Saeed Arazm
Research Subjects
Research Interests
Saeed Arazm has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Kamal Al-Haddad
Department of Ecole de Technologie Superieure, University of Quebec, Montreal, QC, Canada
3 shared publications - Fadia Sebaaly
Saint joseph university-ESIB, Lebanon
1 shared publication - Hadi Youssef Kanaan
Saint-Joseph University of Beirut
1 shared publication - Rawad Zgheib
Institut de Recherche dHydro-Qubec (IREQ), Varennes, QC, Canada
1 shared publication - Sandy Atanalian
École de Technologie Supérieure, ÉTS, Montreal, Canada
1 shared publication
Latest Publications
- 17 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Three-Phase ZPUC-MMC Grid Connected Converter
Modular Multilevel Converter (MMC) is a promising topology that gained lot of interest in medium-voltage grid-connected applications due to its modularity, scalability, and adaptability. Although increasing the number of submodules per arm leads to a higher number of voltage levels and better waveforms quality, the size and then the cost of the converter remains a challenge. Therefore, a trade-off between topology complexity and power quality exists. This paper proposes an MMC based on Z Packed U-Cell converter as Submodule (ZPUC-SM) to generate a higher number of voltage levels with reduced number of SMs. When compared to HB-MMC, this topology features reduced components count for generating the same voltage levels. Thus, the candidate topology is considered to be a promising solution for medium-voltage applications connecting the utility. This paper details the design, modeling and control of ZPUC-MMC operating as a three-phase grid-connected converter. The controller task is to regulate output current to fulfill grid connectivity requirements. A Phase shifted-PWM with an integrated voltage balancing algorithm takes in action of controlling the three-capacitors voltages of each arm. Thus, no additional voltage controllers are required. The performance of the proposed converter along with its control system are validated with MATLAB/SIMULINK, and the simulation results validate the robustness and effectiveness of the proposed control during both steady-state and dynamic operations.
- 17 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Three-Phase ZPUC-MMC Grid Connected Converter
Modular Multilevel Converter (MMC) is a promising topology that gained lot of interest in medium-voltage grid-connected applications due to its modularity, scalability, and adaptability. Although increasing the number of submodules per arm leads to a higher number of voltage levels and better waveforms quality, the size and then the cost of the converter remains a challenge. Therefore, a trade-off between topology complexity and power quality exists. This paper proposes an MMC based on Z Packed U-Cell converter as Submodule (ZPUC-SM) to generate a higher number of voltage levels with reduced number of SMs. When compared to HB-MMC, this topology features reduced components count for generating the same voltage levels. Thus, the candidate topology is considered to be a promising solution for medium-voltage applications connecting the utility. This paper details the design, modeling and control of ZPUC-MMC operating as a three-phase grid-connected converter. The controller task is to regulate output current to fulfill grid connectivity requirements. A Phase shifted-PWM with an integrated voltage balancing algorithm takes in action of controlling the three-capacitors voltages of each arm. Thus, no additional voltage controllers are required. The performance of the proposed converter along with its control system are validated with MATLAB/SIMULINK, and the simulation results validate the robustness and effectiveness of the proposed control during both steady-state and dynamic operations.
- Open Access
- 1 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 3, 1-13
A Novel Single DC Source Three-Phase Wye Packed U-Cell (Y-PUC) Converter
A new configuration of three-phase Wye Packed U-cells (Y-PUC) with a single DC source is proposed in this paper. In fact, this configuration represents a single DC source modular three-phase PUC converter. The DC source on PUC topology is replaced by a flying capacitor to obtain a suitable submodule. Moreover, the modularity of the Y-PUC configuration makes it an appropriate alternative for MMC applications. Furthermore, the proposed structure is an advantageous configuration for high voltage applications such as high voltage direct current (HVDC) transmission lines with the capability of DC fault handling. All PUC topologies such as PUC5, PUC7, PUC9, PUC15 can be replaced in the modules of this proposed single-phase and three-phase configuration to multiply the load voltage levels for improving the output waveform. Active voltage balancing technique through carrier-based modulation is applied. System modeling and operating sequences are developed. Simulation and experimental results are presented and discussed to validate the performance of the proposed structure.
- 1 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 3, 1-13
Open AccessA Novel Single DC Source Three-Phase Wye Packed U-Cell (Y-PUC) Converter
A new configuration of three-phase Wye Packed U-cells (Y-PUC) with a single DC source is proposed in this paper. In fact, this configuration represents a single DC source modular three-phase PUC converter. The DC source on PUC topology is replaced by a flying capacitor to obtain a suitable submodule. Moreover, the modularity of the Y-PUC configuration makes it an appropriate alternative for MMC applications. Furthermore, the proposed structure is an advantageous configuration for high voltage applications such as high voltage direct current (HVDC) transmission lines with the capability of DC fault handling. All PUC topologies such as PUC5, PUC7, PUC9, PUC15 can be replaced in the modules of this proposed single-phase and three-phase configuration to multiply the load voltage levels for improving the output waveform. Active voltage balancing technique through carrier-based modulation is applied. System modeling and operating sequences are developed. Simulation and experimental results are presented and discussed to validate the performance of the proposed structure.
- Open Access
- 29 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 1, 97-113
ZPUC: A New Configuration of Single DC Source for Modular Multilevel Converter Applications
Z packed U-cell (ZPUC) converter topology is presented in this paper as a new type of multilevel converter topology that can be operated in a single-phase as well as in three-phase configurations while using a single DC source. Since each U-cell includes two switches and one capacitor, in this topology, three U-cells are needed to generate 5 or 7 voltage levels. Moreover, the configuration proposed for the ZPUC is more appropriate for high-power application modular multilevel converters (MMCs) to increase the voltage levels compared to other topologies. Accurate voltage balancing on small-sized auxiliary capacitors is due to an integrated modulation strategy without using additional controllers; additionally, the reduction of total harmonic distortion (THD) in AC currents for higher voltage levels is an advantage of this configuration. A full topology sequence of operation and performance analysis of ZPUC based on the 5-L inverter is investigated in Matlab-Simulink and experimentally validated on a 3 kVA prototype. The obtained results illustrate the good dynamic performance of the proposed topology and the implemented integrated switching pattern voltage balancing.
- 29 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 1, 97-113
Open AccessZPUC: A New Configuration of Single DC Source for Modular Multilevel Converter Applications
Z packed U-cell (ZPUC) converter topology is presented in this paper as a new type of multilevel converter topology that can be operated in a single-phase as well as in three-phase configurations while using a single DC source. Since each U-cell includes two switches and one capacitor, in this topology, three U-cells are needed to generate 5 or 7 voltage levels. Moreover, the configuration proposed for the ZPUC is more appropriate for high-power application modular multilevel converters (MMCs) to increase the voltage levels compared to other topologies. Accurate voltage balancing on small-sized auxiliary capacitors is due to an integrated modulation strategy without using additional controllers; additionally, the reduction of total harmonic distortion (THD) in AC currents for higher voltage levels is an advantage of this configuration. A full topology sequence of operation and performance analysis of ZPUC based on the 5-L inverter is investigated in Matlab-Simulink and experimentally validated on a 3 kVA prototype. The obtained results illustrate the good dynamic performance of the proposed topology and the implemented integrated switching pattern voltage balancing.