the cable’s electrical performance as well as to determine a number of important parameters (crossing points, contact surface etc…) as function of the cable structure. The paper first presents these geometrical and performance analyses. It will then try to introduce smeared models in order to reduce the cable’s performance to 1D tape scaling law using effective parameters. That reduction is of importance for use in thermohydraulic models. Finally, the paper will present the case study of a particular CORC conductor that is being procured and is foreseen to be tested in SULTAN in 2025. The paper will try to give some predictive estimate of the cable performance and identify some of the unknowns related to current redistribution and joint resistance.
- 22 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-6
Study of CORC Conductors With Respect to Individual Tape Properties
CEA has been studying the advantages of a conductor based on an assembly of CORC cables in the high field zone of a hybrid Central Solenoid (CS) magnet for EU-DEMO. To this end, the detailed study of geometrical and electrical parameters of a CORC structure are studied in order to evaluate the cable’s electrical performance as well as to determine a number of important parameters (crossing points, contact surface etc…) as function of the cable structure. The paper first presents these geometrical and performance analyses. It will then try to introduce smeared models in order to reduce the cable’s performance to 1D tape scaling law using effective parameters. That reduction is of importance for use in thermohydraulic models. Finally, the paper will present the case study of a particular CORC conductor that is being procured and is foreseen to be tested in SULTAN in 2025. The paper will try to give some predictive estimate of the cable performance and identify some of the unknowns related to current redistribution and joint resistance.
- 11 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-6
The CIRCE Code: Cast3M Investigation and Research for Coils Mechanical Evaluation
The recent success of demonstration coils using HTS confirms the promising application of these materials for toroidal field (TF) coils in high-field fusion machines. Potential magnetic fields at around 20 T on the conductor claim to achieve the required performance for commercial reactors with fusion power scaling as ${{P}_f} \propto B_t^4$ under several assumptions. However, this usually involves increased engineering challenges to withstand much higher mechanical loads scaling quadratically with the magnetic field. This paper presents a new mechanical toolbox, named CIRCE: a highly configurable code featuring plane stress analysis and 3D beam analysis, with a case study of tokamak TF coils under in-plane and out-of-plane loads.
- 11 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-6
The CIRCE Code: Cast3M Investigation and Research for Coils Mechanical Evaluation
The recent success of demonstration coils using HTS confirms the promising application of these materials for toroidal field (TF) coils in high-field fusion machines. Potential magnetic fields at around 20 T on the conductor claim to achieve the required performance for commercial reactors with fusion power scaling as ${{P}_f} \propto B_t^4$ under several assumptions. However, this usually involves increased engineering challenges to withstand much higher mechanical loads scaling quadratically with the magnetic field. This paper presents a new mechanical toolbox, named CIRCE: a highly configurable code featuring plane stress analysis and 3D beam analysis, with a case study of tokamak TF coils under in-plane and out-of-plane loads.
- 17 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
On the Evaluation of Current Sharing Temperature Within Conductors of ITER Toroidal Field Coils in Operation
The nineteen ITER Toroidal Field (TF) coils (including a spare one) consists of seven double pancakes (DP) of cable-in-conduit conductors (CICC), each containing 900 superconducting Nb3Sn strands. In total eight strand manufacturing companies were involved, either relying on the bronze route or internal tin process. As a result, the strand, and thus conductor, performance can vary significantly within the same TF coil. This peculiarity inherent to the ITER project makes the evaluation process of coils stability, linked to the current sharing temperature (Tcs), more delicate. Following an extensive conductor testing campaign carried out over several years within the SULTAN facility, degradation of the different TF conductors was observed along electromagnetic and thermal cycling. Relying on the ITER critical current scaling law and associated parameters for TF strands, effective strain properties and n-values were extracted from the SULTAN Tcs measurements. In parallel, recent simulations conducted with MULTIFIL (mechanical code) on TF CICC have shed some light on the strands mechanical state after cool-down and along electro-magnetic cycling, highlighting the importance of the bending strain. Capitalizing on these results, on the SULTAN database, and on the literature (already mentioning the bending strain effect on conductor degradation), we aim at refining the existing methodology of performance scale-up from strands to conductors by introducing the bending strain. Ultimately, we apply the model in an attempt to conciliate SULTAN Tcs measurements and MULTIFIL mechanical results.
- 17 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
On the Evaluation of Current Sharing Temperature Within Conductors of ITER Toroidal Field Coils in Operation
The nineteen ITER Toroidal Field (TF) coils (including a spare one) consists of seven double pancakes (DP) of cable-in-conduit conductors (CICC), each containing 900 superconducting Nb3Sn strands. In total eight strand manufacturing companies were involved, either relying on the bronze route or internal tin process. As a result, the strand, and thus conductor, performance can vary significantly within the same TF coil. This peculiarity inherent to the ITER project makes the evaluation process of coils stability, linked to the current sharing temperature (Tcs), more delicate. Following an extensive conductor testing campaign carried out over several years within the SULTAN facility, degradation of the different TF conductors was observed along electromagnetic and thermal cycling. Relying on the ITER critical current scaling law and associated parameters for TF strands, effective strain properties and n-values were extracted from the SULTAN Tcs measurements. In parallel, recent simulations conducted with MULTIFIL (mechanical code) on TF CICC have shed some light on the strands mechanical state after cool-down and along electro-magnetic cycling, highlighting the importance of the bending strain. Capitalizing on these results, on the SULTAN database, and on the literature (already mentioning the bending strain effect on conductor degradation), we aim at refining the existing methodology of performance scale-up from strands to conductors by introducing the bending strain. Ultimately, we apply the model in an attempt to conciliate SULTAN Tcs measurements and MULTIFIL mechanical results.
- 20 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Design and Qualification of LTS Conductors at CEA for EU-DEMO Toroidal Field Magnet
The EU-DEMO baseline follows the path towards a large-scale tokamak demonstrator. The unmatched size stands as one of the biggest challenge to overcome. Toroidal field magnets are no exception and the expanding performance and limits require the development of new conductor designs. In this regard, CEA design team has been working on the scaling-up of ITER-like conductor technology, with the design, manufacture and test of a square-in-square 100 kA-class conductor called DEMOTF-WP3. It has now been tested in SULTAN and this article presents preliminary results. The sample is composed by two legs containing the same 3.5 m long CICC for redundancy purpose. Voltage taps and temperature sensors are installed along both legs following a symmetrical scheme. This sample also contains a twinbox joint prototype connecting the two legs together at the bottom of the sample thanks to a thin layer of compacted indium. Furthermore, the need expressed at EU-DEMO Gate 1 review to investigate round-in-round geometry permitting the use of radial plates, triggered the CEA design team to propose another Nb3Sn conductor design (DEMOTF-WP4), with operating current of 116 kA and peak field of 12.5 T. This conductor is composed of 721 SC strands and 1108 copper strands cabled together within a round stainless steel jacket with a diameter of 55 mm. The detailed design is presented along with the prototype manufactured that will be used for the qualification tests to be held at SULTAN facility at CRPP in 2025.
- 20 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Design and Qualification of LTS Conductors at CEA for EU-DEMO Toroidal Field Magnet
The EU-DEMO baseline follows the path towards a large-scale tokamak demonstrator. The unmatched size stands as one of the biggest challenge to overcome. Toroidal field magnets are no exception and the expanding performance and limits require the development of new conductor designs. In this regard, CEA design team has been working on the scaling-up of ITER-like conductor technology, with the design, manufacture and test of a square-in-square 100 kA-class conductor called DEMOTF-WP3. It has now been tested in SULTAN and this article presents preliminary results. The sample is composed by two legs containing the same 3.5 m long CICC for redundancy purpose. Voltage taps and temperature sensors are installed along both legs following a symmetrical scheme. This sample also contains a twinbox joint prototype connecting the two legs together at the bottom of the sample thanks to a thin layer of compacted indium. Furthermore, the need expressed at EU-DEMO Gate 1 review to investigate round-in-round geometry permitting the use of radial plates, triggered the CEA design team to propose another Nb3Sn conductor design (DEMOTF-WP4), with operating current of 116 kA and peak field of 12.5 T. This conductor is composed of 721 SC strands and 1108 copper strands cabled together within a round stainless steel jacket with a diameter of 55 mm. The detailed design is presented along with the prototype manufactured that will be used for the qualification tests to be held at SULTAN facility at CRPP in 2025.
- 12 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Upgrade of CICC Mechanical Model and Case Study of ITER TF Conductor in Cold Test Conditions
This paper proposes to use an upgraded version of the Multifil simulation tool to model an ITER TF-like conductor in two cases: In tokamak and in cold test conditions. After briefly introducing the Multifil code, the paper will report the latest upgrades in terms of thermal equilibrium as well as simultaneous Lorentz and coil operational loads. We will present a new post-processing of the fractured filamentary area, which relies on a memory of the fracture map along all the loading steps. Then, considering ITER is currently building a magnet coil test bench (MCTB) with the capability to cold test some of the TF coils at nominal current (68 kA) in a standalone situation, we will discuss how mechanical modelling of the TF conductor is relevant for assessing the impact of the test sequence on the Nb3Sn conductor degradation. We will present a new loading sequence, representative of the test facility conditions, with a different Lorentz force direction and amplitude with respect to tokamak operation. Furthermore, the MCTB test implies an additional over-compression of conductors located in the straight leg of the TF coil in equatorial plane. The effect of this “cold-test cycling” will be discussed in terms of mechanical behavior, fracture of strands and tentative Tcs degradation estimation.
- 12 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Upgrade of CICC Mechanical Model and Case Study of ITER TF Conductor in Cold Test Conditions
This paper proposes to use an upgraded version of the Multifil simulation tool to model an ITER TF-like conductor in two cases: In tokamak and in cold test conditions. After briefly introducing the Multifil code, the paper will report the latest upgrades in terms of thermal equilibrium as well as simultaneous Lorentz and coil operational loads. We will present a new post-processing of the fractured filamentary area, which relies on a memory of the fracture map along all the loading steps. Then, considering ITER is currently building a magnet coil test bench (MCTB) with the capability to cold test some of the TF coils at nominal current (68 kA) in a standalone situation, we will discuss how mechanical modelling of the TF conductor is relevant for assessing the impact of the test sequence on the Nb3Sn conductor degradation. We will present a new loading sequence, representative of the test facility conditions, with a different Lorentz force direction and amplitude with respect to tokamak operation. Furthermore, the MCTB test implies an additional over-compression of conductors located in the straight leg of the TF coil in equatorial plane. The effect of this “cold-test cycling” will be discussed in terms of mechanical behavior, fracture of strands and tentative Tcs degradation estimation.
- 30 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-6
Thermohydraulical Analysis and Fast Assessment of Operating Windows for JT-60SA TFC Commissioning
JT-60SA Toroidal Field Coils (TFC) comprise each a Winding Pack (WP), with 6 Cable-In-Conduit Conductor (CICC) lengths wound in 6 double-pancakes operating at 25.7 kA nominal current and 4.7 K temperature as well as stainless steel casing cooled by forced flow channels. Second phase of Integrated Commissioning (IC) have been performed during 2023 with current discharge and induced AC losses in the CICC and eddy currents in the structures. A Fast Assessment of Operating Window (FAOW) model was developed for this purpose and permits to assess heat loads inputs, the heat transfer from casing to WP with inertia effect and time delay, and the cooling capacities (through heat exchanger). This FAOW model is coupled to Superconductors Thermohydraulical and Resistive Electrical Analytical Model (STREAM) and permits to evaluate helium pressure and temperature increase in cooling loop. The IC 18 kA current discharge measurements are compared to calculated results thus validating models and analyses. Predictive calculated results for other current discharge values (15, 18, 20, 23.7 and 25.7 kA) are presented and discussed with the maximal helium pressure limits, and safety aspects (induced relief valves opening or not). These analyses of current values operating windows have been confirmed by further plasma operation at 23.7 kA. Even if the limits of the model are discussed, the main interest consists of rapid execution time duration (only few minutes) compared to numerical codes (several hours). This work and fast analysis tool and model (FAOW-STREAM) can be also useful for further performances analyses in view to recommend their use in similar ITER or EU-DEMO magnets, with possibility of real-time feed-forward calculations/control.
- 30 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-6
Thermohydraulical Analysis and Fast Assessment of Operating Windows for JT-60SA TFC Commissioning
JT-60SA Toroidal Field Coils (TFC) comprise each a Winding Pack (WP), with 6 Cable-In-Conduit Conductor (CICC) lengths wound in 6 double-pancakes operating at 25.7 kA nominal current and 4.7 K temperature as well as stainless steel casing cooled by forced flow channels. Second phase of Integrated Commissioning (IC) have been performed during 2023 with current discharge and induced AC losses in the CICC and eddy currents in the structures. A Fast Assessment of Operating Window (FAOW) model was developed for this purpose and permits to assess heat loads inputs, the heat transfer from casing to WP with inertia effect and time delay, and the cooling capacities (through heat exchanger). This FAOW model is coupled to Superconductors Thermohydraulical and Resistive Electrical Analytical Model (STREAM) and permits to evaluate helium pressure and temperature increase in cooling loop. The IC 18 kA current discharge measurements are compared to calculated results thus validating models and analyses. Predictive calculated results for other current discharge values (15, 18, 20, 23.7 and 25.7 kA) are presented and discussed with the maximal helium pressure limits, and safety aspects (induced relief valves opening or not). These analyses of current values operating windows have been confirmed by further plasma operation at 23.7 kA. Even if the limits of the model are discussed, the main interest consists of rapid execution time duration (only few minutes) compared to numerical codes (several hours). This work and fast analysis tool and model (FAOW-STREAM) can be also useful for further performances analyses in view to recommend their use in similar ITER or EU-DEMO magnets, with possibility of real-time feed-forward calculations/control.